Panasonic Cf 07 Mk1 Winxp Owners Manual

							41
Dealing with Problems (Advanced)
The cursor does not move
from mouse operations
The device connected to
the serial port does not
work
External mouse or
trackball connected to the
external keyboard/mouse
port does not work
A PC Card does not work
The address map for IRQ,
I/O port address, etc. is
unclear
A USB device does not
work
It is not easy to hear of
the microphone sound.Check your mouse connection, then reboot the com puter from the keyboard.
From the keyboard, you may select to press   Ctrl   +   Esc   ,      or      then select
[Shut Down].
Check the connection.
Confirm that the device driver for the serial port works. Refer to the reference
manual of the device.
Confirm that two mouse devices are not connected, one through the external key-
board/mouse port and the other through the serial port.
Confirm that [Serial Port A] or [Serial Port B] has not been set to [Disable].
Depending on the device, the operable I/O and IRQ may be limited. Try different
I/O and IRQ settings in the Setup Utility.
Some devices may not work since the serial port of the port replicator allows the
selection of only [3E8/IRQ5] or [2E8/IRQ10]. In such cases, we recommend using
the serial port of the computer.
A mouse connected to the serial port will not work.
In some circumstances, if a PS/2 external mouse with a serial interface conversion
function is connected to the port, it may not operate normally.  Try connecting it to the
serial port.
Make sure the card is properly inserted.
Confirm that the card conforms to the PC Card Standard.
Note that after a driver (PC card driver or other) is installed, the computer must be
restarted.
Check that the proper port settings have been made.
Read the PC Card’s manual. Or, you may need to call the manufacturer of the PC Card.
Try removing / reinserting the PC Card by following the proper procedure. (
page 19)
Confirm that a driver for your operating system has been installed.
Check the address map by going to [View] - [Resources by type] in [Control Panel] -
[Performance and Maintenance] - [System] - [Hardware] - [Device Manager].
Make sure a driver is installed.
Contact the manufacturer of the product.
1Double click  on the taskbar.
2Select [Options] - [Properties].
3Check [Playback], add the check mark for [Microphone], then select [OK].
4Select [Options] - [Advanced Controls].
5Select [Advanced] in [Microphone].
6Add the check mark for [2. Microphone Boost] and select [Close].
7Click 
  in the top of right corner of the window.
 Connecting Peripherals   
						

							42
Has the floppy disk been correctly inserted?
Has the floppy disk been correctly formatted?
Your floppy disk content may be corrupted.
Is the disk write-protected?
Select [Format] in [Start] - [My Computer] - [3 1/2 Floppy (A:)] - [File].  After confirming
the disk volume and format type, start formatting.
Your drive or file may not have been properly set.
Check to see if the hard disk is full.  If it is full, delete unnecessary files.
Your hard disk content may be corrupted.  Contact Panasonic Technical Support.
Try testing another drive or media.
You may need to clean the lens or disc.
Is the disc loaded on the tray correctly?
Is the disc bent, scratched, or dirty?
Is the computer powered on?
To remove a disc when the computer is powered off, insert a sharp object such as the
bent-out tip of a paper clip into the emergency hole.  Pushing it completely to the end
will free the tray so that it can be pulled out.
Did you open the CD-ROM drive or remove the MPEG disc while it was operating?
Re-insert the MPEG disc and close the CD-ROM drive.  Press   Enter   .
Is the disc bent labeled?
Check to see if the disc is inserted correctly, and check that the disc is in good
condition. If the disc is good and inserted correctly, set the [CD Drive Speed] to
[Low] in the Setup Utility. (
 page 32)
Dealing with Problems (Advanced)
Cannot read/write to a
floppy disk
Unable to write to a
floppy disk
How to format a floppy
disk is unclear
Unable to read/write to
the hard disk
When the previous item
is not the cause
Trouble has occurred
with the disc
The access lamp does
not light
Cannot play disc or read
data from it
Cannot eject disc
A blue background ap-
pears on the screen with
the MPEG image
The CD-ROM drive vi-
brates excessively
 Disk Operations
Emergency Hole
Press  Ctrl   +   Shift   +   Esc   to open Task Manager and close the software
application which is not responding.
After shutting down by pressing the power switch for more than four seconds,
press the power switch to power on and open the application again.
If the program no longer works normally, select [Start] - [Control Panel] - [Add or
Remove Programs] to delete the program using the following procedure. Then
reinstall the program.
Install the software after powering off the computer and the wireless display and then
connecting the port replicator, optional USB floppy disk drive, external keyboard and
external display. No responseUnable to install
 Others 
						

							43
Copyright
This manual is copyrighted by Matsushita Electric Industrial Co., Ltd. with all rights reserved.  No part of this manual may
be reproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd.
No patent liability is assumed with respect to the use of the information contained herein.
© 2003 Matsushita Electric Industrial Co., Ltd.  All Rights Reserved.
Disclaimer
Computer specifications and manuals are subject to change without notice.  Matsushita Electric Industrial Co., Ltd.
assumes no liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the
computer and the manuals.
Trademarks
PS/2™ is a trademark of International Business Machines Corporation.
Microsoft, W indows and the Windows logo are registered trademarks of Microsoft Corporation of the United States and/
or other countries.
Pentium is a registered trademark of Intel Corporation.
Adobe
® and Acrobat® are either registered trademarks or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd.
PCE0132A_XP