Panasonic Bluray Disc Home Theater Sound System Sc Btt490 Owners Manual

							Advanced 
operations 
41VQT3X49
∫ Delay time
For optimum listening with 5.1-channel sound, all 
the speakers, except for the subwoofer, should be 
the same distance from the seating position.
If either distance 1  or 2  is less than  3, 
measure the distance and adjust the time to make 
up for the difference (see the table below).
1  2  3 : Primary listening distance
A Actual speaker position
B Ideal speaker position
1 Press [ 3,4 ,2, 1] to select the distance 
box ( ) and press [OK].
2 Press [ 3,4 ] to select the setting and 
press [OK].
Delay time for the Center speaker Subtract the distance  1 from  3
Delay time for the Surround and Surround 
back speakers Subtract the distance  2 from  3
To finish the speaker settingPress [ 3,4 ,2, 1] to select “Complete” and 
press [OK].
Enjoying sound effects 
from all speakers
For more details on each setting, refer to “Audio 
Settings” on the Option menu (>34)
1 Press [SURROUND].
2 Press [ 3,4] to select “MULTI CH SOURCE” 
or “2CH SOURCE”, and then press [OK].
e.g.,
3While the selected mode is displayed
Press [3,4] to select the desired setting. (>34)
∫ Adjusting speaker level during 
play
1 Press [CH SELECT] to activate the speaker 
setting mode.
2 Press [CH SELECT] several times to select 
the speaker.
≥Press [ 2,1] to adjust the balance of 
the front speakers.
3Press [3] (increase) or [4] (decrease) to adjust 
the speaker level for each speaker. 
s 6 dB to  r6 dB
1 Press [SOUND].
2Press [3,4] to select “2CH SOURCE” or 
“ ALL SOURCE”, and then press [OK].
e.g.,
3 While the selected mode is displayed
Press [ 3,4] to select the desired setting and 
press [OK]. 
Repeat this procedure if necessary. ( >34)
	≥The sound effects/modes may not be available or have no 
effect with some sources.
≥ You may experience a reduction in sound quality when 
these sound effects/modes are used with some sources. If 
this occurs, turn the sound effects/modes off.
Distance  (Approx.)Setting
34 cm (1 ft. 1 in.)1.0 ms
68 cm (2 ft. 2 in.)2.0 ms
102 cm (3 ft. 4 in.)3.0 ms
136 cm (4 ft. 5 in.)4.0 ms
170 cm (5 ft. 6 in.)5.0 ms
Distance  (Approx.)Setting
170 cm (5 ft. 6 in.)5.0 ms
340cm (11ft. 1in.)10.0 ms
510 cm (16 ft. 8 in.)15.0 ms
: 
: 
L
LS
R
SW
C
RS
C
RSLS
1
2
3 A
B
0.0ms
Surround Effects
Sound Effects
SC-BTT490P_eng.book  41 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							42VQT3X49
Speaker installation 
option
Consult a qualified building contractor when 
attaching the speakers to a wall. Improper 
attachment may result in damage to the wall and 
speakers and personal injury.
You can attach all of the speakers (except 
subwoofer) to a wall.
≥The wall or pillar on which the speakers are to 
be attached should be capable of supporting 
10 k g (22 lbs) per screw.
1Drive a screw (not supplied) into the wall.
AAt least 30 mm (1 3/16q)
B‰ 4.0 mm (5/32q)
C ‰ 7.0 mm to ‰ 9.4 mm (9/32q to 3/8q)
D Wall or pillar
E 5.5mm to 7.5mm (
7/32q to 5/16q)
2Fit the speaker securely onto the screw(s) 
with the hole(s).
Use the measurements indicated below to identify 
the screwing positions on the wall.
≥ Leave at least 20 mm (
25/32q) of space above the 
speaker and 10 mm (13/32q) on each side to 
allow enough space for fitting the speaker. Front speaker
Attach to a wall without the base and the stand.
