Panasonic Cd Stereo System Sc-ak640 Operating Instructions

							
11
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK
ENGLISH
2Press [0 OPEN] for DECK 1 or [OPEN  0] for DECK 2 
and insert the cassette.
Insert with the side to be played facing towards you 
and the exposed tape facing down. Close the holder by 
hand.
Front 
side
3Press [ 3, TAPE] to start play.
To A c t i o n
stop tape playback Press [ 7, STOP].
fast-for ward and 
rewind Press [
4 / REW /  ]  or  [  / FF /  ¢].
select between 
loaded decksPress [DECK 1/2] (remote control : 
[PLAY MODE]).
Note: Tape playback is momentarily interrupted if you open the other 
deck.
  Tapes exceeding 100 minutes are thin and can break or get caught  in the mechanism.
 Tape slack can get caught up in the mechanism and should be  wound up before the tape is played.
  Endless tapes can get caught up in the deck’s moving parts if used  incorrectly.
Reco rd in gRecording
Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but this 
unit will not be able to record or erase them correctly.
Preparation
Wind up the leader tape so recording can begin 
immediately.
1Press [OPEN  0] for DECK 2 and insert the cassette 
to be recorded.
Insert with the side to be recorded facing towards you 
and the exposed tape facing down.
2Select the source to be recorded.
Radio recording:
Tune in the station. ( \ page 12)
Disc recording:
➀  Insert the disc (s) you want to record. Press [ 6, CD] and then [ 7, STOP].➁  Prepare the desired disc recording mode.
To A c t i o n
record 
programmed 
tracks
Perform steps 2 to 4 in “Program play” 
(\  page 8).
 Perform steps 3 to 6 in “Program play” 
(\  page 8). By remote control only
record 
speci c 
discs/tracks 
1)  Press [DISC] and then [1] ~ [5] to select 
the disc.
Ensure disc is stopped.
2) Press [PLAY MODE] to select the desired  mode ( \ page 7).
3) 
   For 1-ALBUM mode and 1-SONG mode:
  Press [ALBUM ( or )] to select the 
album.
 
    For 1-SONG mode: 
 Press [ 4, REW /  ] or [ ¢,   / FF]  to 
select the track.
Tape-to-tape recording:➀ Press [ 3, TAPE] and then [ 7, STOP].➁ Press [ 0 OPEN] for DECK 1 and insert the cassette 
to record.
3Press [ ¶, REC] to start recording.
O th er b asic  o pera tio nsOther basic operations
To A c t i o n
stop recording Press [ 7, STOP].
record on the other 
side of the tape Turn the cassette over and press [
¶, REC].
erase a recorded 
sound 1) Press [
3, TAPE] and then [ 7, STOP].
2) Insert the recorded cassette into  DECK 2. Ensure there is no cassette in 
DECK 1.
3) Press [ ¶, REC].
Note:  Changes to volume and sound adjustments quality do not affect 
recording.
  You cannot open DECK 1 while recording.
  You cannot fast-forward or rewind one deck while recording with  the other.
Era su re  p re ven tio nErasure prevention
The illustration shows how to remove the tabs to prevent 
recording. To record on the tape again, cover as shown.
Side A
Tab for side A
Tab for side B
To re-record
Normal cassette
Adhesive tape
Cassette tape – Play and record (Continued)
R Q TV 0071-P _1E N .in dd   1 1RQTV0071-P_1EN.indd   1112/2 2/0 5   1 1:0 0:2 9  A M12/22/05   11:00:29 AM 
						

							12
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK ENGLISH
FM allocation settingFM allocation setting
By main unit only
This system can also receive FM broadcasts allocated in 
0.1 MHz steps.
To change the step to 0.1 MHz
1Press and hold [TUNER, BAND].
After a few seconds the display changes to a  ashing 
display of the current minimum frequency.
2Continue to hold down [TUNER, BAND].
  When the minimum frequency changes, release the 
button. To return to the original step, repeat the above 
steps.
  After changing the setting, previously preset frequency 
will be cleared.
Memory presetMemory preset
Up to 15 stations each can be set in the FM and AM bands.
Preparation
Press [TUNER, BAND] to select “FM” or “AM”.
Automatic presettingAutomatic presetting
1Tune to the frequency where pre-setting is to begin.
2Press and hold [PROGRAM] to start presetting.
