Panasonic Bluray Disc Home Theater Sound System Sc Bt200 Operating Instructions

							21
RQT9508
[AVCHD] [MPEG2]
It is possible to playback the High Definition (AVCHD format) video 
recorded on a Panasonic High definition Video Camera on a 
DVD-RAM/R/RW/R DL/+R/+RW/+R DL, or SD card and Standard 
Definition (MPEG2 format) Video recorded on the Panasonic SD Video 
Camera on a SD card.
1 Insert a disc or SD card. (> 19)≥The “Video (AVCHD)” or “Video (MPEG-2)” screen is displayed.
≥ If media containing data in different file formats is inserted, the 
file selection menu may be displayed.
Press [ 3,4] to select “Play Video (AVCHD)” or “Play Video 
(MPEG-2)” and press [OK].
2 Press [ 3,4,2 ,1 ] to select the title and press 
[OK].
Status messages
The status messages give you information about what is currently 
being played. Each time you press [STATUS], the information 
displayed will change.
Screen Aspect
When black bars are shown at the top, bottom, left, and right sides of 
the screen, you can enlarge the image to fill the screen.
1 Press [SUB MENU].
2 Press [ 3,4] to select “Screen Aspect” and press [OK].
3 Press [ 2,1] to select “Side cut” or “Zoom” and press [OK].
Normal: Normal output
Side cut: The black bars on the right and left sides of the 16:9  image disappear and the image is enlarged. Please note 
that the right and left sides of the image are cut off when 
the black bar is not displayed.
Zoom: The black bars on the top and bottom sides of the 4:3  image disappear and the image is enlarged. Please note 
that the top and bottom sides of the image are cut off 
when the black bar is not displayed.
≥ [BD-V]  [DVD-V]: “Side cut” does not have any effect.
≥ When “TV Aspect” (> 39) is set to “4:3” or “4:3 Letterbox”, the 
“Zoom” effect is disabled.
Setting the sleep timer
1 Press and hold [–SLEEP] for 3 seconds.
2 While “SLEEP ££” is displayed, 
Press [–SLEEP] several times to select the time (in minutes).
SLEEP 30  ) SLEEP 60 )  SLEEP 90 )SLEEP 120  )OFF
^""""""""""""""""""""""""""""""""b
e.g.
To confirm the remaining time
Press and hold [–SLEEP] for 3 seconds.
≥ The sleep timer cannot be set while the Setup menu is displayed.
≥ The sleep timer will be canceled in the following cases.
– When the sleep timer is set to “OFF”.
– When this unit is turned off from the remote control, main unit or via  the VIERA Link.
STATUS
Play BD-Video 
\f T1     C1     0:05.14 0:20.52 

Type of disc Play status
T:  T i t l e
C: Chapter
PL: Playlist Items change 
depending on the 
disc played.
Elapsed time in the title
Current position Total time
No display
Depending on the kind of disc or the playback status, 
this display may not appear.
e.g.,  [BD-V]
-SLEEP
DISPLAY
SLP
Playing video recorded on a Video 
Camera or Video Recorder
≥It may pause for a few seconds between images when 
editing such as partial deletion is performed.
≥ High definition video (transfer rate of 18 Mbps or faster) 
cannot be played back correctly if it was recorded on a 
DVD compatible to double speed or slower.
To return to the previous screen
Press [RETURN].
To exit the screen
Press [TOP MENU/DIRECT NAVIGATOR].
To switch from other menus to AVCHD or MPEG2 menu
(If the media contains data in different file formats)
1) Press [START].
2) Press [ 3,4] to select “Menu” and press [OK].
3) Press [ 3,4] to select “Play Video (AVCHD)” or “Play 
Video (MPEG-2)” and press [OK].
SD Card
Play Video (AVCHD)
Select an action or press [RETURN].
Play Pictures (JPEG)
OK
RETURN
SUB 
MENU
Play Video (MPEG-2)
e.g.,  [SD]
NOTE
TIPS
Playback
BT300.book  21 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							22
RQT9508
Enjoying BD-LIVE or BONUSVIEW in 
BD-Video
[BD-V]What is BONUSVIEW?
BONUSVIEW allows you to enjoy functions such as picture-in-picture or secondary audio etc., with BD-Video supporting BD-ROM Profile 1 version 
1.1/ Final Standard Profile.
What is BD-Live?
In addition to the BONUSVIEW function, BD-Video supporting BD-ROM Profile 2 that has a network extension function allows you to  enjoy more 
functions such as subtitles, exclusive images and online games by connecting this unit to the Internet. In order to use the Int ernet feature, you must 
have this unit connected to a broadband network ( >14).
≥ These discs may not be on sale in certain regions.
≥ The usable functions and the operating method may vary with each disc, please refer to the instructions on the disc and/or visi t their website.
Playing secondary video (picture-in-picture) and secondary audio
Secondary video can be played from a disc compatible with the picture-in-picture function. For the playback method, refer to the instructions for the disc.
To turn on/off secondary video
1Press [DISPLAY].
2 Press [ 3,4] to select the “Disc” menu and 
press [ 1].
3 Press [ 3,4] to select the “Signal Type” menu 
and press [OK].
