Panasonic Cd Player Weather Band ReceiverCq 5301u Operating Instructions

							CQ-5301U21
❐Preparation❐Installation Hardware
Warning:If your vehicle is equipped with air bag
and/or anti-theft systems, specific procedures may
be required for connection and disconnection of the
battery to install this product.
Before attempting installation of this electronic
component, contact your vehicle dealer or
manufacturer to determine the required procedure
and strictly follow their instructions. 
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT OF
AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE
AND PERSONAL INJURY.
Caution:Various settings that have been stored in
the memory in other on-board equipment (vehicle
navigation etc.) may be lost if the battery terminals
are disconnected.
Therefore, we recommend to make a record of or to
back up the settings before disconnecting the
terminals.
After completing installation of the main unit, set the
equipment again according to the record. • Disconnect the cable from the negative  battery
terminal (see warning and caution below).
• Remove Mounting Collar 
qfrom the main unit
temporarily, which are already mounted at shipment.*
• Unit should be installed in a horizontal position with
the front end up at a convenient angle, but not more
than 30˚.
❐Dashboard Installation
Installation Opening
This unit can be installed in any dashboard having an
opening as shown below. The dashboard should be
3/16” (4.75 mm) – 7/32” (5.56 mm) thick in order to be
able to support the unit.
Q’tyItemNo.Diagram
q1 Mounting Collar*
Plain washer (5mmø)
w2
Spring Washer (5mmø)e2
Hex. Nut (5mmø)r2
Rear Support Strapt1
Hex. Bolt
(5mmø 
¥25 mm)y1
Toothed Lock Washer
(5mmø)u1
Removal Tool
(U-shaped)i2
Mounting bolt
(5 mmø)
Mounting collarRear support bracket
(provided on the vehicle) Rubber cushion (option)
(a) Using the rear support strap t
(b) Using the rubber cushion (option) 
						

							CQ-5301U22
Installation (Continued)
    
1
2
3
Cautions:
• We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
• When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands
and fingers.
First complete the electrical connections, and then check them for correctness.(apage 24)
The included Mounting Collar qis designed specially for this unit. Do not use it to attach any other model.
Insert Mounting Collar qinto the
dashboard, and bend the mounting tabs
out with a screwdriver.
Establish the rear connection of the unit.
After fixing Power Connector, fix the rear of the unit
to the vehicle body by either method (a) or (b)
shown in the previous page.
After installation reconnect the negative
(–) battery terminal.
The tabs to be bent vary depending on
the vehicle.  To securely install the unit,
fully bend a number of the tabs so that
there is no rattling.
Example:Ta b
qMounting
Collar
Mounting Holes
Mounting Bolt Power Connector
Mounting springs (C)
Engage the Mounting
Springs (C) in the
mounting holes of the
Mounting Collar 
qfirmly.
Mounting SpringMounting
Hole 
						

							CQ-5301U23
To Remove the Unit from the vehicles dashboard
Insert each Removal Tool iand pull.
Note:Do not lose Removal Tools. They will be needed to remove the unit from the vehicles dashboard.
iRemoval Tool
(U-shaped) 
						

							CQ-5301U24
Electrical Connections
Cautions:
• This wiring information is for experienced technical individual, for safety reason, please your dealer wire this
connection.
• This product is designed to operate with a 12 V DC, negative ground battery system.
• To prevent damage to the unit, be sure to follow the connection diagram below.
• Do not insert the power connector into the unit until the wiring is completed.
• Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and
keep cable terminals free from touching any metal parts.
• Remember, if your vehicle has a drive computer or a navigation computer, the data of its memory maybe erased
when the battery terminals are disconnected.
❐Wiring Diagram 
						

							CQ-5301U25
Specifications
❐General
Power Supply: 12 V DC (11 V-16 V) test Voltage 14.4 V, Negative ground
Current consumption: Less than 2.5 A (CD mode, 0.5 W 4-speaker)
Maximum Power Output: 37 W 
¥4 channels at 400 Hz, Volume Control maximum
Tone adjustment range:
Bass: ± 12 dB at 100 Hz
Treble: ± 12 dB at 10 kHz
Power Output: 18 W per channel into 4  ohms, 40 to 30 000 Hz at 3 % THD
Suitable Speaker Impedance: 4-8 Ω
Dimensions (W H D): 7 1-15/16 5-7/8 (178 50 150 mm)
Weight: 2.8 lbs. (1.3k
g)
❐FM Stereo Radio
Frequency Range: 87.9-107.9 MHz
Useable Sensitivity: 12 dBf. (1.1 µV/ 75 Ω, S/N 30 dB)
50 dB Quieting Sensitivity: 17 dBf. (1.8 µV/ 75 Ω)
Frequency Response: 30-15 000 Hz ±3 dB
Alternate Channel Selectivity: 75 dB
Stereo Separation: 35 dB at 1 kHz
Signal/Noise Ratio: 70 dB (Mono)
❐AM Radio
Frequency range: 530 kHz – 1 710 kHz
Usable sensitivity: 28 dB/µV (25 µV, S/N 20 dB)
❐Weather Band Radio
Frequency range: 162.40 – 162.55 MHz
Usable sensitivity: 3 dB/µV (S/N 20 dB)
Signal/Noise Ratio (40 dB/µV): 50 dB
❐CD Player
Sampling Frequency: 32 times oversampling
DA Converter: MASH•1 bit/4 DAC System
Error Correction System: Panasonic Super Decoding Algorithm
Pick-Up Type: 1-beam
Light Source: Semiconductor laser
Wavalength: 790 nm
Frequency Response: 20 - 20,000 Hz (±1 dB)
Signal to Noise Ratio: 85 dB
Total Harmonic Distortion: 0.01 % (1 kHz)
Wow and Flutter: Below measurable limits
Channel Separation: 75 dB
Above specifications comply with EIA standards.
Note:Specifications and the design are subject to modification without notice due to improvements in technology. 
						

							CQ-5301U26
MEMO 
						

							CQ-5301U27
MEMO 
						

							YFM284C478ZA     TAMACO0505-0     Printed in China
Panasonic Consumer Electronics
Company, Division of Panasonic
Electric Corporation of North America
One Panasonic Way, Secaucus,
New Jersey 07094