The tuner presets all the stations it can receive into the 
channels in ascending order. When  nished, the last station 
memorized is tuned in.
Manual presettingManual presetting
1Press [PLAY MODE] to select “MANUAL”.
2Press [4, REW / ] or [¢,   / FF] to tune to the 
required station.
3Press [PROGRAM].
4Press the numeric buttons to select a channel.
For channels 10 to 15 press [h10], then the two digits.
The station occupying a channel is erased if another 
station is preset in that channel.
Selecting a preset stationSelecting a preset station
Press the numeric buttons to select the channel.
OR
1Press [PLAY MODE] to select “PRESET”.
2Press [4, REW /  ] or [¢,   / FF] to select the 
channel.
Numeric 
buttons
Manual tuningManual tuning
1Press [TUNER, BAND] to select “FM” or “AM”.
2Press [PLAY MODE] to select “MANUAL”.
3Press [4, REW / ] or [¢,   / FF] to select the 
frequency of the required station.
 “
” is displayed when a stereo FM broadcast is being 
received.
 “TUNED” is displayed when a radio station is tuned.
To tune automatically
Press and hold [4, REW /  ] or [¢,   / FF]  until  the 
frequency starts changing rapidly. The unit begins auto 
tuning, stopping when it  nds a station.
  Auto tuning may be interrupted when there is excessive 
interference.
  To cancel auto tuning, press [4, REW /  ] or 
[¢,   / FF]  once  again.
To improve FM sound qualityTo improve FM sound quality
Press and hold [PLAY MODE] to display “MONO”.
To cancel
Press and hold [PLAY MODE] again until “MONO” 
disappear.
  MONO is also canceled if the frequency is changed.
  Turn off “MONO” for normal listening.
Radio
RQTV0071-P_1EN.indd   12RQTV0071-P_1EN.indd   1211/21/05   9:11:10 AM11/21/05   9:11:10 AM 
						

							
13
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK
ENGLISH
4Repeat steps 2 to 3 to set the finishing time.
Finish time
To activate the timer
5Press and hold [– ˚PLAY/REC] to turn on your desired 
timer.
˚  PLAY
no display (off)
˚  REC
➞
6Press [ y] to turn off the unit.
The unit must be off for the timers to operate.
O th er b asic  o pera tio nsOther basic operations
To A c t i o n
change the 
settings Repeat steps 1 to 4 and 6 (
\ see left and 
above).
change the 
source or 
volume 1)  Press and hold [ – 
˚PLAY/ REC] to clear the 
timer indicator from the display.
2)  Make changes to the source or volume.
3)  Do steps 5 to 6 (
\ see above).
check the 
settings Press and hold [ – CLOCK/TIMER] successively 
to select 
˚PLAY or  ˚REC.
cancel  Press and hold [ –  ˚PLAY/ REC] to clear the 
timer indicators from the display.
If you use the unit after the timers are set
After using, check that the correct tape/disc are loaded 
before turning the unit off.
Note:
  The play timer will start at the preset time with volume increasing  gradually to preset level.
  The record timer will start 30 seconds before the set time with the  volume muted.
  The timer comes on at the set time everyday if the timer is on.
  The unit must be in the standby mode for the timer to function.
  If you turn the unit off and on again while a timer is functioning, the   nish time setting will not be activated.
  If MUSIC PORT is selected as the source when the timer comes on,  the system turns on and engages MUSIC PORT as the source. If 
you wish to playback or record from the portable audio equipment, 
just activate the equipment’s play mode and increase the volume. 
(See the portable audio equipment’s instruction manual.)
Settin g t h e c lo ckSetting the clock
This is a 12-hour clock.
1Press and hold [– CLOCK/TIMER] to select “CLOCK”.
Each time you press and hold the button:
➞
CLOCK
˚ PLAY
Original display
˚ REC
➞
2(Within 8 seconds or so)
Press [ 4, REW /  ] or [ ¢,   / FF] to set the time.
3Press and hold [– CLOCK/TIMER] to finish setting the 
time.
Displaying the clockPress and hold [ – CLOCK/TIMER] once when the unit is on or 
in standby mode.
The time is displayed for a few seconds.
Note:
Reset the clock regularly to maintain accuracy.
U sin g t h e p la y o r r e c o rd  t im erUsing the play or record timer
You can set the timer to come on at a certain time to wake 
you up (play timer) or to record from the radio or music port 
source (record timer).