A
51 mm (2 q)
B 64 mm (2 
17/30q)
C 350 mm (13 25/32q)
Surround speaker
D 40 mm (1 
9/16q)
E 24 mm (15/16q)
Center speaker
F 18 mm (
23/32q)
G 25 mm (31/32q)
H 230.5 mm (9 1/16q)
Attaching to a wall
e.g., Front speaker
DO NOTDO
≥In this position, the 
speaker will likely 
fall if moved to the 
left or right.≥Move the speaker 
so that the screw is 
in this position.

 








\b

SC-BTT490P_eng.book  42 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							Advanced 
operations 
43VQT3X49
It is possible to shorten the height of the front 
speaker by directly connec ting the speaker to the 
base without using the stand.
Preparation
Detach the speaker cable from the stand.
1Thread the detached cable through the 
base.
2Attach the speaker to the base and tighten 
the screw (supplied) securely.
3Connect the speaker cable to the speaker 
and to the terminal of the main unit. 
(> 12, 13)
∫ Reattaching the speaker cable 
to the stand
Preventing from falling
Front speaker
Preventing from dropping
Front speaker, Surround speaker, Center speaker
1Thread a string to the speaker.
≥Use a string of less than  ‰ 2.0 mm (3/32q), 
which is capable of supporting over 10 k g 
(22 lbs).
e.g., Front speaker
A String (not supplied)
B Rear of the speaker
2Thread a string from the wall to the 
speaker and tie tightly.
C Screw eye (not supplied)
D Wall
E Approx.150 mm (5 
29/32q)
F Less than 100 mm (3 15/16q)
Front speaker assembly option
Straighten the 
cable and run 
through the 
stand. Pull out the 
cable through 
the hole.
Preventing the speakers 
from falling or dropping







When mounted on a wall When placed on the floor
SC-BTT490P_eng.book  43 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							44VQT3X49
ReferenceTroubleshooting guide
Before requesting service, please perform the 
following steps.
The following do not indicate a problem with this unit:– Regular disc rotating sounds.
– Image disturbance during search.
– Image disturbance when replacing 3D discs.
∫Unit doesn’t respond to remote 
control or front panel buttons.
Press and hold [Í/I] on the main unit for 3 seconds.– If still unable to power the unit off, disconnect the power 
cord, wait 1 minute, then reconnect the power cord.
∫ Cannot eject disc.
The unit may have a problem.
1 While the unit is off, press and hold [OK], [B] 
and [Y] on the remote control at the same 
time for more than 5 seconds.
–“00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote 
control or [ Í/I] on the unit until “06 FTO” is 
displayed on the unit’s display.
3 Press [OK] on the remote control or 
[< OPEN/CLOSE] on the unit. To return to the factory preset.
¾
Select “Yes” in “Restore Default Settings” in 
the Setup menu. ( >40)
To return all settings to the factory preset.
¾ Reset the unit as follows:
1 While the unit is off, press and hold [OK], [B] 
and [Y] on the remote control at the same 
time for more than 5 seconds.
–“00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote 
control or [ Í/I] on the unit until “08 FIN” is 
displayed on the unit’s display.
3Press and hold [OK] on the remote control or 
[8)¾The remote control and main unit are using different 
codes. If “SET 
” is displayed on the unit’s display 
when a button is pressed on the remote control, 
change the code on the remote control. 
(>40, 48)
The TV tuner mode is not displayed when the 
TV is switched on.
¾
This phenomenon may occur, depending on the 
TV setting, when “Quick Start” is set to “On”.
¾ Depending on the TV, this phenomenon may 
be prevented by reconnecting the HDMI cable 
to a different HDMI input terminal or by 
changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾The ratings level returns to the factory preset.
1 While the unit is on, press and hold [OK], [B] 
and [Y] on the remote control at the same 
time for more than 5 seconds.
