Panasonic Cd Stereo System Sc-akx18 Owners Manual

							11
RQT9899
Radio
Preparation
Press [RADIO/AUX] to select “FM”.
Manual tuning
1Press [PLAY MENU] to select “TUNE MODE”.
2Press [R, T ] to select “MANUAL” and then press 
[OK].
3Press [ 2/3 ] or [5 /6 ] to tune in to the 
station.
To tune automatically, press and hold the button until 
the frequency starts changing quickly.
“STEREO” is shown when a stereo broadcast is being 
received.
Using the main unit
1Press [TUNE MODE] to select “MANUAL”.
2Press [ 2/3 ] or [5 /6 ] to tune in to the 
station.
Memory presetting
You can preset up to 30 FM radio stations.
█Automatic presetting
1Press [PLAY MENU] to select “A.PRESET”.
2Press [ R, T ] to select “LOWEST” or “CURRENT” 
and then press [OK].
The tuner presets all the stations it can receive into 
the channels in ascending order.
To cancel, press [ 8].
█Manual presetting
1Press [PLAY MENU] to select “TUNE MODE”.
2Press [R, T ] to select “MANUAL” and then press 
[OK].
3Press [ 2/3 ] or [5 /6 ] to tune in to the 
station.
4Press [OK].
5Press [ R, T ] to select a preset number and then 
press [OK].
Re-do steps 3 through 5 to preset more stations.
The new station replaces any station that occupies 
the same preset number.
█Selecting a preset station
1Press [PLAY MENU] to select “TUNE MODE”.
2Press [ R, T ] to select “PRESET” and then press 
[OK].
3Press [ 2/3 ] or [5 /6 ] to select the preset 
station.
Using the main unit
1Press [TUNE MODE] to select “PRESET”.
2Press [ 2/3 ] or [5 /6 ] to select the preset 
station.
Improving the sound quality
1Press [PLAY MENU] to select “FM MODE”.
2Press [ R, T ] to select “MONO” and then press 
[OK].
To cancel, select “STEREO”.
“MONO” is also canceled when you change the 
frequency.
To memorize the setting
Continue with step four of “Manual presetting”.
Checking the signal status
Press [DISPLAY].
FM allocation setting
By main unit only
This system can also receive FM broadcasts allocated in 
0.1 MHz steps.
1Press [RADIO/AUX] to select “FM”.
2Press and hold [RADIO/AUX].
After a few seconds, the display panel shows the current 
minimum radio frequency. Release the button when the 
minimum frequency changes.
• To go back to the initial setting, re-do the above steps.
• Preset frequencies are erased after you change the  setting.
LOWEST Tuning begins from the lowest frequency.
CURRENT Tuning begins at the current frequency.
FM The FM signal is in monaural.
The system is not tune d in to a station.
FM ST The FM signal is in stereo.
FM MONO “MONO” is selected as the “FM MODE”.
ENGLISH
SC-AKX18 P RQT9899-P EN.fm  Page 11  Monday, April 14, 2014  10:41 AM  
						

							12
RQT9899
Clock and timers
Setting the clock
This is a 12-hour clock.
1Press [SETUP] to select “CLOCK”.
2Press [R, T ] to set the time and then press [OK].
To check the time
Press [SETUP] to select “CLOCK” and the press [OK].
In standby mode, press [DISPLAY].
Note:
Reset the clock regularly to maintain accuracy.
Sleep timer
The sleep timer turns off the  system after the set time.
1Press [SETUP] to select “SLEEP”.
2Press [R, T ] to select the setting (in minutes) and 
then press [OK].
To cancel, select “OFF”.
Note:
• The remaining time is always shown on the display. The  display changes temporarily when you perform other 
operations.
• The play and sleep timer can be used together.
• The sleep timer always comes first. Be sure not to set an  overlapping time.
Play timer(Except for Bluetooth® source )
You can set the timer to come on at a certain time to 
wake you up.
Preparation
Set the clock.
1Press [SETUP] to select “TIMER ADJ”.
2Press [ R, T ] to set the start time and then press 
[OK].
3Re-do step 2 to set the end time.
4Press [ R, T ] to select the source you want to play 
and then press [OK].
To start the timer
1Press [SETUP] to select “TIMER SET”.