4 Press [ 3,4] to select the “Video” under 
“Secondary Video” menu and press [ 1].
5 Press [ 3,4] to select the “On” or “Off”.
6 Press [RETURN] to exit.
To turn on/off audio with the secondary video
1 Press [DISPLAY].
2 Press [ 3,4] to select the “Disc” menu and press [1 ].
3 Press [ 3,4] to select the “Signal Type” menu and press [OK].
4 Press [ 3,4] to select the “Soundtrack” under “Secondary Video” menu and 
press [ 1].
5Press [3,4] to select the “On” or “Off”.
When “On” is selected, press [1] and then press [3,4] to select the language.6 Press [RETURN] to exit.
≥Discs may not always be played back according 
to the settings on this unit, as certain playback 
formats are prioritized on certain discs.
≥ Only the primary video is played during search/
slow-motion or frame-by-frame.
≥ When “BD-Video Secondary Audio” in “Digital 
Audio Output” is set to “Off”, secondary audio will 
not be played. Please check that “BD-Video 
Secondary Audio” is set to “On” ( >38).
≥ When the secondary video is turned off, the 
secondary audio is not played.
Secondary video
Primary videoNOTE
Enjoying BD-Live discs with Internet
Many BD-Live compatible discs require content to be downloaded onto an SD 
card ( >55, Local storage) in order to access the available BD-Live features.
≥ An SD card with 1 GB or more of free space (SD Speed Class Rating 2 or higher) 
needs to be inserted prior to inserting the BD-Live compatible disc.
Some BD-Live content available on the Blu-ray discs may require an Internet 
account to be created in order to a ccess the BD-Live content. Follow the 
screen display or instruction manual of the disc for information on acquiring 
an account.
Preparation≥ Connect to the network. ( >14)
1 Insert an SD card. ( >19)≥If the SD card menu screen is displayed, press [BD/SD] on the remote 
control, select BD/DVD.
2 Insert the disc. ( >19)≥For operation method, refer to the instructions on the disc.
To use the above functions, it is recommended that you format the card on this unit.
Format the card using the following procedures.
BD-Video data, such as secondary video recorded on the card, can also be erased 
with the following procedures.
Formatting SD cards/Deleting dataIt is impossible to restore data after formatting the card or erasing the data.
Once a card is formatted, all data including those recorded on the PC is erased as 
well, even if the data were protected with other equipment.
Confirm whether the card can be formatted.
1) Insert an SD card ( >19).
2) Press [START].
3) Press [3,4] to select “Other Functions” and 
press [OK].
4) Press [ 3,4 ] to select “Card Management” and 
press [OK].
5) Press [ 3,4] to select “BD-Video Data Erase” 
or “Format SD Card” and press [OK].
6) Press [ 2,1] to select “Yes” and press [OK].
7) Press [ 2,1] to select “Start” and press [OK].
≥If you experience any problems, first, try 
formatting the SD card in this unit.
≥ A message may be displayed when the SD card 
doesnt have enough storage capacity for 
BD-Live content.
Please make space available on the current SD 
card, or insert another SD card.
≥ While using this feature, do not remove the SD 
card. Doing so will cause playback to stop.
≥ The unit must be connected to the Internet and 
set up ( >33) to use the BD-Live functions. 
“BD-Live Internet Access” may need to be 
changed for certain discs ( >37).
≥ When discs supporting BD-Live are played 
back, the player or disc IDs may be sent to the 
content provider via the Internet. You can 
restrict Internet access. ( > 37 “BD-Live Internet 
Access”)
≥ The unit is connected to the Internet when 
BD-Live functions are used, generating 
communication charges.
≥ The playback may be paused depending on the 
communication environment.
Some functions may be disabled to prevent 
skipping to sections that have not been 
downloaded, etc.
Card Management No. of Files    6
Free space    300 MB
SD card
Format this SD Card.OK
RETURN
BD-Video Data EraseFormat SD Card
NOTE
Playback
BT300.book  22 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							23
RQT9508
Playing still pictures
[JPEG]
Playback of a BD-RE, DVD-RAM/R/R DL, CD-R/RW, or SD card with still pictures recorded.
(About structure of folders D 44, “Structure of folders that can play back on this unit”)
1 Insert a disc or an SD card. ( >19)
BD-RE, DVD-RAM“Album View” screen is displayed.
≥When the “Title View” screen is displayed, press [G] to 
switch to the “Album View” screen.
≥ If the DVD-RAM containing both JPEG and AVCHD format is inserted, the 
file selection menu may be displayed.
DVD-R/R DL, CD-R/RW, SD card≥If a media containing data in different file formats is inserted, the file 
selection menu may be displayed.
Press [ 3,4] to select “Play Pictures (JPEG)” and press [OK].
“Picture View” screen is displayed
B Go to step  3
2Press [ 3,4 ,2 ,1 ] to select the album and press [OK].
3 Press [ 3,4 ,2 ,1 ] to select the still picture and press 
[OK].
≥ Small-sized still pictures are displayed with a 
frame.
≥Press [ 2,1] to display the previous or next still 
picture.
≥ Press [SKIP :, SKIP 9] to show other 
pages.
To return to the previous screen
Press [RETURN].