Play timer and record timer cannot be used together.
Turn the unit on and set the clock.
Timer Action
Play timer Prepare the music source you want to listen to; 
cassette (DECK 2 has the priority), disc number 
(1~5), radio or music port source, and set the 
volume.
Record 
timer Check the cassette’s erasure prevention tabs 
(
\ page 11), insert the cassette in DECK 2 and 
tune to the radio station (\ page 12) or select the 
music port source (\ page 15).
1Press and hold [– CLOCK/TIMER] to select the timer 
function.
Each time you press and hold the button:
➞
CLOCK
˚
 PLAY
Original display
˚ REC
➞
˚ PLAY : to set the play timer
˚ REC  : to set the record timer
(Proceed to the next step 
within 8 seconds)
2Press [ 4, REW /  ] or [ ¢,   / FF] to set the 
starting time.
Record timer indicator Play timer indicator
Start time
3Press and hold [– CLOCK/TIMER] to confirm.
Timer
R
Q TV 0071-P _1E N .in dd   1 3RQTV0071-P_1EN.indd   1312/6 /0 5   1 0:2 6:3 6 A M12/6/05   10:26:36 AM 
						

							
14
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK ENGLISH
MUSIC 
PORT 
jack
Usin g t h e s le ep  t im erUsing the sleep timer
This function enables you to turn off the unit automatically 
after the set time.
Press [SLEEP] to select your desired time.
SLEEP 30 SLEEP 60 SLEEP 90
SLEEP 120
SLEEP OFF
Sleep timer indicator
To cancel
Press [SLEEP] to select “SLEEP OFF”.
Changing the remaining time
Press [SLEEP] to show the remaining time and press 
[SLEEP] again to select your desired time.
Note:
  The play and sleep timer or the record and sleep timer can be used 
together.
  The sleep timer always has priority. Be sure not to overlap timer  settings.
  The sleep timer turns off when you perform the record function.
Sound adjustment
S ele ctin g s o und e ffe ctsSelecting sound effects
P re set E QPreset EQ
Press [PRESET EQ] repeatedly to select your desired 
setting.
➞
HEAVY SOFT
CLEAR
➞ VOCAL
➞
FLAT (off) HALL LIVE
➞➞
DISCO
➞
Setting Effect
HEAVY Adds punch to rock
SOFT For background music
CLEAR Clari es higher frequencies
VOCAL Adds gloss to vocal
DISCO Produces sound with the same kind of lengthy 
reverberations heard at a disco
LIVE Makes vocals more alive
HALL Adds an expansiveness to the sound to produce the  atmosphere of a great concert hall
FLAT No effect
E nhan cin g t h e b ass s o undEnhancing the bass sound
You can enhance low-frequency sound so that heavy bass 
sound can be heard clearly, even if the acoustics of your 
room are not optimal.
To  a c t i v a t e
Press  [H.BASS].
To  c a n c e l
Press [H.BASS] again.
Note:
The actual effect depends on the disc.
B oostin g t h e s u bw oofe rBoosting the subwoofer
Press [S.WOOFER] (main unit: [SUBWOOFER]) repeatedly 
to select your desired setting.
➞
MID (medium)
(off) MAX (high)
Note:
This function is not applicable when a headphone is connected.
Timer (Continued)
R Q TV 0071-P _1E N .in dd   1 4RQTV0071-P_1EN.indd   1411/2 8/0 5   1 1:2 7:2 0 A M11/28/05   11:27:20 AM 
						

							
15
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK
ENGLISH
Connectin g t o  a  p orta b le  a u dio  e q uip m en tConnecting to a portable audio equipment
This feature enables you to enjoy music from a portable 
audio equipment.
Portable audio equipment 
(not included)
Audio cord 
(not included)
P la yin g f r o m  a  p orta b le  a u dio  e q uip m en tPlaying from a portable audio equipment
Switch off the equalizer function (if there is any) of the 
portable audio equipment before you plug into the MUSIC 
PORT jack. Otherwise, sound from the speaker may be 
distorted.
1Plug the audio cord into the MUSIC PORT jack and 
press [MUSIC P.].
2Play the portable audio equipment. (See the portable 
audio equipment’s instruction manual.)
