Panasonic Cf 07 Mk1 Winxp V02 28 2005 Owners Manual

21
Operation
Starting Up/Shutting Down
1Turn your computer on
Press the power switch and hold it for approximately
one second until the power indicator turns on before
releasing it.
Starting Up
2After confirming the display status in-
dicator lit, turn on the wireless
display
(Operating Instructions of the wireless
display)
After confirming that the power indicator has turned on, avoid the following
until Windows has completed loading.
• Connecting or disconnecting the AC adaptor.
• Touching the power...

22
Operation
Starting Up/Shutting Down

If [Enter Password] is displayed
3Log on to W indows
After confirming that the hard disk drive indicator () has turned off, select the
user and input the password, then select 
. Until the correct password is entered,
the computer will not operate.
When an application or file that was previously displayed
appears on your screen
The standby or hibernation mode (  “Standby/Hibernation Functions”)
has been set.
Three incorrect attempts
or
No password for about a...

23
Operation
4Select your application
You are able to start working on your computer.
The power to the wireless display may be turned off while Windows is set-
ting up or even when an application software is being installed.

• If the power indicator lights, the wireless display will resume operation
when the touchscreen is used.
• If the power indicator does not light, the wireless display will resume op-
eration when the power switch is pressed.

The external display will resume operation when the...

24
Operation
Shutting Down (power off your computer)
Restarting your computer (without shutting down)
Select [Restart].
To shut down using the keyboard,
You may select to press    Ctrl    +   Esc   ,        or        then select the menu
with                     .
To quickly resume computer operation after shutting down,
The standby or hibernation function is available (
  “Standby/Hi-
bernation Functions”). This procedure is for shutting down the computer without using the standby or hiberna-
tion...

25
Operation
Reference Manual
The Reference Manual and the Important Tips can be accessed on your computer. When a
printer is connected, these manuals can also be printed.
The Reference Manual explains functions for you to make greater use of the computer,
such as how to add peripheral devices, how the Setup Utility works, and other useful
information. (Refer to the cover of this manual for a list of the main contents included.)
Important Tips provides information on how to maximize use of the battery...

26
Troubleshooting
List of Error Codes 
The following is a list of the messages that BIOS can display. Most of them occur during
POST.  Some of them display information about a hardware device, e.g., the amount of memory
installed.  Others may indicate a problem with a device, such as the way it has been configured.
Following the list are explanations of the messages and remedies for reported problems.
If your system displays any of the below error messages other that the ones marked with an
asterisk...

27
Troubleshooting
*0280  Previous boot incomplete - Default configuration used
Previous POST did not complete successfully.  POST loads default values and offers to run
Setup.  If the failure was caused by incorrect values and they are not corrected, the next boot
will likely fail.  On systems with control of wait states, improper Setup settings can also termi-
nate POST and cause this error on the next boot.  Run Setup and verify that the wait-state
configuration is correct.  This error is cleared the...

28
Troubleshooting
Parity Check 2 nnnn
Parity error found in the I/O bus.  BIOS attempts to locate the address and display it on the
screen.  If it cannot locate the address, it displays ????.
Press  to resume,  to Setup
Displayed after any recoverable error message.  Press  to start the boot process or  to
enter a Setup and change the settings. Write down and follow the information shown on the
screen.
List of Error Codes  

29
Troubleshooting
Dealing with Problems (Summary)
When a problem occurs, power off the wireless display, then connect the optional port
replicator (CF-VEB071), external keyboard and external display and refer to this page.  The
“Reference Manual” also contains detailed information.  If a problem appears to be related
to a software application, read the software related manual.  If you still cannot troubleshoot
the problem, contact Panasonic Technical Support.
 Starting Up
The power indicator
or battery...

30
Troubleshooting
Dealing with Problems (Summary)
When resuming
from the standby or
hibernation  mode,
[Enter Password]
does not appear even
if a password has
been set in the Setup
Utility
The DISPLAY
READY indicator
does not go on even
when the HDD indi-
cator goes off
When the adminis-
trator password is
forgotten
When the previous
item is not the cause
Even when a password has been set in the Setup Utility,
[Enter Password] does not appear when the computer re-
sumes from the standby or hibernation...