Home
>
Panasonic
>
Home Theater System
>
Panasonic Bluray Disc Home Theater Sound System Sc Btt268 Owners Manual
Panasonic Bluray Disc Home Theater Sound System Sc Btt268 Owners Manual
Have a look at the manual Panasonic Bluray Disc Home Theater Sound System Sc Btt268 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Advanced operations 31 VQT3M40 Movie Sound Effect Select the sound effect of the movie. ≥Cinema Surround Plus: The function creates the sound of virtual speakers to enhance the realistic surround feeling as if the sound comes from all directions. Music Sound Effects*1, *2 Select the sound effect of the music. ≥Digital Tube Sound: This feature gives you warm sound, like that produced by a vacuum tube amplifier. ≥ Re-master: This feature gives you bright er sound by increasing the high frequency portion of the audio. (Discs recorded at 48 kHz or less) Recommended settings: High Clarity Sound When connected to TV via the HDMI AV OUT terminal for outputting image, it produces clearer sound. ≥ Only when you have selected “Enable” in “High Clarity Sound” ( >32). Setup menu Change the unit’s settings if necessary. The settings remain intact even if you switch the unit to standby. 1Press [HOME]. 2Press [ 3,4,2, 1] to select “Others” and press [OK]. 3Press [OK] to select “Setup”. 4Press [ 3,4] to select the menu and press [OK]. 5Press [ 3,4] to select the item and press [OK]. If there are any other it ems, repeat these steps. 6Press [3,4,2, 1] to select the option and press [OK]. ≥ There may be differences in operation methods. If this happens, follow the on-screen instructions for the operation. DVD-Video Ratings Set a ratings level to limit DVD-Video play. ≥Follow the on-screen instructions. Enter the 4-digit password with the number buttons when the password screen is shown. BD-Video Ratings Set an age limit of BD-Video play. ≥Follow the on-screen instructions. Enter the 4-digit password with the number buttons when the password screen is shown. 3D BD-Video Playback Select the playback method of 3D compatible video software. Audio Language Choose the language for audio. ≥If “Original” is selected, the original language of each disc will be selected. ≥ Enter a code ( >40) with the number buttons when you select “Other ¢¢¢¢”. Audio Re-master 1 Pop and rock Re-master 2Jazz Re-master 3Classical *1 When audio is output from the HDMI AV OUT terminal this function is effective only when “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/ DTS-HD” is set to “PCM”. ( >32) *2 This function has no effect when the type of audio is Dolby Pro Logic II.About the password The following items use the same password. Don’t forget your password. ≥ “DVD-Video Ratings” ≥ “BD-Video Ratings” ≥ “Lock” ( >34) Disc RETURN SetupDiscVideoAudioDisplayTV / Device ConnectionNetworkOthers OK VQT3M40~Body_mst.fm 31 ページ 2010年12月24日 金曜日 午後7時59分
32 VQT3M40 Subtitle Language Choose the language for the subtitle. ≥If “Automatic” is selected and the language selected for “Audio Language” is not available, subtitles of that language will automatically appear if available on that disc. ≥ Enter a code ( >40) with the number buttons when you select “Other ¢¢¢¢”. Menu Language Choose the language for the disc menus. ≥Enter a code ( >40) with the number buttons when you select “Other ¢¢¢¢”. BD-Live Internet Access ( >21) You can restrict Internet access when BD-Live functions are used.≥If “Allow ( Limited )” is selected, Internet access is permitted only for BD-Live contents which have content owner certificates. Still Mode (paused video) Select the type of picture shown when you pause playback. Seamless Play The chapter segments in playlists are played seamlessly. ≥Select “On”, when the picture freezes for a moment at the chapters segment in playlists. Black Level Control Select lighter or darker for adjusting the black level control to the desired setting for picture enhancement. Dynamic Range Compression You can listen at low volumes but still hear dialog clearly. (Dolby Digital, Dolby Digital Plus and Dolby TrueHD only) ≥“Auto” is effective only when playing Dolby TrueHD. Digital Audio Output Press [OK] to show the following settings: Dolby D/Dolby D +/Dolby TrueHD DTS/DTS-HD Select the audio signal to output .