Panasonic Cd Player Weather Band Receiver Cq 5330u Operating Instructions

							CQ-5330U11
LOUD
MUTE
SCAN MODE
BANDTUNE
SEEK
ILL
PWRALMCLK
CQ-5330U
DISC CD SCAN RPT RDM
APM DISP
VOLSEL / SATPUSH
BASS/TREB/BAL/FADER6 5 4 3 2 16 5 4 3 2 1
Tuning in a Weather Band Station
• Press [BAND]to select WB (Weather Band). (apage 9)
• Press any of the buttons 
[1]to [6]to monitor the preset station.
Weather Band Stations
National Weather Radio Broadcasts from over 380 Iocations throughout the
U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information 24 hours
a day on one of the following frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 165.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Occasionally the frequency of an existing or planned station must be
changed because of unexpected radio frequency interfere with adjacent
NOAA weather Radio Stations and/or with other Government or
commercial Operations within the area. If you have a question concerning
NOAA Weather Radio, please contact your nearest National Weather
Service Office.
Note:The weather band (CH1-6) has been preset. CH7 is selected by
pressing 
[}]or [{].
WB Weather Band Frequency (channel) Number 
						

							CQ-5330U12
CD Player
Disc Insert and Playback
Disc insert
Playback will start automatically after the player recognized
the loaded disc as an ordinary music CD. (When a CD-R or
CD-RW which has CD-DA formatted data as the same as an
ordinary music CD is loaded, this player recognizes it as an
ordinary music CD.)
“LOAd” will be displayed until the disc is loaded.
Notes:
•Do not insert a disc when “DISC” indicator lights.
• The power will be turned on automatically when a disc is
loading.
Stop and Disc Eject
Press [u](eject) to stop CD play and eject the disc.
During disc ejection, “CD EJECT” will be displayed.
Listening to a CD
Press [MODE]to change to the CD player mode.
Playback will start automatically when a disc is loaded.
RadioCD player
LOUD
MUTE
SCAN MODE
BANDTUNE
SEEK
ILL
PWRALMCLK
CQ-5330U
DISC CD SCAN RPT RDM
APM DISP
VOLSEL / SATPUSH
BASS/TREB/BAL/FADER6 5 4 3 2 1
MODE
C
Q
-
5
3
3
0
U
Label Side
u(eject)
( When CD disc loaded ) 
						

							CQ-5330U13
Cautions:
•Only 5 (12 cm) CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit.
• This unit does not support CD text display.
•
This unit does not support MP3 and WMA disc playback.
• Refer to page 23 about notes on CD-Rs/RWs.
• This unit is not designed for any 3 (8 cm) disc.
• If you insert an 3 (8 cm) disc and can not eject it, turn ACC of your car off once and turn it on again, then press
[
u] (eject).
• Do not use irregular shaped discs.
• Do not use discs that have a seal or label attached.
• Do not insert foreign matter into the disc slot.
LOUDMUTE
SCAN MODE
BANDTUNE
SEEK
ILL
PWRALMCLK
CQ-5330U
DISC CD SCAN RPT RDM
APM DISP
VOLSEL / SATPUSH
BASS/TREB/BAL/FADER6 5 4 3 2 1SCANTUNE
SEEK
6 5 4 3 2 1
Track Search
Press and hold...
[2TRACK]: Fast forward
[1TRACK]: Fast reverse
Release to resume the regular play.
Track Selection
Press [2TRACK]: Advance to the next track.
Press 
[1TRACK]: Back to the beginning of the current
track.
Back to the previous track. (Press
twice.)
Repeat play
• Press [5] (RPT).
The current track is repeated.
• Press 
[5] (RPT)again to cancel.
Random play
• Press [6] (RDM).
All the tracks are played in random order.
• Press 
[6] (RDM)again to cancel.
Scan play
• Press [4] (CD SCAN).
The first 10 seconds of each track on the 
disc are played in sequence.
• Press 
[4] (CD SCAN)again to cancel. 
						