To exit the screen
Press [TOP MENU/DIRECT NAVIGATOR].
DVD-RAM/R/R DL, CD-R/RW, SD card
To switch from other menus to JPEG menu
(If the media contains data in different file 
formats)
1) Press [START].
2) Press [ 3,4] to select “Menu” and press 
[OK].
3) Press [ 3,4] to select “Play Pictures (JPEG)” 
and press [OK].
e.g.,  [SD]
SD Card
Play Video (AVCHD)
Select an action or press [RETURN].
Play Pictures (JPEG)
OK
RETURN
SUB 
MENU
Play Video (MPEG-2)
e.g.,  [SD]
RG
DIRECT NAVIGATORAlbum ViewDVD-RAM(VR)Video Picture
OKPress [OK] to go to Picture View  Previous Next SlideshowRETURNVideo
Picture Page  02/02
 Total 8
106_DVD
 Total 1312/9/2006 
SUB
MENU
e.g.
NOTE
TIPS
Playback
BT300.book  23 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							24
RQT9508
Playing still pictures 
Useful functions during still picture play
Start Slideshow
You can display still pictures one by one at a constant interval.
BD-RE, DVD-RAM1While the “Album View” screen is displayed
Press [ 3,4,2, 1] to select the album and press [SUB MENU].
2 Press [ 3,4] to select “Start Slideshow” and press [OK].
≥ You can also start slideshow by pressing [ 1PLAY] after selecting 
the album.
DVD-R/R DL, CD-R/RW, SD card1 While the “Picture View” screen is displayed
Press [SUB MENU].
2 Press [ 3,4] to select “Start Slideshow” and press [OK].
To stop slideshow
Press [ ∫STOP].
Slideshow settings
After performing step 1 in “Start Slideshow” above,
2 Press [ 3,4] to select “Slideshow Setting” and press [OK].
3 To change the display interval
Press [ 3,4] to select “Display interval” and press [ 2,1] to 
select the interval (“Normal”, “Long” or “Short”).
≥ When a still picture with a large number of pixels is played, the 
display interval may become longer. Even if the setting is 
changed, the display interval may not become shorter.
To set display method
Press [ 3,4] to select “Transition Effect” and press [ 2,1] to 
select “Fade”, “Motion” or “Random”.
“Fade”: Pictures are changed by fading out and fading in.
“Motion”: Pictures are changed by fading out and fading in,  while it is enlarged, reduced, or moved up or down.
“Random”: In addition to “Motion”, pictures are changed by 
various methods.
To repeat slideshow
Press [ 3,4] to select “Repeat Play” and press [ 2,1] to select 
“On” or “Off”.
To listen to Background Music
Music files on an iPod or a music CD can be played back as 
Background music during the slideshow.
Press [ 3,4] to select “Soundtrack” and press [ 2,1] to select 
“On” or “Off”.
≥ You cannot search or skip the music.
≥ When the slideshow stops, playback of the music also stops.
≥ Playback of the music files will be in the following order:
[CD] : Order of “Music list” display in repeat mode.
iPod: The music files will be played back in repeat mode.
≥ When both a music CD and an iPod is inserted to this unit, the 
iPod has a priority to be played back as Background Music.
4 Press [ 3,4,2, 1] to select “Set” and press [OK].
Rotate
1While playing (except for slideshows)
Press [SUB MENU].
2 Press [ 3,4] to select “Rotate Right” or “Rotate Left” and press 
[OK].
≥ The rotation information will be stored until the unit is turned off or 
the media is removed.
Zoom out
This function is only available for small-sized still pictures.
1 While playing (except for slideshows)
Press [SUB MENU].
2 Press [ 3,4] to select “Zoom out” and press [OK].
≥ To cancel “Zoom out”, press [ 3,4] to select “Zoom in” in step 2 
and press [OK].
≥ The zoom-out information will not be stored.
To select the still pictures in another folder
BD-RE, DVD-RAMTo switch to another higher folder
(Only if there is a multiple number of higher folders recognizable)
1 While the “Album View” screen is displayed
Press [SUB MENU].
2 Press [ 3,4] to select “Select Root folder” and press [OK].
3 Press [ 2,1] to select the higher folder and press [OK].
DVD-R/R DL, CD-R/RW1 While the “Picture View” screen is displayed
Press [SUB MENU].
2 Press [ 3,4] to select “Select Folder” and press [OK].
3 Press [ 3,4] to select a folder and press [OK].
The “Picture View” screen for the folder appears.
To show the picture properties
While playing
Press [STATUS] twice.
To exit, press [STATUS].
\JPEG\DCIM001
OK
RETURN
Select Root folder
Change the Album folder to be accessed.
Press [OK] to confirm
PicturesFolder selection
CD(JPEG)
    001 
        002 
        003 
        004 
        005 
        006  
        007 
        
008        009 
        010 
      
    103 
        104 
        105
021216_0026   F  2/25
OK RETURN
Photo     11/12/2007                    Total        3/9
Shooting date
e.g., JPEG on DVD-RAM
Playback
BT300.book  24 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							25
RQT9508
Playing music
[CD] [MP3]
You can generally play any available music CD or MP3 file recorded onto a DVD-R/R DL and CD-R/RW.