≥Select “PCM”, when the connected equipment cannot decode the respective audio format. ≥ Not making the proper settings may result in noise. BD-Video Secondary Audio Select whether to mix or not mix the primary audio and secondary audio (including the button click sound). ( >21) ≥ If “Off” is selected, the unit outputs the primary audio only. Digital Audio Input Press [OK] to show the following settings: PCM-FIX Select the following audio signal to input. jARC j DIGITAL IN ≥ “On”: PCM is available. ≥ “Off”: DTS, PCM and Dolby Digital are available. Select “On” if the sound is cut off intermittently. Downmix Select the downmix system to enjoy multi-channel or 2-channel sound. ≥ Select “Surround encoded” to enjoy the surround sound. ≥ There is no downmix effect on the bitstream audio signal. ≥ The audio will be output in “Stereo” in the following cases: – AVCHD playback – Dolby TrueHD playback – Playback of secondary audio (including the button click sound). High Clarity Sound When connected to TV via the HDMI AV OUT terminal for outputting image, it produces clearer sound. ≥ Set to “Enable” and then set “High Clarity Sound” on the Playback menu to “On”. ( >31) Audio Delay Mis-sync between the video and audio is corrected by delaying the audio output. Speaker Refer to page 35 Status Messages Choose whether to show status messages automatically. On-screen Language Choose the language for menus and on-screen messages. Screen Saver Function This is to prevent burn-in on the screen. ≥When this is set to “On”: If there is no operation for 5 minutes or more, DIRECT NAVIGATOR screen switches to HOME menu automatically. ≥ While playing and pausing, etc., this function is not available. ≥ While playing music (CD-DA or MP3), after about 5 minutes DIRECT NAVIGATOR screen switches to a blank screen with “Screen Saver” message. Front Panel Display Changes the brightness of the unit’s display. ≥If “Auto” is selected, the display is dimmed but brightens when you perform some operations. License Information about the software used by this unit is displayed. Video AutoAutomatically selects the type of picture shown. FieldSelect if jittering occurs when “Auto” is selected. FrameSelect if small text or fine patterns cannot be seen clearly when “Auto” is selected. Audio Display VQT3M40~Body_mst.fm 32 ページ 2010年12月17日 金曜日 午前10時10分
Advanced operations 33 VQT3M40 3D Settings Press [OK] to show the following settings 3D Type Select the format of the connected TV. ≥Change the settings for 3D on the TV also when “Checker board” or “Side by side” is selected. 3D Playback Precautions Set to display or hide the 3D viewing warning screen when playing back the 3D compatible video software. TV Aspect Set to match the type of television connected. When connected to a 4:3 aspect television and playing 16:9 ratio image: When connected to a 16:9 widescreen television and playing 4:3 ratio image: HDMI Connection Press [OK] to show the following settings: HDMI Resolution The items supported by t he connected devices are indicated on the screen as “ ¢”. When any item without “ ¢” is selected, the images may be distorted. ≥ If “Auto” is selected, automatically selects the output resolution best suited to the connected television. ≥ To enjoy high-definition video up-converted to 1080p, you need to connect the unit directly to 1080p compatible HDTV (High Definition Television). If this unit is connected to an HDTV through other equipment, it must also be 1080p compatible. 