R eco rd in g f r o mRecording from a   a p orta b le  a u dio  portable audio eq uip m en tequipment
1Press [MUSIC P.].
2Play the portable audio equipment.
3Press [ ¶, REC] on the main unit to start recording.
Note:
All peripheral components and cables are sold separately.
Product Service
1. Damage requiring service  - The unit should be serviced 
by qualifi ed service personnel if:
  (a) The AC power supply cord or the plug has been  damaged; or
  (b)  Objects or liquids have gotten into the unit; or
  (c)  The unit has been exposed to rain; or
  (d) The unit does not operate normally or exhibits a  marked change in performance; or
  (e)  The unit has been dropped or the cabinet damaged.
2. Servicing  - Do not attempt to service the unit beyond that 
described in these operating instructions. Refer all other 
servicing to authorized servicing personnel.
3. Replacement  parts  - When parts need replacing ensure 
the servicer uses parts specifi ed by the manufacturer or 
parts that have the same characteristics as the original 
parts. Unauthorized substitutes may result in fi re, electric 
shock, or other hazards. 4. Safety check
 - After repairs or service, ask the servicer to 
perform safety checks to confi rm that the unit is in proper 
working condition.
The servicer will require all components to service your 
system.
Therefore, should service ever be necessary, be sure to 
bring the entire system.
Product information
For product information or assistance with product 
operation:
In the U.S.A. , refer to “Customer Services Directory” on 
page 18.
In Canada , contact the Panasonic Canada Inc. Customer 
Care Centre at 905-624-5505, or visit the website 
(www.panasonic.ca), or an authorized Servicentre closest 
to you.
Maintenance
I f  t h e s u rfa ces a re  d ir tyIf the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
•   Never use alcohol, paint thinner or benzine to clean this 
unit.
•    Before using chemically treated cloth, read the instructions  that came with the cloth carefully.
For a  c le an er c ris p er s o und ( c assette  d eck)For a cleaner crisper sound (cassette deck)
Clean the heads regularly to assure good quality playback 
and recording. Use a cleaning tape (not included).
When moving the unit
1Remove all discs.
2Press [ y/ I, POWER] to turn the unit off.
3Disconnect the AC power supply cord.
External unit
RQ TV 0071-P _1E N .in dd   1 5RQTV0071-P_1EN.indd   151 2/8 /0 5   8 :2 0:3 9  A M12/8/05   8:20:39 AM 
						

							16
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK ENGLISH
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the 
remedies indicated in the chart do not solve the problem, refer to the “Customer Services Directory” on page 18 if you 
reside in the U.S.A., or refer to the “Product information” on page 15 if you reside in Canada.
Reference pages are shown as black circled numbers 4.
Common problems
Although the unit is in standby mode, the 
display lights up and changes continuously.Turn off the demo function. 5
If you set the clock, demo function will be turned off automatically. $
No sound.
Sound stops.Turn the volume up.
Switch off the unit, determine and correct the cause, then switch the unit on. Causes include 
shorting of the positive and negative speaker wires, straining of the speakers through excessive 
volume or power, and using the unit in a hot environment.
Sound is un xed, reversed or comes from 
one speaker only.Check the speaker connections. 4
Humming heard during play.
An AC power supply cord or  uorescent light is near the cables. Keep other appliances and cords 
away from this unit’s cables.
“ERROR” is displayed.
Incorrect operation performed. Read the instructions and try again.
“– – : – –” appears on the display at 
standby mode.You plugged the AC power supply cord in for the  rst time or there was a power failure recently.
Set the time. $
“F61” is displayed.
Check and correct the speaker cords connection. 4
If this does not  x the problem, there is a power supply problem. Consult the dealer.
Listening to the radio
Noise is heard.The stereo indicator  ickers or doesn’t light.Sound is distorted.Use an outdoor antenna. 4
A beat sound is heard.
Turn the TV off or separate it from the unit.
A low hum is heard during AM broadcast.
Separate the antenna from other cables and cords.
When there is a television set nearby
The picture on the T V disappears or 
stripes appear on the screen.The location and orientation of the antenna are incorrect. If you are using an indoor antenna, 
change to an outdoor antenna.
The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from the unit.
Using the cassette deck
Poor quality sound.
Clean the heads. &
Recording is not possible.
If the erasure prevention tabs have been removed, cover the holes with adhesive tape. 
Playing discs
The display is wrong or play won’t start.