–“00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote 
control or [ Í/I] on the unit until “03 VL” is 
displayed on the unit’s display.
3 Press [OK] on the remote control or 
[< OPEN/CLOSE] on the unit.
(For the U.S.A. and Canada)
Do you have the latest firmware installed?
Firmware updates may be released to correct 
operating irregularities that are discovered 
with certain movies. ( >19)
4
Make the following checks and visit our 
website for more information.
For U.S.A. : 
www.panasonic.com/help
Enter the model number.
For Canada : 
http://www.panasonic.ca 4
Or visit our website to find a service center.You can find a service c enter near you easily 
on our website.
Other support information :
“Customer Services Directory (United States 
and Puerto Rico)” ( >54) or “Limited 
Warranty (Only for CANADA)” ( >55).
(For units with PX printed on the packaging)
Do you have the latest firmware installed?
Firmware updates may be released to correct 
operating irregularities that are discovered 
with certain movies. ( >19)
Even so, you still have trouble, consult your dealer.
General operation
SC-BTT490P_eng.book  44 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							Reference
45VQT3X49
This unit does not recognize the USB 
connection correctly.
¾Disconnect and reconnect the USB cable. If it 
still does not recognize the connection, turn 
the power of this unit off and on again.
¾ If you connect USB HDD to this unit, use USB 
extension cable that is supplied with the HDD.
The unit switches to standby mode.
¾This unit will automatically turn to standby 
mode after 30 minutes if it is inactive. ( >21)
¾ When the time set for the sleep timer has 
passed, the power will be turned off. ( >8)
¾
One of the unit’s safety devices is activated. Press 
[
Í/I] on the main unit to turn the unit on.
The unit does not turn off.
1 Press and hold [ Í/I] on the main unit for 5 
seconds. (If still unable to power the unit off, 
disconnect the power cord, wait 1 minute, 
then reconnect the power cord.)
2Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME], 
[
40)
¾ When “3D BD-Video Playback” in the Setup 
menu is set to “Auto”, images may not be 
output depending on the connection method. 
After removing the disc from this unit, select 
“Set before play” in the Setup menu, and 
select “2D Playback” in the setup screen 
displayed when playing 3D discs. ( >37) ¾
If irregular coloring occurs on your TV, turn 
the TV off for about 30 minutes.
If it persists, move the speakers further away from the TV.
Video is not output.
¾
Set “High Clarity Sound” in the Setup menu to 
“Disable” to use the VIDEO OUT terminal. (>37)
Video is not output in high-definition.
¾Confirm that “HDMI Resolution” in the Setup 
menu is set properly. ( >36)
3D video is not output.
¾ Change the settings as required by the 
connected TV format. ( >37, “3D Type”)
¾
Are the settings on this unit and the TV correct? (>24)¾Depending on the connected TV, the video being 
played back might switch to 2D video due to changes 
in resolution etc. Check the 3D setting on the TV.
¾ Check that proper HDMI video input is 
selected on the TV.
3D video is not output correctly as 2D.
¾Select “Set before play” in the Setup menu, 
and select “2D Playback” in the setup screen 
displayed when playing 3D discs. ( >37, “3D 
BD-Video Playback”)
¾ Discs that have recorded titles with Side by 
side (2 screen structure) and that can be 
enjoyed in 3D are played back in accordance 
with the settings of the TV.
No subtitles.
¾When progressive output is on, closed 
captions/subtitles cannot be displayed.
The subtitles overlap closed captions 
recorded on discs.
¾Turn off the subtitles or the closed caption 
setting on the TV.  (> 32)
A black band is displayed around the edge of 
the screen.
The aspect ratio of the screen is abnormal.
¾
Confirm the “TV Aspect” is set properly. (>39)
¾ Adjust the aspect setting on the television.