							LOUD
MUTE
SCAN MODE
BANDTUNE
SEEK
ILL
PWRALMCLK
CQ-5330U
DISC CD SCAN RPT RDM
APM DISP
VOLSEL / SATPUSH
BASS/TREB/BAL/FADER6 5 4 3 2 1
MODETUNE
SEEK
2 1
CQ-5330U14
CD Changer Control
qCD Changer mode
While a disc magazine is inserted in the CD changer, press [MODE]to select CD changer mode.
Play starts from the first track.
wDisc Selection
[1] ({DISC): Previous disc.
[2] (}DISC): Next disc.
eTrack Selection
Press [TRACK 2]once to go to the next track. Press
repeatedly to step forward through all the tracks.
Press 
[TRACK 1]once to play from the beginning of the
current track, Press twice to play the previous track. Press
repeatedly to step backward through all the tracks.
Track Search
Press and hold [TRACK 2]or [TRACK 1]for more
than 0.5 seconds to activate fast forward or reverse through
a track. Release it to resume the normal CD play from that
position. 
						

							CQ-5330U15
Note:
CD changer functions are applicable to units with optional CD changer unit.
(sold separately)
Scan Play
(Tracks)
• Press [4] (CD SCAN). The track number blinks
and the first 10 seconds of each track on the
discs play in sequence.
• Press 
[4] (CD SCAN)again to cancel and
continue with the current track.
Scan Play
(Discs)
• Press and hold [4] (CD SCAN)for more than 2
seconds. The first track of all the discs in the
magazine is played for 10 seconds each and
Disc Number blinks.
• Press and hold 
[4] (CD SCAN)for more than 2
seconds again to cancel.
Repeat Play
(Tracks)• Press [5] (RPT)to repeat the current track. 
• Press 
[5] (RPT)again to cancel.
blinks
blinks
lights REP: Repeat lndicator
Repeat Play
(Discs)• Press and hold [5] (RPT)for more than 2
seconds to repeat the current disc.
• Press and hold 
[5] (RPT)for more than 2
seconds again to cancel.
blinks REP: Repeat lndicator
Random Play
(Tracks)• Press [6] (RDM)to random selection. Music is
played from all available CDs. 
• Press 
[6] (RDM)again to cancel.
lights R
: Random Indicator
Random Play
(Discs)
• Press and hold [6] (RDM)for more than 2
seconds all the available tracks on the current
disc play in a random sequence.
• Press and hold 
[6] (RDM)for more than 2
seconds again to cancel
blinks R
: Random Indicator
❐Remote Control
CA-RC500U(option) 
						

							CQ-5330U16
Preparation:
Connect the XM receiver (XM DIRECT MODEL:XM-RVR-D-001) to the Unit CQ-5330U.
XM satellite radio is available on a chargable basis.
LOUD
MUTE
SCAN MODE
BANDTUNE
SEEK
ILL
PWRALMCLK
CQ-5330U
DISC CD SCAN RPT RDM
APM DISP
VOLSEL / SATPUSH
BASS/TREB/BAL/FADER6 5 4 3 2 1
qXM Mode
(When a XM receiver is connected.)
Press 
[MODE]to change to the XM mode.
wBand
Press [BAND].
eChannel Selection
Press [}]: Up
Press 
[{]: Down
Press and hold 
[}]or [{]for more than 2
seconds to change channels rapidly.
[CATEGORY]
Category Priority Setting and Selecting
• Push the knob [SEL]for more than 2 seconds.
(Push and hold)
(when category is set ON.) (when category is set OFF.)
(without operation during 5 seconds.)
(interdisplay for 2 seconds.)(blinks)
(without operation during 2 seconds.)
turn right
turn left XM displays as follows, (Example)
Satellite Radio
Indicatorafter 2 seconds
after 5 seconds
XM BandChannel NumberPreset Number
Channel Name
category name
XM Control
rChannel Scan
Press [SCAN], each channel
in ascending order will be
scanned sequentially and
the display will blink for 5
seconds.
Press 
[SCAN]again to stop
scamming and the last
channel will continue to
broadcast. 
						