The disc may be upside down. !
Wipe the disc.
Replace the disc if it is scratched, warped, or non-standard.
Condensation may have formed inside the unit due to a sudden change in temperature. Wait for 
about an hour for it to clear and try again.
The total number of tracks displayed 
differs each time the same disc is inserted.
Unusual sound is heard.The disc may be scratched, or its data may be defective. Replace the disc. 
CD -RW cannot be read.
The disc was incompletely formatted. Use the recording equipment to fully format the disc before 
recording.
“VBR–” is displayed instead of the 
remaining play time.The unit cannot display the remaining play time for variable bit rate (VBR) tracks.
Disc trays
Disc tray(s) cannot open.
“CHGR ERR ” is displayed.Press [y/ I, POWER] to release the jammed tray(s) as the unit will switch off. Switch it on again and 
the tray(s) will initialize to the previous tray(s) condition.
If this still does not  x the problem, please consult the dealer.
Remote control
Remote control doesn’t work.
Check that the batteries are inserted correctly. 5
Replace the batteries if they are worn. 
Memory reset ( Initialization)When the following situations occur, refer to the instructions below to reset the memory:
 There is no response when buttons are pressed.
 You want to clear and reset the memory contents.
To reset memory
1 Disconnect the AC power supply cord. (Wait at least 3 minutes before proceeding to step 2 )
2 While pressing and holding down [y/ I, POWER] on the main unit, reconnect the AC power supply cord.
“– – – – – – – – –” appears on the display.
3 Release [y/ I, POWER] .
All the settings are returned to the factory preset.
You will need to reset the memory items.
RQTV0071-P_1EN.indd   16RQTV0071-P_1EN.indd   1611/21/05   9:11:32 AM11/21/05   9:11:32 AM 
						

							
17
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK
ENGLISH
AMPLIFIER SECTIONFTC Output power
 THD 10%
  100 Hz to 3 kHz
    (Low channel-both channels driven)  75 W per channel (3 Ω)
  3 kHz to 12 kHz
    (High channel-both channels driven)  75 W per channel (3  Ω)
  40 Hz to 100 Hz
    (Subwoofer channel)  150 W (8  Ω)
  Total FTC power  450 W
RMS output power
 THD 10%
 1 kHz
    (Low channel-both channels driven)  90 W per channel (3  Ω)
 10 kHz
    (High channel-both channels driven)  90 W per channel (3  Ω)
 60 Hz
    (Subwoofer channel)  180 W (8  Ω)
  Total output power  540 W
FM/AM TUNER, TERMINALS SECTIONPreset station  FM 15 stations
      AM 15 stations
Frequency Modulation (FM)
 Frequency range   87.9 to 107.9 MHz (200 kHz steps)
      87.5 to 108.0 MHz (100 kHz steps)
  Sensitivity   4.0 µV (IHF)
  S/N 26
 dB  2.2 µV
  Antenna terminal(s)  75  Ω (unbalanced)
Amplitude Modulation (AM)
 Frequency range   520 to 1710 kHz (10 kHz steps)
 Sensitivity
   S/N 20 dB (at 1000 kHz)  560 µV/m
Music Port input jack
  Terminal   Stereo, 3.5 mm (
1/8˝) jack
  Sensitivity   100 mV, 4.7 k Ω
Phone jack
  Terminal   Stereo, 3.5 mm (
1/8˝) jack
CASSETTE DECK SECTIONTrack system   4 track, 2 channel
Heads
  Record/playback   Solid permalloy head
  Erasure   Double gap ferrite head
Motor   DC servo motor
Recording system   AC bias 100
 kHz
Erase system   AC erase 100 kHz
Tape speed  4.8 cm/s (17/8 ips)
Overall frequency response (+3 dB, –6 dB) at DECK OUT
  NORMAL   35 Hz to 14 kHz
S/N Ratio   50 dB (A weighted)
Wow and   utter 0.18% (WRMS)
Fast forward and rewind time
      Approx. 120 seconds with C-60 cassette tape
DISC SECTIONDisc played [8 cm (3 ) or 12 cm (5 )]
 (1) CD-Audio (CD-DA)
  (2)  CD-R/RW (CD-DA, MP3, WMA formatted disc)
 (3) MP3/WMA
Bit rate
  MP3, WMA   32 kbps to 320 kbps
Sampling frequency
  MP3/WMA   32 kHz, 44.1 kHz, 48 kHz
  CD-DA  44.1 kHz
Decoding   16 bit linear
Digital   lter 8 fs
D/A converter   MASH (1 bit DAC)
Pick up
  Wavelength  780 nm
  Beam Source  Semiconductor laser
Audio output (Disc)
  Number of channels   2(Stereo) (FL, FR)
Speci cations
SPEAKER SECTIONFront speakers SB-AK640Type  3 way, 3 speaker system (Bass refl ex)
Speaker(s) 
  Woofer   16 cm (6
1/2˝) cone type
  Tweeter  6 cm (23/8˝) cone type
  Super tweeter  Piezo type
Impedance 
  HIGH  3  Ω
  LOW  3  Ω
Input power (IEC)
  HIGH   105 W (Max)
  LOW   105 W (Max)
Output sound pressure level   83 dB/W (1.0 m)
Cross over frequency   2 kHz, 10 kHz
Frequency range   37 Hz to 23 kHz (–16 dB)
      44 Hz to 22 kHz (–10 dB)
Dimensions (WxHxD)   247 x 330 x 221 mm
    (9
23/32˝ x 13˝ x 811/16˝)
Mass  3.0 k g (6.6 Ib.)