Picture
SC-BTT490P_eng.book  45 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							46VQT3X49
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
¾Check connections to speakers and other 
equipment. ( >11s17)
¾ Ensure the speaker settings for your 
speakers are correct. ( >40)
¾ To output audio from a device connected with 
an HDMI cable, set “HDMI Audio Output” to 
“On” in the Setup menu. ( >37)
¾
When “BD-Video Secondary Audio” is set to “On”, 
Dolby TrueHD, Dolby Digital Plus, DTS-HD Master 
Audio and DTS-HD High Resolution Audio are 
output as Dolby Digital or DTS Digital Surround.
¾Re-master will not work when the bitstream signal 
is output from the HDMI AV OUT terminal. (>34)¾ Depending on the connected equipment, the 
sound may be distorted if this unit is 
connected with an HDMI cable.
¾ The multi-channel audio from a device 
connected to the TV is not output in it’s 
original multi-channel form.
–If the device has an optical audio output 
terminal, connect the device to this unit’s 
DIGITAL AUDIO IN terminal. ( >16)
No surround sound.
¾Press [SURROUND] to select a surround effect. (>41)
¾ (When using the 7.1ch speaker system)Audio is not available from the surround back speakers 
(optional) even though Dolby Pro Logic II turns on.
Cannot switch audio.
¾When audio is output from the HDMI AV OUT 
terminal, set “Dolby D/Dolby D +/Dolby 
TrueHD” or “DTS/DTS-HD” to “PCM”. ( >36)
No sound from the TV.
¾ Press [EXT-IN] to select the corresponding 
source. ( >20)
¾ When connecting the unit to a TV using an 
HDMI cable, check whether the HDMI 
terminal on the TV is labeled “HDMI (ARC)”. If 
not labeled in this way, connect using the 
HDMI cable in combination with an optical 
digital audio cable.( >14)
¾ If there is no sound from the equipment 
connected to this unit’s DIGITAL AUDIO IN 
terminal, please make sure that the optical 
audio output of the equipment is set to PCM. Disc cannot be played.
¾
The disc is dirty. (> 5)
Still pictures (JPEG) do not play back normally.
¾The images that were edited on the PC, such as 
Progressive JPEG, etc., may not be played back.
I can’t play back BD-Live.
¾The SD card is write-protected. ( >7)
¾ Confirm that this unit is connected to the 
broadband Internet. ( >17)
¾ Confirm the “BD-Live Internet Access” 
settings. ( >39)
¾ Confirm an SD card is inserted into the SD 
card slot. ( >20)
Alternative soundtrack and subtitles cannot 
be selected.
¾ The languages are not recorded on the disc.
¾
You may not be able to use the Option menu to 
change the soundtrack and subtitles on some discs. 
Use the disc’s menus to make changes. (
>24)
Cannot charge or operate.
¾Check that the iPod/iPhone is connected firmly. (>26)
¾The battery of the iPod/iPhone is depleted. Charge 
the iPod/iPhone, and then operate again.
¾When unexpected operation occurs while using the 
iPod/iPhone, connect the iPod/iPhone again or try 
to restart the iPod/iPhone.
Cannot display iPod/iPhone videos/photos on the TV.¾ Make sure that TV is connected to the VIDEO 
OUT terminal on this unit. ( >15)
¾
Operate the iPod/iPhone menu to make the 
appropriate video/photo output settings for your TV. 
(Refer to operating instructions for your iPod/iPhone.)
The TV input channel unintentionally changes 
to HDMI input.
¾
When the main unit is connected with an “HDAVI 
Control” compatible TV and VIDEO IN is selected for 
iPod/iPhone video or photo playback, the TV input 
channel will automatically change to the HDMI input 
channel when [HOME] is pressed.
–Re-select the TV’s VIDEO IN input channel.
SoundPlayback
iPod/iPhone operation
SC-BTT490P_eng.book  46 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							Reference
47VQT3X49
Distorted sound or noise is heard.
¾Adjust the position of the antenna.
A beat sound is heard.
¾Try to keep a certain amount of distance 
between the antenna and the TV.