(About structure of folders  D 44 , “Structure of folders that can play back on this unit”)
1 Insert a disc. (> 19)
≥If a media containing data in different file 
formats is inserted, the file selection 
menu may be displayed. Press [ 3,4] to 
select “Play Music (MP3)” and press 
[OK].
2 Press [ 3,4 ] to select the track and press [OK].Play starts on the selected track.
To switch from other menus to MP3 menu
(If the media contains data in different file 
formats)
1) Press [START].
2) Press [ 3,4] to select “Menu” and press 
[OK].
3) Press [ 3,4] to select “Play Music (MP3)” 
and press [OK].
≥ You can use search and skip functions. ( >20)
≥ When the “Screen Saver Function” is set to 
“On” (> 38), the screen switches to Screen 
Saver mode if there is no operation for 5 
minutes after starting playback. (Playback 
continues.)SLPe.g.
CD
Select an action or press [RETURN].OK
RETURNSUB
MENU
Play Pictures (JPEG)Play Music (MP3)
 0.09  4.30
01
02
03
04
05
DIRECT NAVIGATORMusic list
CD
No. Track Name Play Time Track1
Track1 4min30sec 
3min41sec 
4min30sec 
3min11sec 
5min  2sec 
Track25 Tracks / Total Play Time 20min54sec
Track3
Track4
Track5
Play RETURN“ ” indicates the track currently playing.
e.g.,  [CD]
TIPS
[MP3] Playing a track in another folder1 While the “Music list” is displayed
Press [SUB MENU], press [ 3,4] to select “Select Folder” and press [OK].
2 Press [ 3,4 ] to select a folder and press [OK].
The “Music list” for the folder appears.≥ You cannot select folders that contain no 
compatible tracks.
To return to the previous screen
Press [RETURN].
DIRECT NAVIGATORSelect Folder
CD(MP3)
    001 My favorite
        002 Brazilian pops
        003 Chinese pops
        004 Czech pops
        005 Hungarian pops
        006 Liner notes
        007 Japanese pops
        
008 Mexican pops        009 Philippine pops
        010 Swedish pops
            011 Momoko
    012 Standard number
        013 Piano solo
        014Vocal
MP3 music   F  8/25
OK RETURN
 Selected folder No. /Total 
folders
If the folder has no track, “– –” 
is displayed as folder number.
NOTE
TIPS
Playing music continuously even after turning off power to the 
TV≥ Sound may be discontinued for several seconds 
when the power to the TV is turned off.
When the unit is connected to a Panasonic TV (VIERA) that supports HDAVI 
Control 2 or later and another device supports VIERA Link, the unit is turned 
off if the power to the TV is turned off, since “Power off link” ( >29) operates.
The following operations make it possible to keep the power of the unit ON 
and to play music continuously. Set “Power Off Link” to “Video” ( >39).
NOTE
Playback
BT300.book  25 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							26
RQT9508
Listening to the Radio
Up to 30 stations can be set in each band, FM and AM.
1Press [RADIO] to select “ FM” or “ AM”.
2 Press [STATUS] to select the position to start the 
auto preset search.
Each time you press the button:
LOWEST (factory preset):
To begin auto preset with the lowest frequency.
(FM: 87.9 or 87.5, AM: 520)
CURRENT:
To begin auto preset with the current frequency.*
* To change the frequency, refer to “Manual tuning”. ( Bright)
3 Press and hold [OK].
Release the button when “AUTO” is 
displayed.
The tuner starts to preset all the stations it 
can receive into the channels in ascending 
order.
≥ “SET OK” is displayed when the stations are set, and the radio tunes 
to the last preset station.
≥ “ERROR” is displayed when automatic presetting is unsuccessful. 
Preset the stations manually. ( Bright)
1 Press [RADIO] to select “ FM” or “ AM”.
2 Press the numbered buttons to select the 
channel.
To select a 1-digit number
e.g., 1: [1] >[OK].
To select a 2-digit number
e.g., 12: [1]  B [2]
Alternatively, press [ W,X ] or [ 2,1 ].
When a stereo FM broadcast is being received, 
“ST” lights in the display.
≥ The FM/AM setting is also shown on the TV display.
∫ If noise is excessiveWhen FM is selected
Press [AUDIO] to display “MONO”.
Press the button again to cancel the 
mode.
≥The mode is also canceled when you change the frequency.
≥ This setting can be preset for each broadcasting station. When 
“MONO” appears, follow procedures  1 and 2 in “Presetting stations 
manually”. ( >below)
When AM is selected
Press [AUDIO] to select “AM BP1” or “AM BP2” (whichever 
receives the better quality).
Each time you press the button:
AM BP1 (.AM BP2 (BP=Beat Proof)
1 Press [RADIO] to select “ FM” or “ AM”.
2 Press [SEARCH 6] or [SEARCH 5] to select 
the frequency.
≥ Main unit:
Press [ XTUNE W] to select the frequency.
≥ When a radio broadcast is being 
received, “T” lights in the display.
≥ To start automatic tuning, press 
and hold [SEARCH 6] or 
[SEARCH 5] (main unit: [ XTUNE W]) until the frequency 
starts scrolling. 