Subwoofer SB-WAK640Type   1 way, 1 speaker system (Bass refl ex)
Speaker(s) 
  Subwoofer   16 cm (6
1/2˝) cone type
Impedance  8  Ω
Input power (IEC)  180
 W (Max)
Output sound pressure level   80 dB/W (1.0 m)
Frequency range   40 Hz to 220 Hz (–16 dB)
      45 Hz to 180 Hz (–10 dB)
Dimensions (WxHxD)   248 x 330 x 256 mm
    (9
3/4˝ x 13˝ x 103/32˝)
Mass  3.6 k g (7.9 Ib.)
GENERALPower supply   AC 120 V, 60 Hz
Power consumption  132 W
Dimensions (WxHxD)   250 x 330 x 343 mm
    (9
27/32˝ x 13˝ x 131/2˝)
Mass  6.6 k g (14.6 Ib.)
Operating temperature range   +5 to +35 °C (+41 to +95°F)
Operating humidity range   5 to 90 % RH (no condensation)
Power consumption in standby mode: 0.28 W
Note:
1. Specifi cations are subject to change without notice.
  Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum  analyzer.
3. The labels “HIGH” and “LOW” on the rear of the speakers refer to  High frequency and Low frequency.
RQ TV 0071-P _1E N .in dd   1 7RQTV0071-P_1EN.indd   1712/7 /0 5   1 0:2 5:4 5 A M12/7/05   10:25:45 AM 
						

							18
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK ENGLISH
Limited Warranty (ONLY FOR U.S.A.)
Panasonic Consumer Electronics Company, 
Division of Panasonic Corporation of North America
One Panasonic Way Secaucus, New Jersey 07094Panasonic Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5 
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic Audio Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or 
workmanship, Panasonic Consumer Electronics Company or Panasonic 
Puerto Rico, Inc. (collectively referred to as “ the warrantor” ) will, for the 
length of the period indicated on the chart below, which starts with the 
date of original purchase ( “ warrant y period” ), at its option either (a) repair 
your product with new or refurbished parts, or (b) replace it with a new or 
a refurbished product. The decision to repair or replace will be made by 
the warrantor.
Product of Part Name Parts Labor
Audio Products (except items listed 
below)One (1) year One (1) year
USB Reader-Writer, Personal 
Computer Card Adapters
(in exchange for defective item)One (1) year Not 
Applicable
Accessories: Headphones, 
Cartridges, Microphones, AdaptersNinety (90) 
daysNinety (90) 
days
Rechargeable Batteries, 
DVD-R /-RAM Discs (in exchange for 
defective item)Ten (10) days Not 
Applicable
SD Memory Cards, Rechargeable 
Battery Packs (in exchange for 
defective item)Ninety (90) 
daysNot 
Applicable
During the “Labor” warranty period there will be no charge for labor. 