2Press [ R, T ] to select “SET” and then press [OK].
“ # ” is shown.
To cancel, select “OFF”.
The system must be turned off for the timer to 
operate.
To check the setting
Press [SETUP] to select “TIMER ADJ” and then press 
[OK].
In standby mode, pres s [DISPLAY] two times.
Note:
• The timer starts at a low volume and increases gradually to 
the preset level.
• The timer comes on at the set time every day.
• If you turn off the system and then turn on again while the  timer is in operation, the timer will not stop at the end time.
SC-AKX18 P RQT9899-P EN.fm  Page 12  Monday, April 14, 2014  10:41 AM  
						

							13
RQT9899
External equipment
You can connect a VCR, DVD player etc., and listen to 
the audio through this system.
Preparation
• Disconnect the AC power supply cord.
• Turn off all equipment and read the appropriate operating instructions.
1Connect the external equipment.
2Press [RADIO/AUX] to select “AUX”.
3Play the external equipment.
To adjust the input level
1Press [SOUND] to select “INPUT LEVEL”.
2Press [ R, T ] to select “NORMAL” or “HIGH” and 
then press [OK].
Note:
• The default setting is “NORMAL”.
• Select “NORMAL” if the sound is distorted during “HIGH”  input level.
• Components and cables are sold separately.
• If you want to connect equipment other than those  mentioned, refer to the audio dealer.
• Sound distortion can occur when you use an adapter.
Others
Auto off
This system automatically turns off when you do not use 
it for approximately 20 minutes.
1Press [SETUP] to select “AUTO OFF”.
2Press [ R, T ] to select “ON” and then press [OK].
“A.OFF” is shown.
To cancel, select “OFF”.
Note:
This function does not work when you are in radio source or 
when a Bluetooth
® device is connected.
Bluetooth® standby
This function automatically  turns on the system when you 
establish a Bluetooth® connection from a paired device.
1Press [SETUP] to select “BLUETOOTH STANDBY”.
2Press [ R, T ] to select “ON” and then press [OK].
To cancel, select “OFF”.
Software version
You can check the software version of the system.
1Press [SETUP] to select “SW VER.” and then press 
[OK].
The software version is shown.
2Press [OK] again to exit.
Audio cable 
(not supplied)
Rear panel of 
this main unit
DVD player (not supplied)
ENGLISH
SC-AKX18 P RQT9899-P EN.fm  Page 13  Monday, April 14, 2014  10:41 AM  
						

							14
RQT9899
Tr o u b l e s h o o t i n g
Before requesting service, make the following checks. If 
you are in doubt about some of the check points, or if the 
solutions indicated do not solve the problem, refer to 
“Customer Services Directory (United States)” on 
page 19.
█Common problems
The unit does not work.• The safety device has been activated. Do the following:1. Press [ 1] on the main unit to turn the unit to standby 
mode. If the unit does not turn to standby mode,
– Press and hold the button for a minimum of  10 seconds. Or,
– Disconnect the AC power supply cord and reconnect.
2. Press [ 1] again to turn on the unit. If the problem 
persists, consult your dealer.
The display panel lights up  and changes continuously 
in standby mode.
• Press and hold [ 8] on the main unit to select “DEMO OFF”.
No operations can be done with the remote control.• Examine that the battery is installed correctly.
Sound is distorted or no sound.• Adjust the volume of the system.
• Turn off the system, determine and correct the cause, then 
turn on again. It can be caused by straining of the speakers 
through excessive volume or power, and when using the 
system in a hot environment.
A humming sound can be heard during playback.• An AC power supply cord or fluorescent light is near the cables. Keep other appliances and cords away from the 
cables of this system.
The sound level reduces.• The protection circuit has been activated due to the continuous use at high volume output. This is to protect the 
system and maintain the sound quality.
█Disc
Display not shown correctly.
Playback does not start.
• You have not put in the disc correctly. Put it in correctly.
• If the disc is dirty, then clean the disc.
• Replace the disc if it is scratched, warped, or non-standard.
• If there is condensation, then let the system dry for 1 to  2hours.
The total number of tracks displayed is incorrect.
The disc cannot be read.
Distorted sound is heard.
• You put in a disc that the system cannot play. Change to a playable disc.