24p Output When this unit is connected to a TV supporting 1080/24p output using an HDMI cable, movies and other material recorded at 24p are output at 24p. ≥When playing DVD-Video, set to “On” and then also set “24p” in “Video” ( >30) to “On”. ≥ When BD-Video images other than 24p are played, images are output at 60p. ≥ 24p : A progressive image recorded at a rate of 24 frames per second (motion-picture film). Many BD-Video movie contents are recorded in 24 frames/second in accordance with the film materials. HDMI Color Mode This setting is for selecting color-space conversion of the image signal when the unit is connected using an HDMI cable. HDMI Audio Output This setting selects whether or not to output audio from HDMI. ≥Audio will be output through the systems speakers when Off is selected. VIERA Link Set to use “HDAVI Control” function when connected with an HDMI cable to a device that supports “HDAVI Control”. ≥Select “Off” when you do not want to use “HDAVI Control”. Deep Color Output This setting is for selecting whether to use Deep Color output when a television that supports Deep Color is connected. Contents Type Flag Depending on the playback content, the TV will output adjusting to the optimal method when a TV that supports this function is connected. Power Off Link Select the desired power off link setting of this unit for VIERA Link operation ( >27). (This works depending on the settings of the connected VIERA Link “HDAVI Control” compatible equipment.) Video/Audio: When the TV is turned off, this unit will turn off automatically. Video: When the TV is turned off, this unit will turn off except during the following conditions: j CD or MP3 audio playback j iPod/iPhone mode j Radio mode j “AUX”,“ARC” or “D-IN” (DIGITAL IN) mode (non-selected TV AUDIO setting for VIERA Link) j “D-IN” (DIGITAL IN) mode (non-selected CABLE/ SATELLITE AUDIO setting for VIERA Link) TV Audio Input Select the TV audio input to work with the VIERA Link operations. TV / Device Connection 4:3The sides are cut off so the picture fills the screen. When playing BD-Video, video is output as “4:3 Letterbox”. 4:3 LetterboxBlack bands appear at the top and bottom of the picture. 16:9 Video is displayed as a 4:3 ratio image in the center of the screen. SC-BTT268_P_eng.book 33 ページ 2010年12月17日 金曜日 午前8時5分
34 VQT3M40 Network Easy Setting (>17) Network Settings Perform network-related settings individually. Press [OK] to show the following settings: IP Address / DNS Settings This is for checking the state of the network connection and setting the IP address and DNS-related. Press [OK] to show the respective setting. ≥“Connection Speed Setting” is enabled only when “Auto Detect Connection Speed” is turned “Off”. Proxy Server Settings This is for checking the state of connection with the Proxy server and performing settings. Press [OK] to show the respective setting. Internet Content Settings ( >29) (VIERA CAST) Press [OK] to show the following settings: Lock You can restrict the usage of VIERA CAST. ≥Follow the on-screen instructions. Enter the 4-digit password with the number buttons when the password screen is shown. Audio Auto Gain Control Volume that is different depending on the contents is adjusted automatically to the standard volume while using the VIERA CAST. ≥Depending on contents, this function effect will not work. ≥Select “Off” when t he audio is warped. Time Zone By selecting the time zone, it is possible to set the unit’s time to match your location. ≥Some VIERA CAST contents require the time zone to be set. Set the time zone if necessary. DST Select “On” when using Daylight Saving time. MAC Address Displays the MAC address of this unit. Remote Control Code Change the remote control code, when other Panasonic products react to this remote control. Quick Start* Speed of startup from power off is increased. ≥ Internal control unit will be powered when it is set to “On”, so contents of the following will