During the “Parts” warranty period, there will be no charge for parts. You 
must carry-in or mail-in your product during the warranty period. If non-
rechargeable batteries are included, they are not warranted. This warranty 
only applies to products purchased and ser viced in the United States or 
Puerto Rico. This warranty is extended only to the original purchaser of a 
new product which was not sold “as is”. A purchase receipt or other proof 
of the original purchase date is required for warranty ser vice.Carry-In or Mail-In Service
For Carry-In or Mail-In Ser vice in the United States call 1-800-211-PANA 
(1-800-211-7262) or visit Panasonic web site: http://w w w.panasonic.com
For assistance in Puerto Rico call Panasonic Puerto Rico, Inc. 
(787) -750-4300 or fax (787) -768-2910.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or 
workmanship, and DOES NOT COVER normal wear and tear or cosmetic 
damage. The warranty ALSO DOES NOT COVER damages which occurred 
in shipment, or failures which are caused by products not supplied by 
the warrantor, or failures which result from accidents, misuse, abuse, 
neglect, mishandling, misapplication, alteration, faulty installation, set-up 
adjustments, misadjustment of consumer controls, improper maintenance, 
power line surge, lightning damage, modi cation, or commercial use 
(such as in a hotel, of ce, restaurant, or other business), rental use of 
the product, ser vice by anyone other than a Factory Ser vicenter or other 
Authorized Ser vicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER 
“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE 
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM 
THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF 
THIS WARRANTY. (As examples, this excludes damages for lost time, 
travel to and from the ser vicer, loss of media or images, data or other 
memory content. The items listed are not exclusive, but are for illustration 
only.) ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE 
WARRANT Y OF MERCHANTABILIT Y, ARE LIMITED TO THE PERIOD 
OF THE LIMITED WARRANT Y.
Some states do not allow the exclusion or limitation of incidental or 
consequential damages, or limitations on how long an implied warranty 
lasts, so the exclusions may not apply to you.
This warranty gives you speci c legal rights and you may also have 
other rights which vary from state to state. If a problem with this product 
develops during or after the warranty period, you may contact your dealer 
or Ser vicenter. If the problem is not handled to your satisfaction, then 
write to the warrantor’s Consumer Affairs Department at the addresses 
listed for the warrantor.
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED 
WARRANTY ARE YOUR RESPONSIBILITY.
Customer Services DirectoryCustomer Services Directory
Obtain Product Information and Operating Assistance; locate your nearest Dealer or Servicenter; purchase Parts and Accessories; 
or make Customer Service and Literature requests by visiting our Web Site at:
http://www.panasonic.com/consumersupportor, contact us via the web at:
http://www.panasonic.com/contactinfoYou may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
For hearing or speech impaired TTY users, TTY: 1-877-833-8855
Accessory PurchasesAccessory Purchases
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:
http://www.pasc.panasonic.comor, send your request by E-mail to:
[email protected] may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday-Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY: 1-866-605-1277
Service in Puerto RicoService in Puerto Rico
Panasonic Puerto Rico, Inc. 
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 
Phone (787)750-4300, Fax (787)768-2910
RQTV0071-P_1EN.indd   18RQTV0071-P_1EN.indd   1811/21/05   9:11:34 AM11/21/05   9:11:34 AM 
						

							19
RQT8043
RQTV0071
LANG - 5 LANG - 4 FRANÇAIS DANSK
ENGLISH
Limited Warranty (ONLY FOR CANADA)
Panasonic Canada Inc.
PANASONIC/TECHNICS PRODUCT – LIMITED WARRANTY
Pana sonic Canada Inc. warrant s this pro duc t to b e free from defe c t s in material and wor k manship and agrees to reme dy any 
such defect for a period as stated below from the date of original purchase.
Technics Audio Product One (1) year, parts and labour
Panasonic Audio & DVD Product One (1) year, parts and labour
Accessories including rechargeable batteries Ninety (90) days
In-home Service will be carried out only to locations accessible by roads and within 50 km of an authorized Panasonic 
service facility.
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to any product which has been improperly installed, 
subjected to usage for which the product was not designed, misused or abused, damaged during shipping, or which has 
been altered or repaired in any way that affects the reliability or detracts from the performance, nor does it cover any product 
which is used commercially. Dry cell batteries are also excluded from coverage under this warranty.
This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of date of original 
purchase is required before warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING 
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL 
DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the 
exclusion of implied warranties, so the above limitations and exclusions may not be applicable.