Tuning stops when a station is found.
∫ Presetting stations manuallyUp to 30 stations can be set in each band, FM and AM.
1 While listening to the radio broadcast
Press [OK].
2 While “P” is flashing on the display
Press the numbered buttons to select a channel.
To select a 1-digit number
e.g., 1: [1] >[OK].
To select a 2-digit number
e.g., 12: [1]  B [2]
A station previously stored is overwritten when another station is 
stored in the same channel preset.
FM frequency step
Main unit:
The factory setting is set to 0.2 MHz, it can be changed to receive broadcasts allocated in 0.1 MHz. You may need to change this  setting 
if the tuner seems to skip over the correct frequency for stations in your area.
1 Press [SELECTOR] to select “FM”.
2 Press and hold [SELECTOR].
After a few seconds the display changes to show the current lowest frequency. Continue to hold the button down. The lowest freq uency changes 
and the step is changed.
To return to the original settings, repeat steps 1 and  2.
Setting up the radio
Presetting stations automatically
[email protected]
456
78
0
9
OK
EXT-INRADIO
STATUSAUDIO
ABCDEF
JKLMNO
TUV
GHIQRSP
XYZ W
_,
SEARCHSEARCH
Numbered
buttons
RADIO
AUDIOSTATUS
,
SEARCH
SEARCH
OK
TUNESELECTOR
SETUP MICSD CARDTUNESELECTOR
SELECTORTUNE
Listening/confirming the preset 
channels
Manual tuning
ST
T MONO
T
MONO
After changing the setting, previously preset frequencies will be cleared. Preset them again.
NOTE
Radio
BT300.book  26 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							27
RQT9508
Enjoying TV, etc. with this unit’s speakers
You can enjoy TV broadcasts with this unit’s speakers.
PreparationConfirm the audio connection to the OPTICAL IN or AUX terminal on 
the main unit. (>10 to 12)
Turn on the TV.
1 Press [EXT-IN] several times to select “D-IN 1” 
(DIGITAL IN 1)*1, “D-IN 2” (DIGITAL IN 2)*2 or 
“AUX”*1.Main unit: Press [SELECTOR].
≥ D-IN 1 (DIGITAL IN 1) *
1:
When connecting using OPTICAL 1(TV) terminal.
≥ D-IN 2 (DIGITAL IN 2) *
2:
When connecting using OPTICAL 2(STB) terminal.
≥ AUX *
1:
When connecting using AUX terminal.
*1 For connections with the TV. ( >10, 11)
*2 For connections with other devices. ( >12)
≥ When the system is connected to an HDAVI Control 2 or 
later-compatible TV via an HDMI cable, TV broadcast audio is output 
through the system speakers if the TV input is switched to TV tuner 
mode. See “Setting the TV audio for VIERA Link “HDAVI Control”” on 
page 28 for setting method.
≥ Reduce the volume on the TV to its minimum, and then adjust the 
volume of the main unit.
You can enhance stereo sources with surround sound effect.
Press [SURROUND] several times to select the mode.≥ You can also press [SURROUND] and then [ 3,4 ] to select the 
mode.
≥ The selected effect will only be displayed on the main unit.
While “MANUAL” is displayed
Press [ 2,1] and select the desired effect.
For more detailed information on this operation, please refer to the 
“Enjoying surround sound effects” section on page 18. You can adjust the mode depending on the source or situation.
1
Press [SOUND] several times to select the mode.≥You can also press [SOUND] and then [ 3,4] to select the 
mode.
≥ The selected effect will only be displayed on the main unit.
2While the selected mode is displayed
Press [ 2,1] and select the desired setting.
For more detailed information on this operation, please refer to the 
“Changing the sound modes” section on page 18.
Select to suit the type of audio from the OPTICAL IN terminals on the 
main unit.
≥Underlined items are the factory presets.
1 Press [EXT-IN] several times to select “ D-IN 1” 
( DIGITAL IN 1 ) or “D-IN 2 ” (DIGITAL IN 2 ).
Main unit: Press [SELECTOR] .2Press [STATUS] several times to select the 
mode.
≥You can also press [STATUS] and then [ 3,4 ] to select the 
mode.
≥ The digital audio input settings are to be set separately to each 
source, “D-IN 1” and “D-IN 2”.
≥ The selected effect will only be displayed on the main unit.
3While the selected mode is displayed
Press [ 2,1] and select the desired setting.*3 When “D-IN 1” is selected.
*4 When “D-IN 2” is selected.
*5 The device connected to the OPTICAL 2(STB) terminal must be 
connected to the TV via an HDMI cable. If it is not connected via an 
HDMI cable, “NOT CONDITIONAL” is displayed on the main unit.
Enjoying TV and other devices sound 
from this unit’s speakers
Recommended modes to enjoy TV audio:
≥DOLBY PL II MOVIE
≥ DOLBY PL II MUSIC
≥ S.SURROUND
OK
EXT-IN
SOUNDSURROUND
STATUS
EXT-IN
STATUS
SURROUND SOUND
TUNESELECTOR
SETUP MICSD CARDSELECTOR
SELECTOR
Adjusting the sound
Making settings for digital audio input
Available settings
Mode Setting
DUAL: (Only works with Dolby Dual Mono)
–MAIN
– SAP*
– M+S
* (stereo audio)
*“ SAP” = Secondary Audio Program
DRC:
(Dynamic 
Range 
Compression) –
ON
Adjust for clarity even when the volume is low by 
compressing the range of the lowest sound level 
and the highest sound level. Convenient for late 
night viewing. (Only works with Dolby Digital)
– OFF
The full dynamic range of the signal is 
reproduced.
