Panasonic Cf 18ddazxmm Owners Manual

							11
Getting Started
Using the Tether
The tether can be attached to the bottom right or bottom left corner of the display.  It prevents
the pen (included) from falling accidentally.
Attaching the Tether
1
23
4
Tether
CAUTION
When closing the display, be careful not to catch the tether between the display and
main part of the computer. (See the figure below.) 
						

							12
Getting Started
1
First-time Operation
Read the steps below to help you learn what parts are included, and to gain an understanding of
some basic computer-related operations.
1Confirm the inclusion of all parts.
Make sure the parts shown in the figure have been supplied.  If any of these items are
missing or are not working properly, contact Panasonic Technical Support.
3Insert the battery pack.
Unlock the cover by sliding the latch to the right.1
CAUTION
Do not touch the terminals on the battery pack and the computer.  The
battery pack may no longer function properly if the contacts are dirty or
damaged.  Also, the computer may not operate properly.
Be sure to insert the battery pack as illustrated.
2Slide the latch down, and then without releasing it, open the cover as illustrated.
3Slide the battery pack inward until it is firmly in place.
2Read the LIMITED USE LICENSE AGREEMENT. ( page 36)
Be sure to read the LIMITED USE LICENSE AGREEMENT before breaking the
seal on the computer’s packaging.
Model No : CF-AA1623A
AC adaptor .......... 1
Model No :CF-VZSU30
AC Cord ............... 1Battery Pack ........ 1
Modem Telephone
Cable ...................... 1
Operating Instructions
(This book).................... 1
Windows
® Book.... 1
Product Recovery
CD-ROM ................ 4
(  “Digitizer”)
Soft Cloth ............... 1
Confirm that the latch lock is correctly in place. If you carry your computer
without the latch lock in place, the battery pack may fall out.
Before using the battery pack, carefully read “Precautions (Battery Pack)”
(
 page 7).
CAUTION
4Close the cover until it clicks into place.
Latch
Cover
2
3
4
Pen .......................... 1
Tether ...................... 1Shoulder Strap........ 1
( page 9) ( page 11)
5Lock the cover by sliding the latch to the left.
5 
						

							13
Getting Started5Open the display.
1Pull up on the latch A and release the latch B.
2Lift open the display.
Slide the power switch and hold it for approximately one second until the power indi-
cator turns on before releasing it.
CAUTION
Connect your computer to a power outlet.
CAUTION
Be sure the AC adaptor is connected until completing the first-time use operation.
When using the computer for the first time, do not connect any peripheral de-
vice except the battery pack and AC adaptor to the computer.
Handling the AC adaptor
Do not twist or pull the AC power cord forcefully.  Doing so may damage the
connections.
Use only the specified AC adaptor with your computer.  Using an AC adaptor
other than the one supplied might damage the battery and/or the computer.
When the DC plug is not connected to the computer, disconnect the AC cord
from your AC wall outlet.
Problems such as sudden voltage drops may arise during periods of thunder
and lightning.  Since this could adversely affect your computer, an uninterruptible
power source (UPS) is highly recommended unless the battery pack is installed.
4
6
Turn your computer on.
Latch A
Do not slide the power switch and hold it for more than four seconds; this will
cause the power to be turned off forcibly.
Do not slide the power switch repeatedly.
Once the computer is powered off, you must wait at least ten seconds before
powering it on again.
Setup Windows.
Moving the cursor () or clicking buttons can be performed with the touch pad (
page 20). Latch B
2
1
Power Switch 
Power Indicator 
DC-IN Jack
DC IN 16 V
1At [Welcome to the Windows XP Setup Wizard], select [Next].
2After reading the agreement, select [I accept this agreement] or [I don’t accept this
agreement], then select [Next].
NOTE
 If [I don’t accept this agreement] is selected, the Windows setup will be aborted.
Do not press any keys or touch the touch pad until [Windows XP Professional
Setup] is displayed.
The digitizer function will not operate during Windows setup. Use the touch
pad or the keyboard to perform the following procedure.
CAUTION
3Select settings for your region, then select [Next].
4Enter your name and organization and then select [Next].
7 
						

