Panasonic Aj Sd930be Operating Instructions Manual

Front panel
USET button
When this button is pressed, the data which has been
set using the setup menus is entered.
After the data has been entered, the setup menu
settings are exited, and the original status is restored.
When the internal time code has been set, the data
which has been set is entered.
VDIAG button
When this button is pressed, the VTR information is
displayed.
When it is pressed again, the original display is
restored.
The VTR information consists of the “WARNING”
information, “HOURS...

12 (E)
CONTENTS
Display panel
1TV system displays
The selected TV system is displayed here.
With the AJ-SD955B, it is possible to switch
between the 525 interlace and 625 interlace
systems by setting setup menu item No. 070 (TV
SYSTEM).
With the AJ-SD930B, only the 625 interlace TV
system can be used.
:This lights when the 625 interlaced TV system
is selected.
:This lights when the 525 interlaced TV system
has been selected. 
2WIDE lamp
This lamp lights when 16:9 wide-screen information
is being recorded...

13 (E)
CONTENTS
:EDIT, EDIT REC, REC and REC INH lamps
EDIT:
This lights when an editing mode has been
selected.
EDIT REC:
This lights when the edit recording mode has
been established.
REC:
This lights when the recording mode has been
established.
REC INH:
This lights in the recording inhibit status (when
the REC INH switch at the bottom front panel is
set to ON or the cassette is in the accidental
erasure prevention status).
In this status, recording and editing are not
possible.
Whether the REC INH...

14 (E)
CONTENTS
Rear panel
1AC IN socket
Connect one end of the power cord supplied to this
socket and the other end to the power outlet.
2DIGITAL AUDIO IN and OUT connectors
These are the input and output connectors for
digital audio signals that comply with the AES/EBU
standards.

The digital audio signals which are to be input to
these connectors must be synchronized with the
video input signals. Otherwise, noise will be
generated in the audio output signals.
3ANALOG COMPONENT VIDEO IN connectors...

15 (E)
CONTENTS
Rear panel
ANALOG COMPONENT VIDEO OUT connectors
The analogue component video signals are output
through these connectors.
?ANALOG COMPOSITE VIDEO OUT connectors
The analogue composite video signals are output
through these connectors.
The waveform monitor (WFM) signal can be output
from the VIDEO OUT 2 connector.
It can be selected using setup menu No. 00 (WFM
SEL).
Video signals containing superimposed information
can be output through the VIDEO OUT 3 connector.
Whether the...

16 (E)
CONTENTS
Source machine:
Set the CONTROL switch on the front panel to REMOTE.
Recorder:
Set the CONTROL switch on the front panel to LOCAL.
Connections
PUSH PUSH
PUSH PUSHPUSHAC IN
SIGNAL
GND
AES/EBUSDI
SDTI
ANALOGCH1/2
IN
YVIDEO
VIDEO
OUT
SERVICE ONLY
REMOTE IN/OUTCH1 CH2AUDIO
IN
ENCODER REMOTE
RS-232C
PARALLEL
REMOTE OUT
IN
REF VIDEOIN
ON
OFF
P
B
P
R
Y1
2
(WFM)
3(SUPER)
P
B
P
R
OPTION
CH3/4
IN
CH1/2
OUT
CH3/4
OUT
REMOTE
75Ω
ON
OFF75Ω
ANALOGTCININ
ACTIVE
THROUGH
OUT1TCOUT
MON
L
MON
R
CH4CH3
CH1...

17 (E)
CONTENTS
Connections with editing controller
Connections
ON
OFFPOWERDVDVCPRODVCPRO 50
METER
L
R FULL/FINEMONITOR SELECT
HEADPHONESMONITOR
MIXA VOL
SELECTINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOREC LEVELCH1PB LEVEL
AUDI OCH2 CH3 CH4TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON
OFFUNITY
VA R
COUNTERRESET
A  INTRIM
SETOUT INA  OUTCH1 CH4CH2INSERTCH3ASSEMVIDEO CUE TCSTAND BYEDIT
REW STOPPLAY REC PLAYERRECORDER
FF
JOGSHTLSLOW
TA P E
EEONREGENPRESETEXITOFFREMOTELOCAL
ON...

ON
OFFPOWERDVDVCPRODVCPRO 50
METER
L
R FULL/FINE
MONITOR SELECT
HEADPHONESMONITOR
MIXA VOL
SELECTINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEO
REC LEVELCH1PB LEVEL
AUDIOCH2 CH3 CH4TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON
OFFUNITY
VA R
COUNTERRESET
A  IN
TRIM
SET
OUT IN
A  OUTCH1 CH4CH2INSERTCH3ASSEMVIDEO CUE TCSTAND BY
EDIT
REW STOPPLAY REC PLAYER
RECORDER
FF
JOGSHTLSLOW
TAPE
EEONREGENPRESETEXITOFFREMOTELOCAL
L cassette size
18 (E)
CONTENTS
Consumer-use DV and DVCAM cassettes
(Standard...

19 (E)
CONTENTS
Jog mode
Jog/Shuttle
1Press the search dial so that it remains pressed in.
Check that the JOG lamp has lit.
Shuttle mode
1Press the search dial so that it is released from the
pressed-in position.
The SHTL lamp lights, and the shuttle mode is
established.
OImmediately after the power is turned on, turn
the search dial and leave it at the centre
position.
3To transfer the VTR from the jog mode to another
mode, press the button that corresponds to the
mode concerned.
2Turn the search dial....

20 (E)
CONTENTS
Manual editingSD955B
1Select the editing mode. 
ASSEMBLE:
Assemble (frame-to-frame continuity) editing is
performed in this mode.
INSERT: Insert editing is performed in this mode.
2Select the channels to be edited.
For insert editing, press the buttons corresponding
to the channels to be edited so that their lamps
light.
3Press the PLAY button.
4While monitoring the TV monitor, search the
position (IN point) where the editing is to be
started, and press the PLAY and EDIT buttons
together...