PCM FIX: –ON
Select when receiving only PCM signals.
– OFF
Select when receiving Dolby Digital and PCM 
signals.
≥ When receiving true 5.1-channel surround 
sound, select “OFF”.
TV AUDIO*
3: –
AUXSelect when receiving analog sound from the TV 
to the AUX terminal.
– D-IN 1
Select when receiving digital sound from the TV 
to the OPTICAL 1(TV) terminal.
CABLE/SAT 
AUDIO*
4, 5: –
SET
Select when setting the main unit to switch to 
“D-IN 2” when the input channel of an HDMI 
connected STB is selected on the TV ( B28, 
Setting the TV audio for VIERA Link “HDAVI 
Control”).
– OFF
Select to cancel this setting.
≥Audio that is input through the OPTICAL DIGITAL IN or 
AUX terminals are not output from the HDMI terminal.
NOTE
TV
BT300.book  27 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							28
RQT9508
Linked operations with the TV
(VIERA LinkTM “HDAVI ControlTM”)
When switching between this unit’s speakers and TV speakers, the TV screen may be blank for several seconds.
What is VIERA Link “HDAVI Control”?
VIERA LinkTM is a new name for EZ SyncTM.
VIERA Link “HDAVI Control” is a convenient function that offers linked 
operations of this unit, and a Panasonic TV (VIERA) under “HDAVI Control”.
You can use this function by connecting the equipment with an HDMI cable. See 
the operating instructions for connected equipment for operational details.
Preparation1 Connect this unit to your TV with an HDMI cable. ( >11 )
2 Set “VIERA Link” to “On”. ( >39) 
(The default setting is “On”.)
3 Set the “HDAVI Control” operations on the connected equipment (e.g., TV).
4Turn on all “HDAVI Control” compatible equipment and select this unit’s input 
channel on the connected TV so that the “HDAVI Control” function works 
properly.
Also when the connection or settings are changed, repeat this procedure.
≥VIERA Link “HDAVI Control”, based on the control 
functions provided by HDMI which is an industry 
standard known as HDMI CEC (Consumer 
Electronics Control), is a unique function that we 
have developed and added. As such, its operation 
with other manufacturers’ equipment that 
supports HDMI CEC cannot be guaranteed.
≥This unit supports “HDAVI Control 4” function.“HDAVI Control 4” is the newest standard 
(current as of December, 2008) for Panasonic’s 
HDAVI Control compatible equipment. This 
standard is compatible with Panasonic’s 
conventional HDAVI equipment.
≥ Please refer to individual manuals for other 
manufacturers’ equipment supporting VIERA 
Link function.
≥ It is recommended that you use 
Panasonic’s HDMI cable.
Recommended part number:
RP-CDHG10 (1.0 m/3.3 ft.), RP-CDHG15 (1.5 m/
4.9 ft.), RP-CDHG20 (2.0 m/6.6 ft.), RP-CDHG30 
(3.0 m/9.8 ft.), RP- CDHG50 (5.0 m/16.4 ft.), etc.
≥Non-HDMI-compliant cables cannot be utilized.
Setting the TV audio for VIERA Link “HDAVI Control”
You can set the main unit to link audio operations with the TV.∫Setting the audio from the TV
Preparation
≥Select between “AUX” and “D-IN 1” ( DIGITAL IN 1 ) to work with the linked 
operations for the TV audio. 
– Confirm the audio connection to the  AUX(TV) terminal (for “AUX”) or 
OPTICAL 1(TV) terminal (for “ D-IN 1 ”).  (> 11 )
With the remote control of the main unit;
1 Press [EXT-IN] to select “AUX” or “D-IN 1” (DIGITAL IN 1).
2 Press [STATUS].
3 Press [ 3,4] to select “TV AUDIO”.
4 Press [ 2,1] to switch “AUX” or “D-IN 1” (DIGITAL IN 1) and press [OK].
Whenever the connection or settings are changed, reconfirm the points above.
∫ Setting the audio from the STB
This unit can be set to link operations with the TV so as to output audio from the 
connected STB, etc. when the TV input is set to the input channel designated for 
the STB, etc.
Preparation
≥Select the STB input channel on the TV.
≥Confirm the audio connection to the OPTICAL 2(STB) terminal (for “D-IN 2”). (>12)
With the remote control of the main unit;
1 Press [EXT-IN] to select “D-IN 2” (DIGITAL IN 2).
2 Press [STATUS].
3 Press [ 3,4] to select “CABLE/SAT AUDIO”.
4 Press [ 2,1] to select “SET” and press [OK].
≥ If the input channel of the STB on the TV is changed or if you want to change 
the device allocated for the linked operations, select “OFF” in step  4 above and 
then repeat steps  1 to 4.