be different from the time it is set to “Off”. – Idle power consumption will increase. (More about the power consumption >42) * Depending on the power conserving setting activated on the TV, this function may have less effect when the unit is started by the power on link function. ( >26) Easy setup ( >16) You can execute basic settings to optimize your home theater system. Restore Default Settings This returns all values in the Setup menu and the Playback menu, except for “Remote Control Code”, “On-screen Language”, “IP Address / DNS Settings”, “Proxy Server Settings”, “Lock”, “DVD-Video Ratings” and “BD-Video Ratings” etc. to the default settings. System Information Display firmware version of this unit. Firmware Update ( >17) Press [OK] to show the following settings: Automatic Update Check When this equipment remains connected to the Internet, it will check for the latest firmware version when it is turned on and you can update it if necessary. Update Now You can update the firmware manually. NetworkOthers SC-BTT268_P_eng.book 34 ページ 2010年12月18日 土曜日 午後1時5分
Advanced operations 35 VQT3M40 Delay time For optimum listening with 5.1-channel sound, all the speakers, except for the subwoofer, should be the same distance from the seating position. If either distance A or B is less than C, find the difference in the relevant table and adjust the delay time to make up for the difference. A B C : Primary listening distance A Approximate room dimensions B Actual speaker position C Ideal speaker position D Circle of constant primary listening distance 1Press [ 3,4, 2,1] to select the distance box ( ) and press [OK]. e.g., 5.1ch setting A Center (C) B Left Surround (LS), Right Surround (RS) 2Press [ 3,4] to select the setting and press [OK]. A Center speaker B Surround speaker Volume (Channel balance) ( ) (Effective when playing multi-channel audio) 1Select “Test” and press [OK]. A test signal is output. 2While listening to the test signal Press [ 3,4] to adjust the volume of each speaker. The volume can be adjusted between r6 dB to s6 dB. ≥ Set each speaker level according to the volume of the Front (L) and Front (R) speaker volume respectively. 3Press [OK]. The test signal stops. e.g., 5.1ch setting A Center (C) B Te s t C Left Surround (LS), Right Surround (RS) To finish the speaker setting Press [ 3,4, 2,1 ] to select “Complete” and press [OK]. Speaker settings DifferenceSetting Approx. 34 cm (1 ft. 1 in.)1.0 ms Approx. 68 cm (2 ft. 2 in.)2.0 ms Approx. 102 cm (3 ft. 4 in.)3.0 ms Approx. 136 cm (4 ft. 5 in.)4.0 ms Approx. 170 cm (5 ft. 6 in.)5.0 ms DifferenceSetting Approx. 170 cm (5 ft. 6 in.)5.0 ms Approx. 340 cm (11 ft. 1 in.)10.0 ms Approx. 510 cm (16 ft. 8 in.)15.0 ms : : L LS R SW C RS C RSLS A B C A B C D 0.0ms 0 00 0.0 0.0ms CompleteTe s t LS R L RS dB dB dB msC 0dBSW Adjusting speaker level dB0 0 00 0.0 0.0ms CompleteTe s t LS R L RS dB dB dB msC 0dBSW SC-BTT268_P_eng.book 35 ページ 2010年12月17日 金曜日 午前8時5分
36 VQT3M40 Optional speaker settings Speaker installation option You can attach all of the speakers (except subwoofer) to a wall. ≥The wall or pillar on which the speakers are to be attached should be capable of supporting 10 k g (22 lbs) per screw. Consult a qualified building contractor when attaching the speakers to a wall. Improper attachment may result in damage to the wall and speakers. ≥ Do not attempt to attach these speakers to walls using methods other than those described in this manual. 