Stations cannot be selected.
1Press [RADIO] to select “FM”.
2 Press and hold [RADIO].
After a few seconds the display changes to show 
the current lowest frequency (87.9 MHz). Continue 
to hold the button down. The lowest frequency 
changes (87.5 MHz) and the step is changed.
Noise is excessive.
¾Change the audio to be output as monaural.
1 Press and hold [ jAUDIO].
2 Press [ jAUDIO] to select “MONO”.
The sound becomes monaural.
≥ To cancel, press the button again or change 
the frequency.
In normal circumstances, select “AUTO STEREO”
I can’t connect to the network.
¾ Confirm the network connection and settings. 
(>17, 18, 38)
¾ Check the operating instructions for each 
device and connect accordingly.
When using wireless LAN connection, video from 
the DLNA Certified media server is not played back 
or video frames are dropped during playback.
¾Higher transfer rate router such as 802.11n 
(2.4 GHz) wireless router may solve the 
problem. If you use 802.11n (2.4 GHz) 
wireless router, it is necessary to set the 
encryption type to “AES”.
Simultaneous use with a microwave, cordless 
telephone etc. at 2.4 GHz may result in 
connection interruptions or other problems.
¾
On the “Wireless Settings” screen (>38), the 
continuous lighting of at least 4 “Reception” 
indicators is the target for a stable connection. If 3 
or fewer indicators are lit or the connection is being 
interrupted, change the position or angle of your 
wireless router and see if the connection state 
improves. If there is no improvement, connect to a 
wired network and perform the “Easy Network 
Setting” (
>18) again.
Messages
The following messages or service numbers 
appear on the television or unit’s display.
Cannot play.
¾ You inserted an incompatible disc (Discs 
recorded in PAL video, etc.).
Cannot display on this unit.
¾You tried to play a non-compatible image.
¾ Confirm “SD” on the unit’s display is not 
displayed and re-insert the card.
No disc inserted.
¾The disc may be upside down.
$ This operation is not available.
¾ Some operations are unsupported by the unit. 
For example;
–BD-Video: During playback, reverse  slow-motion or reverse frame-by-frame is 
not possible.
IP address is not set.
¾ The “IP Address” in “IP Address/DNS 
Settings” is “---. ---. ---. ---”. Set the “IP 
Address”, “Subnet Mask”, and “Default 
Gateway”. (Select the automatic address 
acquisition if necessary.)
The current wireless network security setting 
is weak. It is recommended to change to a 
stronger security setting.
¾
Authentication type for the wireless LAN is set to 
“Open system”, or the encryption type is set to 
“No encryption”. It is recommended to encrypt for 
safety reasons. For details, refer to the 
instructions of the wireless router being used. 
Encryption is required when playing back video, 
etc., from DLNA compatible devices.
No Video
¾Depending on the connected iPod/iPhone, 
video menu may not be available on the TV. 
Select “ALL” on the unit’s display and operate 
video playback from y our iPod/iPhone menu. 
(> 26)
Radio
Network
On the television
SC-BTT490P_eng.book  47 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							48VQT3X49
F99
¾The unit fails to operate properly. Press [ Í/I] 
on the main unit for 3 seconds to switch the 
unit to standby, then switch back on.
HDMI ONLY
¾ Some BD-Video discs can only be output with 
HDMI.
NET
¾While connecting to a network.
No PLAY
¾There is a viewing restriction on a BD-Video 
or DVD-Video. ( >39)
No READ
¾ The media is dirty or badly scratched. The 
unit cannot play.
PLEASE WAIT
¾The unit is carrying out an internal process. 
This is not a malfunction. You cannot operate 
the unit while “PLEASE WAIT” is displayed.
REMOVE
¾The USB device is drawing too much power. 
Remove the USB device.
SET   (“    ” stands for a number.)
¾ The remote control and main unit are using 
different codes. Change the code on the 
remote control.