≥The connected STB must also be connected 
to the TV via an HDMI cable.
Refer to the operating instructions of the 
respective device for details.
≥It is also possible to connect an HDMI and 
optical output compatible Panasonic DVD 
recorder in the place of the STB.
What you can do with “HDAVI Control”
Speaker control
You can select whether audio is output from the unit’s speakers or the TV speakers by using the TV menu settings. For details,  refer to the 
operating instructions of your TV.
Home theater
This unit’s speakers are active.
≥ When this unit is in standby mode, changing the TV speakers to this unit’s speakers in the TV menu will automatically turn the  unit on and 
select “AUX”*
1, “D-IN 1” (DIGITAL IN 1)*1 or “D-IN 2” (DIGITAL IN 2)*2 as the source.
≥ The TV speakers are automatically muted.
≥ You can control the volume setting using the volume or mute button on the TV’s remote control. (The volume level is displayed o n the main 
unit’s FL display.)
≥ To cancel muting, you can also use the home theater remote control ( >19).
≥ If you turn off this unit, TV speakers will be automatically activated.
TV
TV speakers are active.
≥ The volume of this unit is set to “0”.
– This function works when “BD/DVD”, “SD”, “AUX”*
1, “D-IN 1” (DIGITAL IN 1)*1 or “D-IN 2” (DIGITAL IN 2)*2 is selected as the source on the 
home theater system.
≥ Audio output is 2-channel audio.
≥When “TV” is selected in “Speaker control”, the audio from an iPod will not be output from the TV’s speakers during slideshow 
background music playback. (>24)
NOTE
NOTE
TIPS
NOTE
TV
BT300.book  28 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							29
RQT9508
If you connect this unit to a TV that has “HDAVI Control 2” or later with 
an HDMI cable, you can operate this unit using buttons on the TV 
remote control.
The buttons that you can use for this unit vary, depending on the TV. 
For details, refer to the operating instructions of the TV.
Use the remote control supplied with this unit if you cannot operate this 
unit using buttons on the TV remote control.
≥The operation of this unit may be interrupted when you press 
incompatible buttons on the TV remote control.
∫ Using the Control Panel
You can operate the playback with the indicated 
controls.
∫ When you want to leave the TV on and set only this unit to standby modePress [ Í] on this unit’s remote control and set to standby mode.∫When not using “HDAVI Control”Set “VIERA Link” in the Setup menu to “Off”. ( >39)
Automatic input switching
When the following operations are performed, the TV will 
automatically switch the input channel and display the 
corresponding action.
– When play starts on the unit
– When an action that uses the display screen is performed
(e.g., Direct Navigator screen)
≥ When you switch the TV input to TV tuner mode, this unit will 
automatically switch to “AUX”*
1, “D-IN 1” ( DIGITAL IN 1 )*1 or “D-IN 
2” ( DIGITAL I N 2 )*2.
≥ This function does not work when the iPod selector (SIMPLE 
mode) or iPod Video menu (EXTENDED mode) is chosen. ( >31)
≥When [1 PLAY] is pressed, the playback image is not 
immediately displayed on the screen and it may not be 
possible to watch the contents from where playback 
started.
In this case, press [SKIP :] or [SEARCH 6] to go back 
to where playback started.
Automatic lip-sync function 
(for HDAVI Control 3 or later)
Delay between audio and video is automatically adjusted, enabling 
you to enjoy smooth audio for the picture. ( >39, Time Delay)
≥ This function works only when “BD/DVD”, “SD”, “AUX”*
1, “D-IN 1” 
(DIGITAL I N 1 )*1 or “D-IN 2” (DIGITAL I N 2 )*2 is selected as the 
source on this unit.
Power off link
All connected equipment compatible with “HDAVI Control”, including 
this unit, automatically turns off when you switch the TV off.
≥ This unit automatically turns off even during playback or any other 
operation.
To continue audio playback even when the TV is turned off, 
select “Video” in “Power Off Link”. ( >39)
∫ Auto power stand-by
Auto power stand-by responsibly manages your power 
consumption.
This function is available with a TV that supports “HDAVI Control 4”.
≥If connected with a TV (VIERA) with the “Auto power stand-by” 
setting activated on the TV, when switching the TV input, the unit 
will be automatically turned to standby. For details please read the 
operating instructions of the TV. 
– When “Speaker control” is set to “Home theater”, the main unit 
will not automatically turn to standby.
One touch play
You can turn on this unit and the TV, and start play with a single 
press of a button.
While the unit and the TV are in standby mode;
Press [ 1PLAY].
≥ This unit’s speakers will automatically be activated. ( >28)
≥When [1 PLAY] is pressed, the playback image is not 
immediately displayed on the screen and it may not be 
possible to watch the contents from where playback 
started.
In this case, press [SKIP :] or [SEARCH 6] to go back 
to where playback started.
*1“AUX” or “D-IN 1” works depending on the “TV AUDIO” setting. 
(B 28, Setting the TV audio for VIERA Link “HDAVI Control”)
*2“D-IN 2” works depending on the “ CABLE/SAT AUDIO” setting. 