							14
Getting Started
First-time Operation
1Select [start] - [Control Panel] - [User Accounts] - [Create a new account].
2Enter a name for the new account, then select [Next].
3Select [Computer administrator], then select [Create Account].
4
Select the new account you have created and select [Create a password].
Follow the instructions on the screen to create a password.
5Select [start] - [Turn Off Computer] - [Restart] to restart the computer.
CAUTION
Remember this password!  If the password is forgotten, Windows cannot be oper-
ated. 
 You can create a password reset disk beforehand ( page 16).
5Enter your computer name and administrator password and then select [Next].
CAUTION
Remember this password!  If the password is forgotten, Windows cannot be
operated.
6Enter the correct date, time and time zone, then select [Next].
The computer will restart.
NOTE
It will take some time before the computer restarts and the screen of step
 7  is displayed.  Wait, and do not press any keys, or touch the touch pad, etc.
7Enter your administrator password and select .
8At [Welcome to Tablet Computing], you can learn the basic operations for
Microsoft® Windows®  XP Tablet PC Edition.
If the cursor can not be pointed correctly with the pen, perform [Calibration] in
[start] - [Control Panel] - [Printers and Other Hardware] - [Tablet and Pen Set-
tings].  When you perform the calibration, hold the pen at the same angle as you
would when actually using it.
Perform the calibration separately for [Landscape] and [Portrait].
8Create a new account.
When creating a new user account:
 If you make mail settings, create password reset disks (
 page 16), or conduct
other related operations before creating the user account, you will be unable to use
any previous mail history or settings.
 When you create the first new account, you can only select [Computer administra-
tor].
Once a “Computer Administrator” account has been created, you can create addi-
tional limited user accounts.
Note also that only the added user account will be displayed in the Welcome screen.
The account for the administrator created during Windows setup will not be dis-
played.
If the characters or icons on the screen are too small and difficult to see, after complet-
ing step 
8, select [start] - [All Programs] - [Panasonic], and select [Icon Enlarger].  This
will allow you to magnify the display of characters and icons on the screen.
The [Icon Enlarger] can be set separately for each account.
NOTE   
						

							15
Getting Started
This concludes the first-time use operation guidelines.
9Start up Windows Media Player.
Log on with the administrator authority, and select  on the screen.
After this, start up the application following the instructions on the screen.
During this process, you will be required to agree to the license agreement.  For Win-
dows Media Player, it is necessary to agree to the license agreement for each account
created.
If [I Decline] is selected or a window is closed without any decision being made in the
license agreement, no icons on the desktop may be selected. In this case, restart the
computer.
After completing the settings, select  on the screen, and close the Windows Media
Player.
If you use the wireless LAN, be sure to refer to the Reference Manual’s “Wireless LAN”.
NOTE     
						

							16
Getting Started
Depending on the Windows settings, installed applications, and drivers, menus and
other displays may differ, or some functions (such as use of the password reset disk)
may be inoperable.  Check with your system administrator for details.
You can select Classic view for the Control Panel or select the Classic Start menu.
You can also change the way a user logs on or off.
The procedure in this manual uses the method or view of the Windows XP default
setting (not Classic view or Classic Start menu etc.).
Resetting the password
Windows XP has a function to reset a forgotten password.
To use this function, you need to create a password reset disk beforehand following
the steps below.
1Connect the USB floppy disk drive (optional: CF-VFDU03) to your computer.
2Select [start] - [Control Panel] - [User Accounts] and select the account you used
to logon.
3Select [Prevent a forgotten password] from the [Related Tasks] menu of the ac-
count you have logged on to, and create a password reset disk following the on-
screen instructions.
Store the password reset disk in a safe place.
·Only the logon password for each account can be reset.
The password set in the Setup Utility cannot be reset.  (
  “Setup Utility”)
Information for Windows XP
First-time Operation 
						

							17
Operation
1Open the display.
Starting Up/Shutting Down
Starting Up
2Turn your computer on.
Slide the power switch and hold it for approximately one second until the power
indicator turns on before releasing it.
2
CAUTION
While booting, avoid the following until the hard disk drive indicator ()
has turned off.
 Connecting or disconnecting the AC adaptor.
 Touching the power switch or the tablet buttons.
 Performing any keyboard, touch pad, digitizer (or external mouse) opera-
tions.
 Closing the display.
Once the computer is powered off, you must wait at least ten seconds before
powering it on again.
When using this computer with the battery pack only, it may take some time
for the power to turn on after sliding the power switch.  In this case, slide the
power switch and hold it for more than one second.  This phenomenon oc-
curs because the standby power is minimized while the power is turned off; it
is not a malfunction.
When the CPU temperature rises, the computer may not power on to prevent
the CPU from overheating.  Should this happen, allow the computer to cool
down then switch the power on again.
If the computer still does not power on, contact Panasonic Technical Support. Pull up on the latch A and release the latch B.
1
1
Lift open the display.2
Latch B
Power Switch 
Power Indicator 
Latch A
When the power is turned on, sometimes the message “Warming up the sys-
tem. Please wait...” (up to 25 minutes) is displayed or the battery indicator
alternately blinks green and orange.  This function is designed to prevent hard
disk drive malfunctions that may occur at low temperatures.  Wait for the com-
puter to start up.
NOTE
 Enter your password*1 and press   Enter   .(  “Security Measures”)
Will Start
 Will Not Start
(Power off)
If [Enter Password] is displayed,
*1Supervisor Password or User Password set in the Setup Utility
(not the Windows password).
Three incorrect attempts
or
No password for about a minute The correct password
Enter Password  [          ] 
						