Press and hold [OK] and 
the indicated number 
button at the same time for 
more than 5 seconds.
U59
¾The unit is hot.
The unit switches to standby for safety 
reasons. Wait for about 30 minutes until the 
message disappears.
Select a position with good ventilation when 
installing the unit.
H or F
(“  ” stands for a number.)
¾ Check and correct the speaker cable 
connections.
¾ There is something unusual. ¾
Check the unit using the troubleshooting 
guide. If the service number remains 
displayed, do the following.
1 Disconnect the plug from the AC outlet, wait a 
few seconds, then reconnect it.
2 Press [ Í/I] to turn the power on.
If the service number remains displayed despite 
doing the above, request service from the dealer. 
Inform the dealer of the service number when 
requesting service.
IPOD OVER CURRENT ERROR
¾ The iPod/iPhone is drawing too much power. 
Remove the iPod/iPhone, and turn the unit off 
and on again.
START
¾The system is being restarted during the 
firmware update. Please do not turn off the 
unit.
UPD /
(“  ” stands for a number.)
¾ The firmware is being updated.
Please do not turn off the unit.
FINISH
¾The firmware update is complete.
NOT CONDITIONAL
¾The requested operation cannot be 
conducted.
SET OK
¾The stations are set, and the radio tunes to 
the last preset station.
ERROR
¾Automatic presetting is unsuccessful. Preset 
the stations manually.
TUNED/STEREO
¾Stereo broadcasting or stereo sound is 
selected.
TUNED
¾Monaural broadcasting or monaural sound is 
selected.
On the unit’s display
SC-BTT490P_eng.book  48 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							Reference
49VQT3X49
Specifications
* The impedance of all the speakers is 3≠.
* This unit supports “HDAVI Control 5” function.
Specifications are subject to change without notice.
GENERAL
Power consumption
(For the U.S.A. and Canada):84 W
(For units with PX printed 
on the packaging): 89 W
Power consumption in standby mode
(For the U.S.A. and Canada):Approx. 0.05 W
(For units with PX printed 
on the packaging): Approx. 0.1 W
Power supply
(For the U.S.A. and Canada):AC 120 V, 60 Hz
(For units with PX printed 
on the packaging): AC 110 V to 127 V, 
220 V to 240 V, 
50 Hz/60 Hz
iPod/iPhone Connector: DC OUT 5V 1.0A MAX
Dimensions (W kHk D):
430 mmk38 mmk279 mm(1615/16qk 11/2qk1031/32q)
Mass (Weight): Approx. 2.7 kg (6 lbs)
Operating temperature range:0oC to 40oC(32oF to 104oF)Operating humidity range:35 % to 80 % RH (no condensation)
AMPLIFIER SECTION
RMS TOTAL POWER OUTPUT: 1000 W
1 kHz, 10 % total harmonic distortion
FRONT: 185 W per ch (3
≠)CENTER: 180 W per ch (3
≠)
SURROUND: 125 W per ch (3
≠)
100 Hz, 10 % total harmonic distortion
SUBWOOFER:200 W per ch (3 ≠)
FTC TOTAL POWER OUTPUT:  430 W
120 Hz to 20 kHz, 1.0 % total harmonic distortion
FRONT:60 W per ch (3 ≠)
CENTER: 90 W per ch (3 ≠)
SURROUND:60 W per ch (3 ≠)
45 Hz to 120 Hz, 1.0 % total harmonic distortion
SUBWOOFER: 100 W (3≠)
Audio Input AUX: k1
Digital Audio Input Optical k1
HDMI AV input k2
Sampling frequency:
32 kHz, 44.1 kHz, 48 kHzAudio Format:PCM, Dolby Digital, DTS
FM TUNER SECTION
