Panasonic Aj Ufc1800 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj Ufc1800 Operating Instructions Manual. The Panasonic manuals for Software are available online for free. You can easily download all the documents as PDF.
Page 21
21 Diagnostics Menu The DIAGNOSTICS menu is activated by pushing the DIAG button on the UFC front panel. This menu shows any errors or warnings that have been detected by the system. Three submenus are available from the top menu: ALL, MONITORED & TRIGGERED. DIAG DIAG MONIT‘D ERRORS: 29 ALL ↓MON‘D ↓TRIG‘D ↓RET RIG MON/MASK F1 F2 F3 F4 F5 EXIT F1 – Opens up the ALL submenu to show all possible error messages. F2 – Opens up the MONITORED submenu to show which error conditions are being monitored. F3 –...
Page 22
22 Audio Menus The AUDIO menus are activated by pushing the AUDIO button on the UFC front panel. These menus allow the user to change audio routing and delay in the system, as well as enable or disable the audio synchronizers (sample rate converters). Each block of 4 outputs can have their input source selected independently, and also have their synchronizers enabled or disabled. The serial digital input may contain 4/8 channels of embedded audio, and the serial digital output of the system may also...
Page 23
23 Test Menus The TEST menu is activated by pushing the TEST button on the UFC front panel. This menu allows the user to activate the internal test pattern generator, select patterns, or activate the frame store feature. SIGNAL GEN TEST > SIG GEN SELECT F STORE F1 F2 F3 F4 F5 EXIT F1 – Activates knob to select the test pattern (Off, Stored Frame and various H/V based patterns). F2 – Captures current video image to frame store. This is only active when SELECT is set to “OFF”. Setup Menus The SETUP menus...
Page 24
24 TIME CODE-INPUT This menu allows the user to select the source for LTC and indicate drop frame or non-drop frame TC. SETUP > TIME CO DE-INPUT SOURCE DF MODE F1 F2 F3 F4 F5 EXIT F1 – Selects whether the time code source is from the serial input or from the external TC connector (S_LTC, EXT_LTC or S_VITC). F2 – When this is on AUTO, the time code source drop frame flag is used. Otherwise, non-drop frame mode is set (AUTO, OFF). Note: When an SD input is selected, S_LTC cannot be selected. TIME...
Page 25
25 LOCK This menu allows the user to set a system password by using the menu keys. SETUP >> LOCK PASSWD PRESETS CONTROLS F1 F2 F3 F4 F5 EXIT F1 – Allows the system password to be set. F2 – Locks or unlocks user presets 1-8. F3 – Locks or unlocks the control panel and remote ports. SET PASSWORD If a password already exists, then it must be entered to set a new password. To clear an existing password, hold down the F2 and F3 keys for at least 3 seconds. A sequence of four menu keys must be entered. SETUP...
Page 26
26 Error messages No. Message Error description Remedy DIO- 1NO SD DIG VIDEO INPUT No signal is detected on the SD serial input.Check SD input signal. DIO- 2NO HD DIG VIDEO INPUT No signal is detected on the HD serial input.Check HD input signal. DIO- 3HD SDI CRC ERROR A checksum error was found on the HD serial input.Check HD SDI input cable and/or source. DIO- 4NO SD EMBEDDED AUDIO INPUTNo embedded audio signal is detected on the SD serial input.This may not be supported by the source equipment. DIO-...
Page 27
27 AUD -6CH 5/6 AUDIO CRC ERROR A checksum error was found on the external audio signal.Check cable and/or source. AUD -7CH 7/8 AUDIO PARITY ERRORA parity error was found on the external audio signal.Check cable and/or source. AUD -8CH 7/8 AUDIO CRC ERROR A checksum error was found on the external audio signal.Check cable and/or source. SYS -1FAN STOPPED The rear panel cooling fan has stopped.Check for obstruction. MM- 1NO EXT SYNC Reference is external sync, but no signal is detected.Check EXT SYNC...
Page 28
28 Remote connectors The RS-232 serial port supports downloads of new system software and limited remote control operation. The GPI port allows remote selection of PRESETS 1-8 when the front panel REMOTE/LOCAL switch is in the “REMOTE” position. The GPI inputs are active low so that a connection between pins 1-8 and pin 9 will select the corresponding PRESET. RS-232 pins: 1 – NC GPI pins: 1 – preset 1 2 – receive 2 – preset 2 3 – transmit 3 – preset 3 4 – NC 4 – preset 4 5 – GND 5 – preset 5 6 –...
Page 29
30/29 Frame Time Code NDF DF ConversionNDFDFdifference 00:00:00:0024:01:22:26 00:00:03:1724:01:26:13 00:00:03:1800:00:00:00-00:00:03:18 00:59:00:0000:58:59:28-00:00:00:02 00:59:00:0100:58:59:29-00:00:00:02 00:59:00:0200:59:00:02 00:00:00:00 SYNC POINT01:00:00:0001:00:00:00 00:00:00:00 01:00:59:2901:00:59:29 00:00:00:00 01:01:00:0001:01:00:02+00:00:00:021min. = 2Frame 01:01:59:2701:01:59:29 01:01:59:2801:02:00:02+00:00:00:04 01:01:59:2901:02:00:03 01:02:00:0001:02:00:04 01:02:59:2501:02:59:29...
Page 30
30/29 Frame Time Code NDF DF Conversion NDFDFdifference01:08:59:1301:08:59:29 01:08:59:1401:09:00:02+00:00:00:18 01:09:00:0001:09:00:18 01:09:59:1101:09:59:29 01:09:59:1201:10:00:00+00:00:00:1810min. = 18Frame 01:09:59:2901:10:00:17 01:10:00:0001:10:00:18 01:10:00:0101:10:00:1901:19:58:2401:20:00:00+00:00:01:06 01:29:58:0601:30:00:00+00:00:01:24 01:39:57:1801:40:00:00+00:00:02:12 01:49:57:0001:50:00:00+00:00:03:00 01:59:56:1202:00:00:00+00:00:03:181Hr. = 3sec.18F...