Panasonic Cf 07 Mk1 Winxp Reference Owners Manual

21
A port replicator is available as an option (CF-VEB071).  This device allows a
variety of peripherals to be connected including a headphone or microphone,
etc.
The port replicator connects to the expansion bus connector on the bottom
of your computer.
For more detailed information, refer to the operation manual of the port
replicator.
Port Replicator
When connecting the external display to the display port on the port
replicator, the characters on the external display may be blurred if 1280 x
1024 (or...

22
Parallel Port
Printer 
You may need to install a driver for your printer.  Follow the on-
screen instructions and refer to the operation manual of the printer
on how to install the driver.
Confirm whether or not the setting for the [Parallel Port] in the
Setup Utility is optimal(
 page 30)
NOTE
4Turn on the printer, then turn on your computer
5Setting your printer
Select [Start] - [Printers and Faxes].
Find your printer’s icon, double-click on it, then select [Printer] - [Set as
Default Printer].  If...

23
2Connect your computer to the optional port replicator
( Operating Instructions of the port replicator,  page 21)
3Connect the external display to the port replicator
4Turn on the external display, then turn on your computer
1Power off your computer (  "Starting Up/Shutting Down")
Do not shut down using the standby or hibernation mode.
External Display Port
External Display 
NOTE
Port Replicator
For more detailed information, refer to the operation manual of the
external display.
The external...

24
Installing a USB device
USB Devices
USB devices may be connected or removed without turning off the
computer's power.
For more detailed information, refer to the operation manual of the USB
device.
You may need to install drivers compatible with the OS you are using
for your USB devices. Follow the on-screen instructions and refer to
the operation manual for USB devices on how to install the driver.
When a USB device is connected, there are cases the standby or hiberna-
tion function will not...

25
Removing a USB device
Save important data and close each application.
Do not remove a USB device while your computer is in the standby or
hibernation mode.
1Select   on the taskbar and select the USB device,
then select [Stop]
Follow the on-screen instructions.
(When 
 is not displayed or when the USB device has been removed
after the computer is turned off, this step is not necessary.)
CAUTION
After selecting , do not press [Stop] for [PRISM2 IEEE 802.11 PC
CARD Adaptor].
CAUTION
2Remove the USB...

26
LAN 
LAN portWhen using the computer as a network computer, some additional settings may
have to be made depending on the usage conditions. We recommend asking your
system administrator or the person in charge of the network.
If you are unable to connect to the network (when the indicator of your\
 HUB unit
does not light): 1 Select [Device Manager] in [Start] - [Control Panel] - [Performance and \
Main-
tenance] - [System] - [Hardware].
2 Select the network adaptor name you are using from [Network...

27
LAN 
Wake up from LAN
Be sure to connect the AC adaptor, and enable the supply of power.
Make settings to allow the use of a Local Area Network.
The computer will not “wake up” if the LAN cable is disconnected and recon-
nected.
The Wake up from LAN function will not operate under the following conditions:
When the computer has been shut down
When the power switch is pressed over for four seconds or longer to turn off
the power (e.g., when the computer hangs)
When the AC adaptor and battery pack are...

28
Setup Utility 
Running the Setup Utility
Setup Utility can be run only when the port replicator, external display and external
keyboard are connected.
NOTE
1Power off your computer (  "Starting Up/Shutting Down")
Do not shut down using the standby or hibernation mode.
2Connect your computer to the port replicator, external display,
external keyboard and external mouse
 
( Operating Instructions of the port replicator,  page 21)
3Turn on the computer
4Press   F2   while [Panasonic] boot screen...

29
Normal Temperature
High Temperature
Refreshing the Battery  ( page 15)
Setup Utility 
Environment
Refresh Battery
Main Menu
Model No: xxxxxxxxxxxx
Serial No: xxxxxxxxxx
BIOS Version: Vx.xxLxx
System Time: [xx:xx:xx]*
1
System Date: [xx/xx/xxxx]*2
System Memory: xxx MB
Primary Master: xx GB
Secondary Master: CD Drive
Environment: [Normal Temperature]
Refresh Battery
(     :  Default)Parameters
*1Time is shown in 24-hr. style.
*2Date is shown in order of Month/Day/Year. 

30
Device Configuration
Serial Port A*1
I/O IRQ*2
Serial Port B*3
I/O IRQ*2
Wireless Modem*4
I/O IRQ
Resume on W ireless Modem
GPS*5
I/O IRQ
Parallel Port
Mode*6
I/O IRQ*2
LAN
Wake up from LAN*7
VDW07 Controller
Legacy USB Support
Device Configuration : [BIOS]
Serial Port A: [Auto]
Serial Port B: [Auto]
Wireless Modem: [Auto]
GPS: [Auto]
Parallel Port: [Auto]
Mode: [ECP]
LAN: [Enable]
Wake up from LAN: [Disable]
VDW07 Controller: [Enable]
Legacy USB Support: [Enable]
BIOS OS
Disable Enable Auto
3F8/IRQ4...