1Drive a screw (not supp lied) into the wall. 2Fit the speaker securely onto the screw(s) with the hole(s). Use the measurements indicated below to identify the screwing positions on the wall. ≥Leave at least 20 mm ( 25/32q) of space above the speaker and 10 mm (13/32q ) on each side to allow enough space for fitting the speaker. Front speaker, Surround speaker F 40 mm (1 9/16q) G 17.6 mm (11/16q) H 98.7 mm (3 7/8q) Center speaker I 23 mm ( 29/32q) J 95 mm to 97 mm (3 3/4q to 3 13/16q) K 26 mm (1 1/32q) L 16.7 mm (21/32q) M 63.7 mm (2 1/2q) Reference Troubleshooting guide Before requesting service, please perform the following steps. The following do not indicate a problem with this unit: jRegular disc rotating sounds. jImage disturbance during search. jImage disturbance when replacing 3D discs. ∫Unit does not respond to the remote control or front panel buttons. Press and hold [POWER Í/I] on the main unit for 5 seconds. jIf still unable to power the unit off, disconnect the power cord, wait 1 minute, then reconnect the power cord. ∫ Cannot eject disc. The unit may have a problem. While the unit is off, press and hold [ 9] on the remote control and [ 34) To return all settings to the factory preset ≥Reset the unit as follows: While the unit is off, press and hold [+ VOLUME], [ 9) ≥ The remote control and main unit are using different codes. If “SET ” is displayed on the unit’s display when a button is pressed on the remote control, change the code on the remote control. ( >34) Disc cannot be played. ≥The disc is dirty. ( >9) ≥Check the region code. Attaching to a wall A At least 30 mm (1 3/16q) B ‰ 4.0 mm (5/32q) C ‰ 7.0 mm to ‰ 9.4 mm ( 9/32q to 3/8q) D Wall or pillar E 5.5 mm to 7.5 mm ( 7/32q to 5/16q) e.g., Front speaker DO NOTDO ≥ In this position, the speaker will likely fall if moved to the left or right.≥Move the speaker so that the screw is in this position. \b \f \f Do you have the latest firmware installed? Firmware updates may be released to correct operating irregularities that are discovered with certain movies. ( >17) 4 Make the following checks and visit our website for more information. http://www.panasonic.com/help Enter the model number. 4 Or visit our website to find a service center. You can find a service center near you easily on our website. Other support information: “Customer Services Directory (United States and Puerto Rico)” (>43) General operation SC-BTT268_P_eng.book 36 ページ 2010年12月24日 金曜日 午前11時19分
ReferenceOptional speaker settings 37 VQT3M40 Still pictures (JPEG) do not playback normally. ≥The images that were edited on the PC, such as Progressive JPEG, etc., may not playback. The TV tuner mode is not displayed when the TV is switched on. ≥This phenomenon may occur, depending on the TV setting, when “Quick Start” is set to “On”. ≥ Depending on the TV, this phenomenon may be prevented by reconnecting the HDMI cable to a different HDMI input terminal or by changing the HDMI auto connection setting. You have forgotten your ratings password. You want to cancel the ratings level. The ratings level returns to the factory preset. 1 While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds. j“00 RET” is displayed on the unit’s display. 2Repeatedly press [1] (right) on the remote control or [POWER Í/I] on the unit until “03 VL” is displayed on the unit’s display. 3 Press [OK] on the remote control or [ 15) The unit switches to standby mode. ≥This unit will automatically turn to standby mode after 30 minutes if it is inactive. ( >7) ≥ When the time set for the sleep timer has passed, the power will be turned off. ( >6) ≥ One of the unit’s safety devices is activated. Press [POWER Í/I] on the main unit to turn the unit on. This unit is turned off when the input for the TV is switched. ≥This is a normal phenomenon when using VIERA Link (HDAVI Control 4 or later). For details please read the operating instructions for the TV. The unit does not turn off. 1Press and hold [POWER Í/I] on the main unit for 5 seconds. (If still unable to power the unit off, disconnect the power cord, wait 1 minute, then reconnect the power cord.) 2 Reset the unit as follows: While the unit is off, press and hold [+ VOLUME], [< OPEN/CLOSE] and [POWER Í/I] on the main unit at the same time for more than 5 seconds. The display is dim. ≥ Change “Front Panel Display” in the Setup menu. ( >32) The images from this unit do not appear on the TV. Picture is distorted. Jittering occurs. ≥ An incorrect resolution is selected in “HDMI Resolution”. Reset the setting as follows: 1 While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds. j“00 RET” is displayed on the unit’s display. 