(B 28, Setting the TV audio for VIERA Link “HDAVI Control”)
NOTE
NOTE
Easy control only with VIERA remote 
control
Using the START menu to operate this unit
By using the TV remote control, you can play media using the 
START menu.
1 Press the button for VIERA Link 
on the TV remote control.
2 Select the home theater.
≥The START menu is displayed
3 Select the desired items on the 
START menu ( >16).
Using the sub menu to operate this unit
By using the TV remote control, you can play discs using the 
“Control Panel” and display the Top Menu (for BD-Video and 
DVD-Video) or Pop-up Menu (for BD-Video).
≥This works only during “BD/DVD” or “SD” playback and resume modes.
1 Press [SUB MENU].≥You cannot use the sub menu while the Top 
Menu for BD-Video or DVD-Video is displayed.
≥This can also be displayed by using the 
VIERA menu screen.
2 Select an item, then press [OK].
Control PanelControl Panel is displayed. Follow the 
indications on the screen. (>belo w)
Screen Aspect(> 21)
Top Menu  [BD-V] [AVCHD]  [DVD-V]Top menu is displayed.
Menu  [DVD-V]Menu is displayed.
Pop-up Menu  [BD-V]Pop-up menu is displayed.
Rotate Right [JPEG]Rotate the still picture.
Ro tate L eft [JPEG]
Zoom in [JPEG]Enlarge or shrink the still picture.
Zoom out  [JPEG]
≥Depending on the menu, some button operations cannot 
be performed from the TV’s remote control.
≥ You cannot input numbers with the numbered buttons on 
the TV’s remote control ([0] to [9]). Use this unit’s remote 
control to select the playlist etc.
e.g.,  [BD-V]
Menu
OKRETURN
Other Functions
Playback DISCTo p  M e n u
Home theater START
BD-Video
Input SelectSound(Equalizer)
Network
OK
RETURN
SUB
MENU
Control Panel
Screen Aspect
Top Menu
Pop-up Menu
e.g.,  [BD-V]
e.g.
NOTE
TV
BT300.book  29 ページ  ２００９年６月１２日　金曜日　午後１２時１３分 
						

							30
RQT9508
Using the iPod
You can enjoy iPod music through this unit’s speakers or view iPod videos/photos on the TV.
Preparation≥To view photos/videos from the iPod.
– Ensure the video connection to the VIDEO OUT terminal on this unit  (> 10).
– Operate the iPod menu to make the appropriate video/photo output settings for your TV. (Refer to the operating instructions of  your iPod.)
≥ To display the picture, turn on the TV and select the appropriate video input mode.
≥ Before connecting/disconnecting the iPod, turn the main unit off or reduce the volume of the main unit to its minimum.
While an iPod is connected
≥ Do not push the Dock for iPod. ≥Do not push or pull your iPod back and forth with great force.
Compatible iPod
iPod Connection
1 Open the Dock for iPod.
≥Hold the dock when connecting/disconnecting the iPod.
About dock adapter≥Attach the dock adapter which should be 
supplied with your iPod to the dock for the 
stable use of the iPod. If you need an adapter, 
consult your iPod dealer.
About recharging the battery≥iPod will start recharging regardless of whether 
this unit is on or off.
≥ “IPOD  ¢” will be shown on the main unit’s 
display during iPod charging in main unit 
standby mode.
≥ Check iPod to see if the battery is fully 
recharged.
≥ If you are not using iPod for an extended period 
of time after recharging has completed, 
disconnect it from main unit, as the battery will 
be depleted naturally. (Once fully recharged, 
additional recharging will not occur.)
2 Connect the iPod (not included) firmly.Recharging starts when the iPod is inserted.
Main unit
iPod
Pull out
Main unit Dock for iPodDock adapter 
(not included)
NOTE
DO NOTDO NOT
NameMemory size≥
Compatibility depends on the software version 
of your iPod.
≥ Audio/video cannot be recorded or transmitted 
to the iPod via this system.
≥ Panasonic makes no warranty for iPod data 
management.
≥ For more information, refer to the operating 
instructions for iPod.
≥ The contents of the operating instructions and 
those displayed on iPod may differ partially, but 
this will not fundamentally affect use of 
playback.
∫ To use the iPod touch features
1 Press the Home button on the iPod touch.
2 Select the iPod touch features on the touch 
screen to operate.
iPod touch 2nd generation
8 GB, 16 GB, 32 GB
iPod nano 4th generation (video) 8 GB, 16 GB
iPod classic 120 GB
iPod touch 1st generation 8 GB, 16 GB, 32 GB
iPod nano 3rd generation (video) 4 GB, 8 GB
iPod classic 80 GB, 160 GB
iPod nano 2nd generation (aluminum) 2 GB, 4 GB, 8 GB
iPod 5th generation (video) 60 GB, 80 GB
iPod 5th generation (video) 30 GB
iPod nano 1st generation 1 GB, 2 GB, 4 GB
iPod 4th generation (color display) 40 GB, 60 GB
iPod 4th generation (color display) 20 GB, 30 GB
iPod 4th generation 40 GB
iPod 4th generation 20 GB
iPod mini4 GB, 6 GB
NOTE
Other devices
BT300.book  30 ページ  ２００９年６月１２日　金曜日　午後１２時１３分