							CQ-5330U17
• When the display shows “CAT ON”,
Press 
[2] (}): Up
Press 
[1] ({): Down
2 12 1
(without operation during 5 seconds.)
Press [2] or [1].
(Receiving)
(Received)
(interdisplay for 2 seconds.)
Category Name
Category Name
Notes:
CAT OFF: Every channel can be selected from  every category.
CAT ON: Only channels in the current category can be selected.
Default: CAT OFF
Manual Preset Memory
Up to 6 channels each can be saved in the XM1, XM2 and XM3 preset  station memories.
qSelect a band and a channel.
BANDTUNE
SEEK
wPress and hold [1] to [6]for more than 2 seconds to memorize.
Note:
Existing saved channels are overwritten with new channels after the above procedure.• The channel number and the preset number blink once.
6 5 4 3 2 1
Preset memory Calling
qSelect a band.wPress [1]to [6].
BAND6 5 4 3 2 1
Push and hold the knob[SEL] for more than 2 seconds
to resume the normal display.
category on indicator
Note:
When category is on category will be off after pressed any preset button [1]to [6]. 
						

							CQ-5330U18
Display Change
Press and hold [MODE](DISP) for more than 2 seconds.
XM ID Confirmation
• Push and hold the knob [SEL]for more than 2 seconds and then push again during 2 seconds.
MODE
(Press and hold)Channel name
(Reading artist name)
(Reading song title)
Note:
Display when there is no name/title or can not decode.
(Push and hold) (Push)
Note:
If the ID number is 12345678 for example.
• Push the knob for more than 2 seconds to resume to the previous mode when displaying “RADIO ID” or ID number.
• You can also see ID number by selecting CH0.
Error display
XM ID is or communication fails, Press [MODE] to another mode.
Artist name
song title
XM Control (Continued)
(Reading categry)
Category name 
						

							CQ-5330U19
Troubleshooting 
Preliminary Steps
Check and take steps as described in the tables below.
If You Suspect Something Wrong
Immediately switch the power off.
Disconnect the power connector and check that there is
neither smoke nor heat from the unit before asking for
repairs. Never try to repair the unit by yourself because it
is dangerous to do so.
No power.
Trouble
Vehicle’s ignition switch is not on.
aTurn your vehicle’s ignition switch to ACC or ON.
Cables are not correctly connected.
aConnect cables correctly.
Powere connector is not correctly connected.
aConnect the power connector to the terminal that is always active.
Power connector is not correctly connected. 
aConnect the power connector to your vehicle’s ACC source.
Grounding wire is not correctly connected. 
aConnect the grounding wire to a metal part of the venicle.
Mute is set to ON. 
aSet it to OFF.
Cables are not correctly connected. 
aConnect cables correctly.
The ground lead is not connected properly. 
aConnect the ground lead properly.
Cautions:
• Do not use the unit if it malfunctions or if there is
something wrong.
• Do not use the unit in irregular condition, for
example, without sound, or with smoke or foul
smell, which can cause ignition or electric shock.
Immediately stop using it and call the store where
you purchased it.
Cause/Step
Troubleshooting Tips
❐Common
No sound.
Noise. 
						

							CQ-5330U20
Troubleshooting (Continued)
Much noise in FM stereo
and monaural broad-
casts.
Trouble
Station is too far, or signals are too weak.
aSelect other stations of higher signal level.
The radio antenna is not extended enough.
aExtend fully the radio antenna.
Preset station is reset.Battery cable is not correctly connected.
aConnect the battery cable to the terminal that is always active.
Cause/Step
❐Radio
Disc is in the CD
compartment but no
sound is made, or disc is
ejected automatically.
Trouble
Disc is upside down.
aPlace disc in the correct direction with the label side up.
Sound skips, bad sound
quality. (e.g. caused by
noise)
• Disc is dirty.
• Disc has scratches.
aClean disc, referring to the section on “Notes on Discs”.
aThe unit may not successfully playback a CD-R/RW that is made in
combination of writing software, a CD recorder (CD-R/RW drive) and a
disc which are incompatible one another. Refer to instructions for the
concerned devices for details.
• Disc is dirty.
• Disc has scratches.
aClean disc, referring to the section on “Notes on Discs”.
A disc that has data other than CD-DA type is loaded.
aDiscs that have CD-DA type data should be used.
aThe unit may not successfully playback a CD-R/RW that is made in
combination of writing software, a CD recorder (CD-R/RW drive) and a
disc which are incompatible one another. Refer to instructions for the
concerned devices for details.
Cause/Step
❐CD