WARRANTY SERVICE
FOR PRODUCT OPERATION ASSISTANCE, please contact:
Our Customer Care Centre:  Telephone #: (905) 624-5505
 1- 8 0 0 # : 1- 8 0 0 - 561- 550 5
  Fax #:  (905) 238-2360
  Email link:  “Contact Us” on www.panasonic.ca
FOR PRODUCT REPAIRS, please locate your nearest Authorized Servicentre at www.panasonic.ca:
Link : “Servicentres
TM locator” under “Customer support”
Panasonic Factory Service:
Richmond British Columbia Mississauga Ontario
Panasonic Canada Inc.
12111 Riverside Way
Richmond BC    V6W 1K8
Te l :  ( 6 0 4 )  2 7 8 - 4 2 11
Fa x: (604) 278-5627 Panasonic Canada Inc.
5770 Ambler Drive
Mississauga ON    L4W 2T3
Te l :  ( 9 0 5 )  6 2 4 - 8 4 47
Fa x: (905) 238-2418
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the original carton.
Include details of the defect claimed, and proof of date of original purchase.
RQTV0071-P_1EN.indd   19RQTV0071-P_1EN.indd   1911/21/05   9:11:35 AM11/21/05   9:11:35 AM 
						

							20
RQT8043
RQTV0071
ESPAÑOL LANG - 4
FRANÇAIS
DANSK
ENGLISH
(L) (R)
Preparativos iniciales
4 Conecte el cable de alimentación de CA
Para su referencia
Para ahorrar energía cuando no utiliza el aparato durante 
mucho tiempo, desenchúfelo de la toma de CA.
Después de enchufar el aparato tendrá que reponer algunos 
elementos de la memoria.Nota:El cable de alimentación de CA incluido es para ser usado con 
este aparato solamente.
No lo utilice con otro equipo.
PasoPaso  11 - Conexiones - Conexiones
Conecte el cable de alimentación de CA sólo después de haber hecho todas las demás conexiones.
Referencia  Las conexiones del equipo descritas sirven en concepto de ejemplo.
  Los equipos periféricos y los cables opcionales se venden por separado si no está indicado de otro modo.
PPasoaso 2 2 - Introducción de pilas en el mando a distancia
R6/LR6, AA■ Pilas
  Inserte los polos (+ y –) de la forma que se indica en el mando a distancia.
  Retire las pilas si no va a utilizar el mando a distancia durante un periodo de 
tiempo largo. Guárdelas en un lugar fresco y oscuro.
  Reemplace las pilas si el aparato no responde al mando a distancia a pesar 
de utilizarlo cerca del panel delantero.
  No utilice baterías recargables.
  Un mal manejo de pilas en el control remoto puede provocar fugas 
electrolíticas, que pueden provocar fuego.
  Si las pilas tienen fugas de electrólito, consulte a su distribuidor.
  Si el electrólito entra en contacto con cualquier parte de su cuerpo, lave la 
parte afectada con agua abundante.
No:
  mezcle nunca pilas viejas y nuevas.
  utilice nunca pilas de diferentes tipos a la vez.
  caliente nunca las pilas ni las exponga a las llamas.
  desmonte nunca las pilas ni las cortocircuite.
  intente nunca recargar pilas alcalinas o de manganeso.
  utilice nunca pilas cuya cubierta protectora esté levantada.
  ponga nunca objetos pesados encima del mando a distancia.
  derrame nunca líquidos sobre el mando a distancia.
■ Utilización
  Diríjalo al sensor del mando a distancia, evitando los obstáculos, desde 
una distancia máxima de 7 m (23 pies) directamente frente al aparato.
  Consulte la página 22 para ver la posición del sensor de la señal del 
mando a distancia.
3 Conecte la antena interior de FM.
Fije la antena donde la recepción sea major.
Cinta 
adhesiva
2 Conecte la antena de cuadro de AM.
Ponga la antena 
en posición vertical 
sobre su base.
1 Conecte los cables de los altavoces.
Gris (+)
Azul (–) Gris
AzulNegro Rojo
Rojo (+)
Negro (–)
Conecte de la 
misma forma en el 
lado izquierdo (L)
Rojo (+)
Negro (–)
(SB-WAK640)Altavoz de 
subgraves
RQTV0071-P_2SP.indd   20RQTV0071-P_2SP.indd   2012/6/05   4:45:23 PM12/6/05   4:45:23 PM