Panasonic Aj Sd965 Operating Instructions Manual
Have a look at the manual Panasonic Aj Sd965 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 76
76
The VTR can be operated by commands when the RS-
232C interface is used.
(See command table on pages 79, 80.)
$Conditions for acknowledging
commands from RS-232C interface
O The REMOTE button on the front panel must be
set to the remote mode (REMOTE lamp ON).
O The setup menu No. 204 “ RS232C SEL” must be
ON.
If the above conditions are not met, [ACK] + [STX]
ER001 [EXT] is returned to the external unit.
Whether the [ACK] code is returned depends on the
setting which has been selected for setup menu...](http://img.usermanuals.tech/thumb/58/67799/w64_aj-sd965_en_om_d-75.png "Page 76
76
The VTR can be operated by commands when the RS-
232C interface is used.
(See command table on pages 79, 80.)
$Conditions for acknowledging
commands from RS-232C interface
O The REMOTE button on the front panel must be
set to the remote mode (REMOTE lamp ON).
O The setup menu No. 204 “ RS232C SEL” must be
ON.
If the above conditions are not met, [ACK] + [STX]
ER001 [EXT] is returned to the external unit.
Whether the [ACK] code is returned depends on the
setting which has been selected for setup menu...")
![Page 78
78
RS-232C interface(continued)
3. Return format [VTR 5 controller (PC)]
The following responses are made to the command. If
necessary, more than one response is made.
$When the communication has terminated
normally
1. The receive completion message is returned.
[ACK]06h
2. The execution completion message is returned. [STX] [command] [data] [ETX]
02h XX XX XX XX .....
XX 03h
[command] :
This is the message (data) which is returned or
the execution completion message identifier.
[data] : This is the data...](http://img.usermanuals.tech/thumb/58/67799/w64_aj-sd965_en_om_d-77.png "Page 78
78
RS-232C interface(continued)
3. Return format [VTR 5 controller (PC)]
The following responses are made to the command. If
necessary, more than one response is made.
$When the communication has terminated
normally
1. The receive completion message is returned.
[ACK]06h
2. The execution completion message is returned. [STX] [command] [data] [ETX]
02h XX XX XX XX .....
XX 03h
[command] :
This is the message (data) which is returned or
the execution completion message identifier.
[data] : This is the data...")
![Page 79
79
RS-232C interface(continued)
5. Command table
$ Commands relating to operation control
O As for the return (completion) message, [ACK] is
first returned when data is received, and the
execution message is subsequently returned. It is
only the execution message which is listed in this
table.
O In the case of commands not listed in the table,
ER001 (invalid command) is returned after [ACK]
has been returned.
VTR
operation Send command
STOP[STX] OSP [ETX]
45[STX] OSP [ETX]
This command is for stopping...](http://img.usermanuals.tech/thumb/58/67799/w64_aj-sd965_en_om_d-78.png "Page 79
79
RS-232C interface(continued)
5. Command table
$ Commands relating to operation control
O As for the return (completion) message, [ACK] is
first returned when data is received, and the
execution message is subsequently returned. It is
only the execution message which is listed in this
table.
O In the case of commands not listed in the table,
ER001 (invalid command) is returned after [ACK]
has been returned.
VTR
operation Send command
STOP[STX] OSP [ETX]
45[STX] OSP [ETX]
This command is for stopping...")
![Page 80
80
RS-232C interface(continued)
$Commands relating to inquiries
O As for the return (completion) message, [ACK] is
first returned when data is received, and the
execution message is subsequently returned. It is
only the execution message which is listed in this
table.
O In the case of commands not listed in the table,
ER001 (invalid command) is returned after [ACK]
has been returned.
VTR
operation Send command
CTL/TC DATA
REQUEST[STX] QCD [ETX]
45[STX] CD data [ETX]
This command is for inquiring about...](http://img.usermanuals.tech/thumb/58/67799/w64_aj-sd965_en_om_d-79.png "Page 80
80
RS-232C interface(continued)
$Commands relating to inquiries
O As for the return (completion) message, [ACK] is
first returned when data is received, and the
execution message is subsequently returned. It is
only the execution message which is listed in this
table.
O In the case of commands not listed in the table,
ER001 (invalid command) is returned after [ACK]
has been returned.
VTR
operation Send command
CTL/TC DATA
REQUEST[STX] QCD [ETX]
45[STX] CD data [ETX]
This command is for inquiring about...")