• You put in a disc that has not been finalized.
█USB
The USB device or the contents in it cannot be read.• The format of the USB device or the contents in it are not  compatible with the system.
• USB devices with storage capacity of more than 32 GB  cannot work in some conditions.
Slow operation of the USB device.• Large content size or large memory USB device takes longer time to read.
█Bluetooth®
Pairing cannot be done.• Check the Bluetooth® device condition.
• The device is out of the 10 m (33 ft) communication range.  Move the device nearer to the system.
The device cannot be connected.• The pairing of the device was unsuccessful. Re-do pairing.
• The pairing of the device has been replaced. Re-do pairing.
• This system might be connected to a different device. Disconnect the other device and try pairing the device 
again.
The device is connected but audio cannot be heard 
through the system.
• For some built-in Bluetooth® devices, you have to set the 
audio output to “SC-AKX18” manually. Read the operating 
instructions of the device for details.
Sound from the device is interrupted.• The device is out of the 10 m (33 ft) communication range.  Move the device nearer to the system.
• Remove any obstacle between the system and the device.
• Other devices that use the 2.4 GHz frequency band  (wireless router, microwaves, cordless phones, etc.) are 
interfering. Move the device nearer to the system and 
distance it from the other devices.
• Select “MODE 1” for stable communication.
█Radio
Sound is distorted.• Use an optional outdoor antenna. The antenna should be  installed by a technician.
A beat sound is heard.• Turn off the TV or move it away from the system.
• Move cell phones away from the system if the interference is apparent.
SC-AKX18 P RQT9899-P EN.fm  Page 14  Monday, April 14, 2014  10:41 AM  
						

							15
RQT9899
█Main unit displays
“ADJUST CLOCK”• The clock is not set. Adjust the clock.
“ADJUST TIMER”• The play timer is not set. Adjust the play timer.
“AUTO OFF”• The system has not been used for 20 minutes and will turn off within a minute. To cancel, press any button.
“ERROR”• An incorrect operation was done. Read the instructions and try again.
“F61”• Examine and correct the speaker cords connection.
• Disconnect the USB device. Turn off the system and then turn on again.
“F70”• Examine the Bluetooth® connection.
• Disconnect the Bluetooth® device. Turn off the system and 
then turn on again.
“F76”• There is a problem with the power supply.
• Disconnect the AC power supply cord and consult your  dealer.
“F77”• Disconnect the AC power supply cord and consult your dealer.
“NODEVICE”• The USB device is not connected. Examine the connection.
“NO DISC”• You have not put in a disc.
“NO PLAY”
“UNSUPPORT”
• Examine the content. You can only play supported format.
• The system may have a problem. Turn off the system and then turn on again.
“NO TRACK”• There is no album or track in the USB device.
“PLAYERROR”• You played an unsupported MP3 file. The system will skip 
that track and play the next one.
“REMOTE 1”
“REMOTE 2”
• The remote control and the main unit are using different codes. Change the code of the remote control.
– When “REMOTE 1” is shown, press and hold [OK] and [ ] for a minimum of 4 seconds.
– When “REMOTE 2” is shown, press and hold [OK] and  [USB/CD] for a minimum of 4 seconds.
“TEMP NG”• The temperature protection circuit has been activated, and the system will turn off. Let the unit cool down before 
turning it on again.
• Check that the ventilation opening of the unit is not  obstructed.
• Ensure this unit is well ventilated.
“USB OVER CURRENT ERROR”• The USB device is using too much power. Disconnect the  USB device, turn off the system and then turn on again.
“VBR–”• The system cannot show the remaining play time for variable bit rate (VBR) tracks.
Remote control code
When other Panasonic equipment responds to the 
remote control of this system , change the remote control 
code for this system.
Preparation
Press [USB/CD] to select “CD”.
█To set the code to “REMOTE 2”
1Press and hold [USB/CD] on the main unit and 
[RADIO/AUX] on the remote control until 
“REMOTE 2” is shown.
2Press and hold [OK] and [USB/CD] for a minimum of 
4 seconds.
█To set the code to “REMOTE 1”
1Press and hold [USB/CD] on the main unit and 
[USB/CD] on the remote control until “REMOTE 1” 
is shown.