2Repeatedly press [1] (right) on the remote control or [POWER Í/I] on the unit until “04 PRG” is displayed on the unit’s display. 3 Press and hold [OK] on the remote control or [ 33) j When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream, select “Yes” in “Restore Default Settings” and make proper settings. (> 34) ≥ When “3D BD-Video Playback” in the Setup menu is set to “Automatic”, images may not be output depending on the connection method. After removing the disc from this unit, select “Set before play” in the Setup menu, and select “2D Playback” in the setup screen displayed when playing 3D discs. ( >31) Video is not output. ≥Set “High Clarity Sound” in the Playback menu to “Off” to use the VIDEO OUT terminal. ( >31) Video is not output in high-definition. ≥Confirm that “HDMI Resolution” in the Setup menu is set properly. ( >33) 3D video is not output. ≥Are the settings on this unit and the TV correct? ( >22) 3D video is not output correctly as 2D. ≥Select “Set before play” in the Setup menu, and select “2D Playback” in the setup screen displayed when playing 3D discs. ( >31) ≥ Discs that have recorded titles with Side by side (2 screen structure) and that can be enjoyed in 3D are played back in accordance with the settings of the TV. No subtitles. ≥When progressive output is on, closed captions/subtitles cannot be displayed. The subtitles overlap closed captions recorded on discs. ≥Turn off the subtitles or turn off the closed caption setting on the TV. (> 30) A black band is displayed around the edge of the screen. The aspect ratio of the screen is abnormal. ≥Confirm the “TV Aspect” is set properly. ( >33) ≥ Adjust the aspect setting on the television. Power Displays TV screen and video VQT3M40~Body_mst.fm 37 ページ 2010年12月24日 金曜日 午後8時0分
38 VQT3M40 No sound. Low volume. Distorted sound. Cannot hear the desired audio type. ≥Check connections to s peakers and other equipment. (> 10s 15) ≥ Ensure the speaker settings for your speakers are correct. (>35) ≥To output audio from a device connected with an HDMI cable, set “HDMI Audio Output” to “On” in the Setup menu. (>33)≥ When “BD-Video Secondary Audio” is set to “On”, Dolby TrueHD, Dolby Digital Plus, DTS-HD Master Audio and DTS-HD High Resolution Audio are output as Dolby Digital or DTS Digital Surround. ≥ Re-master will not work when the bitstream signal is output from the HDMI AV OUT terminal. ( >31) ≥ Depending on the connected equipment, the sound may be distorted if this unit is connected with an HDMI cable. ≥ The multi-channel audio from a device connected to the TV is not output in it’s original multi-channel form. jIf the device has an optical audio output terminal, connect the device to this unit’s “OPTICAL” terminal. ( >14, 25) No surround sound. ≥Press [SURROUND] to select a surround effect. ( >19) Cannot switch audio. ≥When audio is output from the HDMI AV OUT terminal, set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “PCM”. ( >32) No sound from the TV. ≥Press [EXT-IN] to select the corresponding source. (> 18) ≥ When connecting the unit to a TV using an HDMI cable, check whether the HDMI terminal on the TV is labeled “HDMI (ARC)”. If not labeled in this way, connect using the HDMI cable in combination with an optical digital audio cable.