![Page 83
83
[GENERAL]
indicates safety information.
Power supply:
AC 100 – 240 V, 50/60 Hz
Power consumption: 115 W
130 W (with all options)
Operating ambient temperature:
5°C to 40°C
Operating ambient humidity: 10% to 80% (no condensation)
Weight: 38.5 lb (17.5 kg)
Dimensions (WaHaD): 16
3/4inchesa6 15/16inchesa16 7/16inches
(424 mma175.2 mma417 mm)
(Not including the support legs, connectors, and JOG dial)
Recording format: DVCPRO50/DVCPRO format selectable
Recording video signal: 525i/625i system selectable...](http://img.usermanuals.tech/thumb/58/67799/w64_aj-sd965_en_om_d-82.png "Page 83
83
[GENERAL]
indicates safety information.
Power supply:
AC 100 – 240 V, 50/60 Hz
Power consumption: 115 W
130 W (with all options)
Operating ambient temperature:
5°C to 40°C
Operating ambient humidity: 10% to 80% (no condensation)
Weight: 38.5 lb (17.5 kg)
Dimensions (WaHaD): 16
3/4inchesa6 15/16inchesa16 7/16inches
(424 mma175.2 mma417 mm)
(Not including the support legs, connectors, and JOG dial)
Recording format: DVCPRO50/DVCPRO format selectable
Recording video signal: 525i/625i system selectable...")
![Page 84
84
Specifications(continued)
[VIDEO]
$Video output connector
Analog component output:
BNCa3 (Y, PB, PR)
Y: 1.0 V [p-p], PB/PR: 0.486/0.7 V [p-p] switchable,
(75% color bar, 7.5% setup)
Analog composite output: BNCa 3, video 1, video 2 (video/WFM selectable), video 3
(superimpose on/off)
SDI output: BNCa3, SDI 1, SDI 2, SDI 3 (superimpose on/off),
complies with SMPTE259M-C/ITU-R BT.656-4 standard
$Video signal adjustment
Video output gain:
±3 dB
Video output chroma gain: ±3 dB
Video output HUE (chroma...](http://img.usermanuals.tech/thumb/58/67799/w64_aj-sd965_en_om_d-83.png "Page 84
84
Specifications(continued)
[VIDEO]
$Video output connector
Analog component output:
BNCa3 (Y, PB, PR)
Y: 1.0 V [p-p], PB/PR: 0.486/0.7 V [p-p] switchable,
(75% color bar, 7.5% setup)
Analog composite output: BNCa 3, video 1, video 2 (video/WFM selectable), video 3
(superimpose on/off)
SDI output: BNCa3, SDI 1, SDI 2, SDI 3 (superimpose on/off),
complies with SMPTE259M-C/ITU-R BT.656-4 standard
$Video signal adjustment
Video output gain:
±3 dB
Video output chroma gain: ±3 dB
Video output HUE (chroma...")
![Page 86
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835\
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500...](http://img.usermanuals.tech/thumb/58/67799/w64_aj-sd965_en_om_d-85.png "Page 86
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835\
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500...")
81 Connector signals VIDEO IN SDI IN (DIGITAL)BNCa2, Active through Y, PB, PR (ANALOG)BNCa3 (Board, option) VIDEO INBNCa2, Loop-through, 75Ω termination switch provided (Board, option) REF VIDEO IN BNCa2, Loop-through, 75Ωtermination switch provided AUDIO IN SDI IN (DIGITAL) BNCa2, Active through AUDIO IN (DIGITAL)BNCa2 (CH1/CH2, CH3/CH4) AES/EBU format AUDIO IN (ANALOG)XLRa4 (CH1, CH2, CH3, CH4) TIME CODE IN XLRa1 AUDIO OUT SDI OUT (DIGITAL)BNCa3 AUDIO OUT (DIGITAL)BNCa2 (CH1/CH2, CH3/CH4) AES/EBU format AUDIO OUT (ANALOG)XLRa4 (CH1, CH2, CH3, CH4) TIME CODE OUTXLRa1 MONITOR OUTXLRa2 (L/R) HEADPHONES(front)Stereo mini jack RS-422A REMOTE (9P) O REMOTE IN/OUT VIDEO OUT SDI OUT (DIGITAL) BNCa3 Y, PB, PR (ANALOG)BNCa3 VIDEO OUT BNCa3 Pin No. Signal 1FRAME GROUND 2TRANSMIT A 3RECEIVE B 4RECEIVE COMMON 5 ==== 6TRANSMIT COMMON 7TRANSMIT B 8RECEIVE A 9FRAME GROUND OREMOTE OUT Pin No. Signal 1FRAME GROUND 2RECEIVE A 3TRANSMIT B 4TRANSMIT COMMON 5 ==== 6RECEIVE COMMON 7RECEIVE B 8TRANSMIT A 9FRAME GROUND