Frequency range:87.9 MHz to 107.9 MHz (200 kHz step), 
87.5 MHz to 108.0 MHz (100 kHz step)
Antenna terminals:75 ≠ (unbalanced)
SPEAKER SECTION*
FRONT SPEAKERS
Full range: 6.5 cm (21/2q) CONE TYPE
Dimensions (W kHk D):292 mmk1185 mmk292 mm(111/2qk 4621/32qk111/2q)
Mass (Weight): Approx. 2.6 kg (5.7 lbs)
CENTER SPEAKER Woofer: 6.5 cm (2
1/2q) CONE TYPE
Full range: 6.5 cm (21/2q) CONE TYPE
Dimensions (W kHk D): 280 mmk 84 mmk78 mm
(11
1/32qk 35/16qk33/32q)
Mass (Weight): Approx. 0.91 kg (2.0 lbs)
SURROUND SPEAKERS Full range: 6.5 cm (2
1/2q) CONE TYPE
Dimensions (W kHk D): 80 mm k139 mm k70 mm
(3
5/32qk 51/2qk225/32q)
Mass (Weight): Approx. 0.47 kg (1.0 lbs)
SUBWOOFER Woofer: 16 cm (6
1/2q) CONE TYPE
Dimensions (W kHk D):180 mmk408 mmk300 mm(73/32qk 161/16qk1113/16q)
Mass (Weight): Approx. 4.3 kg (9.5 lbs)
TERMINAL SECTION
USB slot: USB2.0: 2 system
SD card slot: Connector: 1 system
Ethernet: 10BASE-T/100BASE-TX 1 system
Wireless LAN: Standard Compliance:  IEEE802.11 b/g/n
Frequency range: 2.4 GHz band
Security: 
WPA
TM/WPA2TM 
(Encryption Type: TKIP/AES, Authentication Type: PSK), WEP (64 bit/128 bit)
VIDEO SECTION
Signal system: NTSC
Video output Output level: 1.0 Vp-p (75≠)
Output connector:Pin jack (1 system)
HDMI AV output* Output 
connector: Type A (19 pin)
HDMI AV Input*
Input connector:Type A (19 pin) 2 system
LASER Specification Class  I LASER Product
Wave length:
790 nm (CDs)/660 nm (DVDs)/405 nm (BDs)Laser power: No hazardous radiation is emitted 
with the safety protection
SC-BTT490P_eng.book  49 ページ  ２０１２年２月２２日　水曜日　午前９時１分 
						

							50VQT3X49
≥With certain recording states and folder structures, the 
play order may differ or playback may not be possible.
Supplemental 
infor mation
∫ Display languages list
∫ Language code list
File format
File formatExtensionReference
MP3 “.MP3”, “.mp3”
This unit supports ID3 tags, 
but only titles, artist names 
and album names can be 
displayed.
JPEG “.JPG”, “.jpg”
≥MOTION JPEG and 
Progressive JPEG is not 
supported
≥ You may not be able to 
play back the file if you 
have edited the folder 
structure or the file name 
on a PC or other device.
MKV “.MKV”, “.mkv”
≥
The video file and 
subtitles text file are 
inside the same folder, 
and the file names are 
the same except for the 
file extensions.
≥ Some MKV files may not 
play back, depending on 
the video resolution and 
frame rate condition.
Subtitles text 
file
“.SRT”, “.srt”, 
“.SSA”, “.ssa”, 
“.ASS”, “.ass”
FLAC “.flac”Maximum sampling rate:
192 kHz/24 bit
WAV“.wav”Maximum sampling rate:
48 kHz/16 bit
MPO “.mpo”3D still picture
Restriction on use of 
unauthorized copied content
This unit adopts the following technology for 
copyright protection.
Cinavia Notice
This product uses Cinavia technology to limit 
the use of unauthorized copies of some 
commercially-produced film and videos and 
their soundtracks. When a prohibited use of an 
unauthorized copy is detected, a message will 
be displayed and playback or copying will be 
interrupted.
More information about Cinavia technology is 
provided at the Cinavia Online Consumer 
Information Center at http://www.cinavia.com
. 