( >12, 13)≥ If there is no sound from the equipment connected to this unit’s DIGITAL AUDIO IN terminal, please make sure that the optical audio output of the equipment is set to PCM. Cannot charge or operate. ≥ Check that the iPod/iPhone is connected firmly. ( >27) ≥ The battery of the iPod/iPhone is depleted. Charge the iPod/ iPhone, and then operate again. ≥ When unexpected operation occurs while using the iPod/iPhone, connect the iPod/iPhone again or try to restart the iPod/iPhone. Cannot display iPod/iPhone videos/photos on the TV. ≥Make sure that TV is connected to the VIDEO OUT terminal on this unit. ( >12) ≥ Operate the iPod/iPhone menu to make the appropriate video/photo output settings for your TV. (Refer to operating instructions for your iPod/iPhone.) The TV input channel unintentionally changes to HDMI input. ≥When the main unit is connected with an “HDAVI Control” compatible TV and VIDEO IN is selected for iPod/iPhone video or photo playback, the TV input channel will automatically change to the HDMI input channel when [HOME] is pressed. jRe-select the TV’s VIDEO IN input channel. Distorted sound or noise is heard. ≥ Adjust the position of the antenna. ≥ Use an outdoor antenna. ( >11 ) A beat sound is heard. ≥Try to keep a certain amount of distance between the antenna and the TV. I can’t connect to the network. ≥ Confirm the network connection and settings. ( >15, 17, 34) ≥ Check the operating instructions for each device and connect accordingly. BD-Video or DVD-Video is not played. ≥ Ensure the disc is for the correct BD-Video region code or DVD-Video region number, and is not defective. ( >8) ≥ You have set a ratings level to limit BD-Video or DVD-Video play. Change this setting. ( >31) ≥ Some BD-Video can only be output with HDMI. I cannot play back BD-Live. ≥The SD card is write-protected. ( >9) ≥ Confirm that this unit is connected to the broadband Internet. (> 15) ≥ Confirm the “BD-Live Internet Access” settings. (> 32) ≥ Confirm an SD Card is inserted into the SD Card slot. ( >18) Alternative soundtrack and subtitles cannot be selected. ≥The languages are not recorded on the disc. ≥ You may not be able to use the playback menu to change the soundtrack and subtitles on some discs. Use the disc’s menus to make changes. ( >20) Angle cannot be changed. ≥Angles can only be changed during scenes where different angles are recorded. Sound iPod/iPhone operation Radio Network Other difficulties with playback SC-BTT268_P_eng.book 38 ページ 2010年12月17日 金曜日 午前8時5分
Reference 39 VQT3M40 Messages The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use. Cannot play. ≥You inserted an incompatible disc. (Discs recorded in PAL video, etc.) Cannot display on this unit. ≥You tried to play a non-compatible image. No disc is inserted. ≥The disc may be upside down. $ This operation is not available. ≥ Some operations are unsupported by the unit. For example; jBD-Video: During playback, reverse slow-motion or reverse frame-by-frame is not possible. IP address is not set. ≥The “IP Address” in “IP Address / DNS Settings” is “---. ---. ---. ---”. Set the “IP Address”, “Subnet Mask”, and “Default Gateway”. (Select the automatic address acquisition if necessary.) No Video ≥Depending on the connected iPod/iPhone, video menu may not be available on the TV. Select “ALL” on the unit’s display and operate video playback from your iPod/iPhone menu. (> 29) F99 ≥ The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on. U59 ≥ The unit is hot. The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears. Select a position with good ventilation when installing the unit. Do not block the ventilation hole on the rear and side of the unit. HDMI ONLY ≥Some BD-Video discs can only be output with HDMI. NET ≥While connecting to a network. No PLAY ≥There is a viewing restriction on a BD-Video or DVD-Video. (> 31) No READ ≥The media is dirty or badly scratched. The unit cannot play. PLEASE WAIT ≥The unit is carrying out an internal process.This is not a malfunction. You cannot operate the unit while “PLEASE WAIT” is displayed. SET (“ ” stands for a number.) ≥ The remote control and main unit are using different codes. Change the code on the remote control. Press and hold [OK] and the indicated number button at the same time for more than 5 seconds. H or F (“ ” stands for a number.) ≥ Check and correct the speaker cable connections. ≥ There is something unusual. ≥ Check the unit using the troubleshooting guide. If the service number does not disappear, do the following. 