82 Connector signals(continued) PARALLEL REMOTE (25P) Pin No. Signal 1PLAY COMMAND 2STOP COMMAND 3FF COMMAND 4REW COMMAND 5REC COMMAND 6EJECT COMMAND 7STAND BY COMMAND 8PREROLL COMMAND 9IN SET COMMAND 10 ==== 11==== 12 610 V, MAX 300 mA 13PLAY STATUS 14STOP STATUS 15FF STATUS 16REW STATUS 17REC STATUS 18EJECT STATUS 19STAND BY ON STATUS 20PREROLL STATUS 21SERVO LOCK STATUS 22OPERATION ENABLE STATUS 23 ==== 24==== 25GND OCOMMAND pins: TTL level, active low, 6 100ms edge electrical signal. O STATUS pins: open collector, sink current 6 mA ENCODER (15P) Pin No. Signal 1 ==== 2SET UP/BLACK LEVEL 3C LEVEL 4GND 5+9 V 6SYSTEM H PHASE 7SYS. SC COARSE (2) 8–9 V 9HUE/CHROMA PHASE 10 VIDEO LEVEL 11RET GND 12 ==== 13==== 14SYS. SC FINE 15 SYS. SC COARSE (1) RS-232C D-SUB 25-pin (crossover cable supported) Pin No. Signal Description 1FG Protective ground (Frame ground) 2 RXD Received data (Data is sent to PC.) 3 TXD Transmitted data (Data is received from PC.) 4 CTS Clear to send (Shorted with pin 5.) 5 RTS Request to send (Shorted with pin 4.) 6 DTR Data terminal ready (No processing) 7 SG Signal ground (Signal ground) 20 DSR Data set ready (+ voltage output after communication enable status)
83 [GENERAL] indicates safety information. Power supply: AC 100 – 240 V, 50/60 Hz Power consumption: 115 W 130 W (with all options) Operating ambient temperature: 5°C to 40°C Operating ambient humidity: 10% to 80% (no condensation) Weight: 38.5 lb (17.5 kg) Dimensions (WaHaD): 16 3/4inchesa6 15/16inchesa16 7/16inches (424 mma175.2 mma417 mm) (Not including the support legs, connectors, and JOG dial) Recording format: DVCPRO50/DVCPRO format selectable Recording video signal: 525i/625i system selectable Recording audio signal: DVCPRO50:48 kHz 16-bit 4 channels DVCPRO: 48 kHz 16-bit 2 channels Recording tracks: Digital video audio:helical track The time code is recorded in the sub-code area. Cue track: 1 track Control track: 1 track Tape speed: [525i system]67.640 mm/sec (DVCPRO50) [625i system] 67.708 mm/sec (DVCPRO50) Recording time: 50 Mbps:126 minutes (using the AJ-5P126XG) 92 minutes (using the AJ-5P92LP) 33 minutes (using the AJ-P66MP) 25 Mbps: 252 minutes (using the AJ-5P126XG) 184 minutes (using the AJ-5P92LP) 66 minutes (using the AJ-P66MP) Tape: Metal tape FF/REW time: Less than 3 min (with AJ-5P126XG) Less than 2 min (with AJ-P126LP) Less than 1 min (with AJ-P66MP) Digital slow: –0.43a to +0.43a, +0.5a, +0.75a speed (DVCPRO, DVCPRO50) Editing accuracy: ±0 frames (using the time code) Tape timer accuracy: ±1 frame (using the continuous CTL signal) Servo lock time: Less than 0.5 sec (color framing/standby ON) Specifications [VIDEO] $Digital video Sampling frequencies: Y: 13.5 MHz, PB/PR: 6.75 MHz (DVCPRO50) Quantizing: 8 bits Video compression method: DV-Based compression (SMPTE 314M) Video compression rate: DVCPRO50: 1/3.3, DVCPRO: 1/5 Error correction: Reed-Solomon product code Bit rate: DVCPRO50: 50 Mbps, DVCPRO: 25 Mbps $Digital IN/Analog component OUT Video bandwidth: [525i system]Y : 30 Hz to 5.75 MHz (±0.5 dB) P B/PR: 30 Hz to 2.75 MHz (±0.5 dB) [625i system] Y : 25 Hz to 5.75 MHz (±1.0 dB) P B/PR: 25 Hz to 2.75 MHz (±1.0 dB) S/N ratio: Better than 60 dB (Y) K factor: Less than 1% (Y 2T) Y/P B, PRdelay: Less than 10 ns $ Video input connector Analog component input (option): BNCa3 (Y, PB, PR) Y: 1.0 V [p-p], PB/PR: 0.486/0.7 V [p-p] switchable, 75Ω (75% color bar, 7.5% setup) Analog composite input (option): BNCa2, loop-through, 75Ω on/off Reference input: BNCa2, loop-through, 75Ω on/off SDI input: BNCa 2, active through, complies with SMPTE259M-C/ITU-R BT.656-4 standard