							18
Operation
Starting Up/Shutting Down
The power saving function is factory set, so if there is no input from a key, the touch
pad, the tablet button, the digitizer or an external mouse (when one is connected) for
a certain interval of time, the power to the LCD and hard disk may be turned off.
The LCD will resume operation when the touch pad, the digitizer or an external
mouse (when one is connected) is used or a key or the tablet button is pressed.
The power to the LCD may be turned off even when an application software is
being installed.  In this case, because it is conceivable that a selection dialog box
will be shown, do not press   Space    or    Enter    to attempt to resume from this
condition as doing so may trigger a selection, but instead, press a key unrelated to
the direct triggering of a selection, like    Ctrl   .
In addition, when the computer is left alone, it automatically enters the standby or
hibernation mode.  The computer will resume by sliding the power switch.  (
  “Standby/Hibernation Functions”)
NOTE
3Log on to Windows.
After confirming that the hard disk drive indicator () has turned off, select the user
and input the password, then select 
.  Until the correct password entered, the com-
puter will not operate.
4Select your application.
You are able to start working on your computer.   
						

							19
Operation
Shutting Down (power off your computer)
To quickly resume computer operation after shutting down,
The standby or hibernation function is available (
  “Standby/Hibernation
Functions”).
When you leave the computer or interrupt your work...
If you use the “Standby” or “Hibernation” function, then when you turn on the
power next time, the application software and files you were using before will be
displayed, and you can restart the same operations immediately (
 
“Standby/Hibernation Functions”).
NOTE
1Save important data and close each application.
2Select [start] - [Turn Off Computer].
3Select [Turn Off].
Your computer will power off automatically.
Restarting your computer (without shutting down)
Select [Restart].
To shut down using the keyboard;
Press       ,    U   , and select [Turn Off] with    U   .
CAUTION
Do not do the following during the shutdown/restart procedure.
 Connecting or disconnecting the AC adaptor.
 Touching the power switch.
 Performing any keyboard, touch pad, digitizer, tablet buttons, or external mouse
operations.
 Closing the display.
4Close the display.
1Close the display.
2Pull up on the latch A.
3Position the latch B on the display side, then bring the latch A down to fix the
display in place.
Latch A
2
1
3
Latch A Latch B 
						

							20
Operation
Touch Pad (Basic Operation)
Use the touch pad to move the cursor on the display and perform normal computer operations.
For instructions on how to operate, refer to 
 “Touch Pad”.
Handling the Touch Pad
By design the touch pad is to be used with a finger tip only.  Do not place any object on the
work surface or press down forcefully with sharp-pointed objects (e.g., nails) or hard ob-
jects that can leave marks (e.g., pencils and ball point pen).
Try to avoid having any harmful substances such as oil, come in contact with the touch pad.
The cursor may not work properly in such cases.
When the touch pad becomes dirty:
Wipe to remove dirt by using a dry soft cloth such as gauze or a soft cloth first applied with
detergent diluted with water and then thoroughly wrung.
Do not use benzene, thinner, or rubbing alcohol.  Doing so may adversely affect the surface,
e.g., discoloration. In addition, do not use commercially-available household cleaners and
cosmetics, as they may contain components harmful to the surface.or
Two quick taps, but on
the second tap leaving
your finger down (apply-
ing pressure) and moving
it on the work surface.While holding down the
button, moving your fin-
ger on the work surface.
or Function
Touch Pad Operation
Moving the Cursor
Tapping/Clicking
Double-Tapping/
Double-Clicking
Dragging
or Move the tip of your finger lightly
over the surface.
tappingclicking
double-tapping
Left ButtonRight Button Work Surface
double-clicking