2Press and hold [OK] and [ ] for a minimum of 
4seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory content.
1Disconnect the AC power supply cord.
2While you press and hold [ 1] on the main unit, 
connect the AC power supply cord again.
Continue to press and hold the button until 
“––––––––” is shown.
3Release [ 1].
All the settings are set back  to the factory defaults.
It is necessary to reset the memory items.
ENGLISH
SC-AKX18 P RQT9899-P EN.fm  Page 15  Monday, April 14, 2014  10:41 AM  
						

							16
RQT9899
Specifications
█Amplifier section
RMS output power stereo modeFront Ch (both ch driven) 175 W per channel (4  Ω), 1 kHz, 30% THD
Total RMS stereo mode power 350 W (30% THD)
FTC output power stereo mode Front Ch (both ch driven) 80 W per channel (4  Ω), 50 Hz to 20 kHz, 1% THD
Total FTC stereo mode power 160 W
█Tuner, terminals section
Preset memory FM 30 stations
Frequency modulation (FM) Frequency range 87.9 MHz to 107.9 MHz (200 kHz step)
87.5 MHz to 108.0 MHz (100 kHz step)
Antenna terminals 75 Ω  (unbalanced)
Analog audio input Pin jack (1 system)
█Disc section
Disc played [8 cm (3″) or 12 cm (5 ″)]
CD, CD-R/RW (CD-DA, MP3 )
Pick up Wavelength 790 nm (CD)
 MPEG-1 Layer 3
█Bluetooth® section
Version Bluetooth® Ver. 2.1 + EDR
Class Class 2
Supported profiles A2DP, AVRCP, SPP
Operating frequency 2.4 GHz band, FH-SS
Operation distance 10 m (33 ft) line of sight
█USB section
USB port
USB standard USB 2.0 full speed
Media file format support MP3 (*.mp3)
USB device file system FAT12, FAT16, FAT32
USB port power 500 mA (max)
█Speaker section
Speaker unit(s)
Woofer 16 cm (6  ½″) cone type
Tweeter 6 cm (2  ⅜″) cone type
Impedance 4 Ω
Dimensions (W x H x D) 200 mm x 334 mm x 233 mm
(7 ¾″ x 13  ¼″ x 9 ¼ ″)
Mass (Weight) 3 kg (6.6 lbs)
█General
Power supply AC 120 V, 60 Hz
Power consumption 50 W
Dimensions (W x H x D) 230 mm x 335 mm x 243 mm
(9 ¼″ x 13  ¼″ x 9 ¾ ″)
Mass (Weight) 2.7 kg (6 lbs)
Operating temperature range 0°C to +40°C
(+32°F to +104°F)
Operating humidity range 35% to 80% RH (no condensation)
Note:
• Specifications are subject to change without notice. 
Mass (weight) and dimensions are approximate.
• Total harmonic distortion is measured by the digital 
spectrum analyzer.
Power consumption in standby mode
0.4 W (approximate)
Power consumption in standby mode
(With “BLUETOOTH STANDBY” set to “ON”) 0.5 W (approximate)
SC-AKX18 P RQT9899-P EN.fm  Page 16  Monday, April 14, 2014  10:41 AM  
						

							17
RQT9899
Spanish quick reference /
Referencia rápida en español
Conexiones
Conecte el cable de alimentación de CA sólo después 
de haber hecho todas las demás conexiones.
1Conecte la antena interior de FM.
Coloque la antena donde la recepción sea la mejor.
2Conecte las bocinas.
3Conecte el cable de alimentación de CA.
No use un cable de alimentación de CA de otro 
equipo.
Reproducción de medios
Reproducción básica
 CD   USB   BLUETOOTH 
Nota:
Dependiendo del dispositivo Bluetooth®, algunas operaciones 
pueden no funcionar.
Radio
Preparación
Pulse [RADIO/AUX] para seleccionar “FM”.
Sintonización manual
1Pulse [PLAY MENU] para seleccionar 
“TUNE MODE”.
2Pulse [ R, T ] para seleccionar “MANUAL” y 
después pulse [OK].
3Pulse [ 2/3 ] o [5 /6 ] para sintonizar la 
estación.