To request additional information about Cinavia 
by mail, send a postcard with your mailing 
address to:
Cinavia Consumer Information Center, P.O. 
Box 86851, San Diego, CA, 92138, USA. 
DisplayLanguageDisplayLanguageDisplayLanguage
LanguageCodeLanguageCodeLanguageCode
ENG
FRA
DEU
ITA
ESP
NLD
SVE
NOR
DAN
POR
RUS English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian ARA  
HIN
PER
IND
MRI
BUL
RUM
GRE
TUR 
JPN
CHI
KOR
MAL
VIE
THA
POL
CES
SLK
HUN
FIN Japanese
Chinese
Korean
Malay
Vietnamese
Thai
Polish
Czech
Slovak
Hungarian
FinnishArabic
Hindi
Persian
Indonesian
Maori
Bulgarian
Romanian
Greek
Turkish
Others
Abkhazian: 6566
Afar: 6565
Afrikaans: 6570
Albanian: 8381
Amharic
:6577
Arabic: 6582
Armenian: 7289
Assamese: 6583
Aymara: 6589
Azerbaijani: 6590
Bashkir: 6665
Basque: 6985
Bengali; Bangla: 6678
Bhutani: 6890
Bihari: 6672
Breton: 6682
Bulgarian: 6671
Burmese: 7789
Byelorussian: 6669
Cambodian: 7577
Catalan: 6765
Chinese: 9072
Corsican: 6779
Croatian: 7282
Czech: 6783
Danish: 6865
Dutch: 7876
English: 6978
Esperanto: 6979
Estonian: 6984
Faroese: 7079
Fiji: 7074
Finnish: 7073
French: 7082
Frisian: 7089
Galician: 7176
Georgian: 7565
German: 6869
Greek: 6976
Greenlandic: 7576
Guarani: 7178 Gujarati: 7185
Hausa: 7265
Hebrew: 7387
Hindi: 7273
Hungarian: 7285
Icelandic: 7383
Indonesian: 7378
Interlingua: 7365
Irish:
7165
Italian: 7384
Japanese: 7465
Javanese: 7487
Kannada: 7578
Kashmiri: 7583
Kazakh: 7575
Kirghiz: 7589
Korean: 7579
Kurdish: 7585
Laotian: 7679
Latin: 7665
Latvian, Lettish: 7686
Lingala: 7678
Lithuanian: 7684
Macedonian: 7775
Malagasy: 7771
Malay: 7783
Malayalam: 7776
Maltese: 7784
Maori: 7773
Marathi: 7782
Moldavian: 7779
Mongolian: 7778
Nauru: 7865
Nepali: 7869
Norwegian: 7879
Oriya: 7982
Pashto, Pushto: 8083
Persian: 7065
Polish: 8076
Portuguese: 8084
Punjabi: 8065
Quechua: 8185 Rhaeto-Romance:
8277
Romanian: 8279
Russian: 8285
Samoan: 8377
Sanskrit: 8365
Scots Gaelic: 7168
Serbian: 8382
Serbo-Croatian: 8372
Shona: 8378
Sindhi: 8368
Singhalese: 8373
Slovak: 8375
Slovenian: 8376
Somali: 8379
Spanish: 6983
Sundanese: 8385
Swahili: 8387
Swedish: 8386
Tagalog: 8476
Tajik: 8471
Tamil: 8465
Tatar: 8484
Telugu: 8469
Thai: 8472
Tibetan: 6679
Tigrinya: 8473
Tonga: 8479
Turkish: 8482
Turkmen: 8475
Twi: 8487
Ukrainian: 8575
Urdu: 8582
Uzbek: 8590
Vietnamese: 8673
Volapük: 8679
Welsh: 6789
Wolof: 8779
Xhosa: 8872
Yiddish: 7473
Yo r u b a : 8 9 7 9
Zulu: 9085
SC-BTT490P_eng.book  50 ページ  ２０１２年２月２２日　水曜日　午前９時１分