84 Specifications(continued) [VIDEO] $Video output connector Analog component output: BNCa3 (Y, PB, PR) Y: 1.0 V [p-p], PB/PR: 0.486/0.7 V [p-p] switchable, (75% color bar, 7.5% setup) Analog composite output: BNCa 3, video 1, video 2 (video/WFM selectable), video 3 (superimpose on/off) SDI output: BNCa3, SDI 1, SDI 2, SDI 3 (superimpose on/off), complies with SMPTE259M-C/ITU-R BT.656-4 standard $Video signal adjustment Video output gain: ±3 dB Video output chroma gain: ±3 dB Video output HUE (chroma phase): ±30° Video output setup (black) level: ±100 mV (±14 IRE) Video output sync phase: ±15 µsec Video output SC phase: More than ±180 ° [AUDIO] $Audio input connector Analog input (CH1, CH2, CH3, CH4): XLRa 4, 600Ω /high impedance selectable (factory setting: high impedance), +4/0/–20 dBu selectable Digital input (CH1/CH2, CH3/CH4): BNCa2, AES/EBU format SDI input: BNCa 2, active through, complies with SMPTE272M-A/ITU-R BT.656-4 standard $ Audio output connector Analog output (CH1, CH2, CH3, CH4): XLRa4, low impedance, +4/0/–20 dBu selectable Digital output (CH1/CH2, CH3/CH4): BNCa2, AES/EBU format, 75Ω, 1.0 ± 0.2 V [p-p] SDI output: BNCa 3, 75Ω , complies with SMPTE272M-A/ITU-R BT.656-4 standard Monitor output: XLRa2, low impedance, +4/0/–20 dBu selectable Headphones: Stereo mini jack, 8Ω, variable level [Other Input/Output Connectors] Time code input:XLRa1, 0.5 V to 8.0 V [p-p], 10 k Ω Time code output: XLRa1, low impedance, 2.0 V ± 0.5 V [p-p] RS-422A input: D-sub 9-pin, RS-422A interface RS-422A output: D-sub 9-pin, RS-422A interface RS-232C: D-sub 25-pin, RS-232C interface Parallel input/output: D-sub 25-pin Encoder remote: D-sub 15-pin [AUDIO] $Digital audio Sampling frequencies: 48 kHz (synchronous with video) Quantizing: 16 bits Frequency response: 20 Hz to 20 kHz ±1.0 dB (at the reference level) Dynamic range: Better than 90 dB (1 kHz, emphasis OFF, “A” weighted) Distortion: Less than 0.05% (1 kHz, emphasis OFF, reference level) Crosstalk: Less than –80 dB (1 kHz, between 2 channels) Wow & flutter: Below measurable limit Headroom: 20 dB De-emphasis: T1 = 50 µsec, T2 = 15 µsec (auto on/off) $Cue track Frequency response: 300 Hz to 6 kHz ±3.0 dB (DVCPRO50) Weight and dimensions when shown are approxlmately. Speclilcailons are subject to change without notice.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835\ Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 WESTERN ZONE: 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500 Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840 Broadcast PARTS INFORMATION & ORDERING: 9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880 Emergency after hour parts orders (800) 334-4881 TECHNICAL SUPPORT: Emergency 24 Hour Service (800) 222-0741 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010 Panasonic de Mexico S.A. de C.V. Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 \ 2127 Panasonic Sales Company Division of Matsushita Electric of Puerto Rico Inc. San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puer\ to Rico 00630 (787) 750-4300 © 2004 Matsushita Electric Industrial Co., Ltd. All rights reserved. P