Para sintonizar automáticamente, pulse y mantenga 
pulsado el botón hasta que la frecuencia comience a 
cambiar rápidamente.
Cuando se esté recibiendo una emisión en estéreo se 
visualizará “STEREO”.
Presintonización de la memoria
Puede presintonizar hasta 30 emisoras de radio FM.
█Preconfiguración automática
1Pulse [PLAY MENU] para seleccionar “A.PRESET”.
2Pulse [ R, T ] para seleccionar “LOWEST” o 
“CURRENT” y después pulse [OK].
El sintonizador presintonizará en los canales, en 
orden ascendente, todas las emisoras que pueda 
recibir.
Para cancelar, pulse [ 8].
█Preconfiguración manual
1Pulse [PLAY MENU] para seleccionar 
“TUNE MODE”.
2Pulse [R, T ] para seleccionar “MANUAL” y 
después pulse [OK].
3Pulse [ 2/3 ] o [5 /6 ] para sintonizar la 
estación.
4Pulse [OK].
5Pulse [ R, T ] para seleccionar un número 
preconfigurado y después pulse [OK].
Realice los pasos 3 al 5 nuevamente para 
preconfigurar más estaciones.
La estación más reciente reemplazará cualquier 
estación que ocupe el mismo número 
preconfigurado.
█Selección de una emisora preconfigurada
1Pulse [PLAY MENU] para seleccionar 
“TUNE MODE”.
2Pulse [ R, T ] para seleccionar “PRESET” y después 
pulse [OK].
3Pulse [ 2/3 ] o [5 /6 ] para seleccionar una 
emisora preconfigurada.
Reproducir Pulse [ 4/9 ].
Detener Pulse [ 8]. USB Se memorizará la posición.
Se visualiza “RESUME”.
Pulse nuevamente para detener totalmente.
Pausar Pulse [ 4/9 ].
Pulse nuevamente para reanudar la 
reproducción.
Saltar Pulse [ 2/3 ] o [5 /6 ] para saltar 
pista.
 CD   USB Pulse [ R, T ] para saltar álbum MP3.
Buscar Pulse y mantenga pulsado [ 2/3 ]o 
[5 /6 ].
ESPAÑOL
SC-AKX18 P RQT9899-P EN.fm  Page 17  Monday, April 14, 2014  10:41 AM  
						

							18
RQT9899
Reloj y temporizadores
Configuración de la hora
Este es un reloj con un sistema de 12 horas.
1Pulse [SETUP] para seleccionar “CLOCK”.
2Pulse [R, T ] para configurar la hora y después 
pulse [OK].
Para revisar la hora
Pulse [SETUP] para seleccionar “CLOCK” y después 
pulse [OK].
El modo de espera , pulse [DISPLAY].
Nota:
Vuelva a poner en hora el reloj frecuentemente para mantener 
su exactitud.
Temporizador de apagado automático
El temporizador de apagado automático apagará el 
sistema después de la hora configurada.
1Pulse [SETUP] para seleccionar “SLEEP”.
2Pulse [R, T ] para seleccionar la configuración 
(en minutos) y después pulse [OK].
Para cancelar, seleccione “OFF”.
Nota:
• El tiempo restante siempre se muestra en la pantalla. La  pantalla cambia temporalmente cuando realiza otras 
operaciones.
• El temporizador para reproducción y de apagado  automático o el temporizador para grabación y de apagado 
automático pueden usarse al mismo tiempo.
• El temporizador de apagado automático siempre tiene  prioridad. Asegúrese de no configurar horas superpuestas.
SC-AKX18 P RQT9899-P EN.fm  Page 18  Monday, April 14, 2014  10:41 AM  
						

							19
RQT9899
Limited Warranty (ONLY FOR U.S.A.)
Panasonic Products Limited Warranty
Limited Warranty Coverage (For USA Only)If your product does not work properly because of a defect in 
materials or workmanship, Panasonic Corporation of North 
America (referred to as “the warrantor”) will, for the length of 
the period indicated on the chart below, which starts with the 
date of original purchase (“warranty period”), at its option 
either (a) repair your product with new or refurbished parts, 
(b) replace it with a new or a refurbished equivalent value 
product, or (c) refund your purchase price. The decision to 
repair, replace or refund will be made by the warrantor.