1 Disconnect the plug from the household AC outlet, wait a few seconds, then reconnect it. 2 Press [POWER Í/I] to turn the power on. If the service number does not disappear despite doing the above, request service from the dealer. Inform the dealer of the service number when requesting service. UPD / (“ ” stands for a number.) ≥ The firmware is being updated. Please do not turn off power. IPOD OVER CURRENT ERROR ≥The iPod/iPhone is drawing too much power. Remove the iPod/iPhone, and turn the unit off and on again. START ≥The system is being restarted during the firmware update. Please do not turn off power. FINISH ≥The firmware update is completed. NOT CONDITIONAL ≥The requested operation cannot be conducted. On the television On the unit’s display VQT3M40~Body_mst.fm 39 ページ 2010年12月24日 金曜日 午後8時1分
40 VQT3M40 Supplemental information ∫Display languages list ∫ Language code list ≥With certain recording states and folder structures, the play order may differ or playback may not be possible. DisplayLanguageDisplayLanguageDisplayLanguage LanguageCodeLanguageCodeLanguageCode ENG FRA DEU ITA ESP NLD SVE NOR DAN POR RUS English French German Italian Spanish Dutch Swedish Norwegian Danish Portuguese Russian ARA HIN PER IND MRI BUL RUM GRE TUR JPN CHI KOR MAL VIE THA POL CES SLK HUN FIN Japanese Chinese Korean Malay Vietnamese Thai Polish Czech Slovak Hungarian FinnishArabic Hindi Persian Indonesian Maori Bulgarian Romanian Greek Turkish Others Abkhazian 6566 Afar: 6565 Afrikaans: 6570 Albanian: 8381 Amharic :6577 Arabic: 6582 Armenian: 7289 Assamese: 6583 Aymara: 6589 Azerbaijani: 6590 Bashkir: 6665 Basque: 6985 Bengali; Bangla: 6678 Bhutani: 6890 Bihari: 6672 Breton: 6682 Bulgarian: 6671 Burmese: 7789 Byelorussian: 6669 Cambodian: 7577 Catalan: 6765 Chinese: 9072 Corsican: 6779 Croatian: 7282 Czech: 6783 Danish: 6865 Dutch: 7876 English: 6978 Esperanto: 6979 Estonian: 6984 Faroese: 7079 Fiji: 7074 Finnish: 7073 French: 7082 Frisian: 7089 Galician: 7176 Georgian: 7565 German: 6869 Greek: 6976 Greenlandic: 7576 Guarani: 7178 Gujarati: 7185 Hausa: 7265 Hebrew: 7387 Hindi: 7273 Hungarian: 7285 Icelandic: 7383 Indonesian: 7378 Interlingua: 7365 Irish: 7165 Italian: 7384 Japanese: 7465 Javanese: 7487 Kannada: 7578 Kashmiri: 7583 Kazakh: 7575 Kirghiz: 7589 Korean: 7579 Kurdish: 7585 Laotian: 7679 Latin: 7665 Latvian, Lettish: 7686 Lingala: 7678 Lithuanian: 7684 Macedonian: 7775 Malagasy: 7771 Malay: 7783 Malayalam: 7776 Maltese: 7784 Maori: 7773 Marathi: 7782 Moldavian: 7779 Mongolian: 7778 Nauru: 7865 Nepali: 7869 Norwegian: 7879 Oriya: 7982 Pashto, Pushto: 8083 Persian: 7065 Polish: 8076 Portuguese: 8084 Punjabi: 8065 Quechua: 8185 Rhaeto-Romance: 8277 Romanian: 8279 Russian: 8285 Samoan: 8377 Sanskrit: 8365 Scots Gaelic: 7168 Serbian: 8382 Serbo-Croatian: 8372 Shona: 8378 Sindhi: 8368 Singhalese: 8373 Slovak: 8375 Slovenian: 8376 Somali: 8379 Spanish: 6983 Sundanese: 8385 Swahili: 8387 Swedish: 8386 Tagalog: 8476 Tajik: 8471 Tamil: 8465 Tatar: 8484 Telugu: 8469 Thai: 8472 Tibetan: 6679 Tigrinya: 8473 Tonga: 8479 Turkish: 8482 Turkmen: 8475 Twi: 8487 Ukrainian: 8575 Urdu: 8582 Uzbek: 8590 Vietnamese: 8673 Volapük: 8679 Welsh: 6789 Wolof: 8779 Xhosa: 8872 Yiddish: 7473 Yoruba: 8979 Zulu: 9085 File format File formatExtensionReference MP3 “.MP3”, “.mp3“ ID3 tags (Only titles and the names of artists) JPEG“.JPG”, “.jpg“ ≥ MOTION JPEG and Progressive JPEG is not supported ≥ You may not be able to play back the file if you have edited the folder structure or the file name on a PC or other device. SC-BTT268_P_eng.book 40 ページ 2010年12月17日 金曜日 午前8時5分