During the “Labor” warranty period there will be no charge for 
labor. During the “Parts” warranty period, there will be no 
charge for parts. This Limited Warranty excludes both parts 
and labor for non-rechargeable batteries, antennas, and 
cosmetic parts (cabinet). This warranty only applies to 
products purchased and serviced in the United States. This 
warranty is extended only to the original purchaser of a new 
product which was not sold “as is”.
Mail-In Service -- Online Repair Request
Online Repair RequestTo submit a new repair request and for quick repair status 
visit our Web Site at www.panasonic.com/repair.
When shipping the unit, carefully pack, include all supplied 
accessories listed in the Owner's Manual, and send it prepaid, 
adequately insured and packed well in a carton box.
When shipping Lithium Ion batteries please visit our Web Site
at www.panasonic.com/BatteryHandling
 as Panasonic is
committed to providing the most up to date information. 
Include a letter detailing the complaint, a return address and 
provide a daytime phone number where you can be reached. 
A valid registered receipt is required under the Limited 
Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, 
THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits And ExclusionsThis warranty ONLY COVERS failures due to defects in 
materials or workmanship, and DOES NOT COVER normal 
wear and tear or cosmetic damage. The warranty ALSO 
DOES NOT COVER damages which occurred in shipment, or 
failures which are caused by products not supplied by the 
warrantor, or failures which result from accidents, misuse, 
abuse, neglect, mishandling, misapplication, alteration, faulty 
installation, set-up adjustments, misadjustment of consumer 
controls, improper maintenance, power line surge, lightning 
damage, modification, introduction of sand, humidity or 
liquids, commercial use such as hotel, office, restaurant, or 
other business or rental use of the product, or service by 
anyone other than a Factory Service Center or other 
Authorized Servicer, or damage that is attributable to acts of 
God. THERE ARE NO EXPRESS WARRANTIES EXCEPT AS 
LISTED UNDER “LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR 
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE 
OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF 
THIS WARRANTY.
(As examples, this excludes damages for lost time, travel to 
and from the servicer, loss of or damage to media or images, 
data or other memory or recorded content. The items listed 
are not exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING 
THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO 
THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of 
incidental or consequential damages, or limitations on how 
long an implied warranty lasts, so the exclusions may not 
apply to you.
This warranty gives you specific legal rights and you may also 
have other rights which vary from state to state. If a problem 
with this product develops during or after the warranty period, 
you may contact your dealer or Service Center. If the problem 
is not handled to your satisfaction, then write to the 
warrantor’s Consumer Affairs Department at the addresses 
listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY 
THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
As of April 2014
Product or Part Name Parts Labor
CD Stereo System 1 Year 1 Year
All included Accessories (Except 
Non-Rechargeable Batteries)
90 Days Not 
Applicable
Only Non-Rechargeable Batteries 10 Days Not  Applicable
Customer Services Directory (United States)
Obtain Product Information and Operating Assistance; 
locate your nearest Dealer or Service Center; purchase 
Parts and Accessories; or make Customer Service and 
Literature requests by visiting our Web Site at: 
http://www.panasonic.com/support
or, contact us via the web at:
http://www.panasonic.com/contactinfo
For hearing or speech impaired TTY users, TTY: 
1-877-833-8855
Accessory Purchases (United States)
Purchase Parts, Accessories and Owner’s Manual online for 
all Panasonic Products by visiting our Web Site at: 
http://www.pstc.panasonic.com
or, send your request by E-mail to: 
[email protected]
You may also contact us directly at: 
1-800-237-9080 (Fax Only) 
(Monday-Friday 9am-9pm EST) 
Panasonic National Parts Center 
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, and American 
Express.)
For hearing or speech impaired TTY users, TTY: 
1-866-605-1277
SC-AKX18 P RQT9899-P EN.fm  Page 19  Monday, April 14, 2014  10:41 AM  
						

							P
Two Riverfront Plaza, Newark,
New Jersey 07102-5490
http://www.panasonic.com
© Panasonic Corporation 2014
Printed in MalaysiaRQT9899-P
L0414LC0
EnSp
SC-AKX18 P RQT9899-P EN.fm  Page 20  Monday, April 14, 2014  10:41 AM