Panasonic Aj Sd930 Operating Instructions Manual

21
Automatic editing (deck-to-deck) SD955A
1Select the editing mode.
For assemble editing, press the ASSEM button.
For insert editing, press the INSERT button.
ASSEM:
This sets the unit to assemble (frame-to-frame
continuity) editing mode.
INSERT:
This sets the unit to insert editing mode.
2Select the channels to be edited.
With assemble editing, the ASSEM lamp lights.
With insert editing, press the buttons
corresponding to the channels to be edited so that
their lamps light.
3Select the VTR to be...

22
Automatic editing (deck-to-deck) SD955A
1Press the IN (or OUT) button to check the edit
point. The value of the registered edit point
appears on the display panel.
2While holding down the IN (or OUT) button, press
the PREROLL button and check the picture at the
edit point.
The tape is cued up to the edit IN (or OUT) point,
and a still picture of the point appears.
OIf STOP has been selected as the setup menu
No. 315 (AFTER CUE-UP) setting or if the
MODE switch has been set to EE, the VTR is
set to the...

23
Automatic editing (deck-to-deck) SD955A
1Re-registering an edit point
Locate the new edit point by performing the jog or
shuttle operation, and press the IN (or OUT) button
and SET button at the same time to re-register the
edit point.
2Modifying an edit point in 1-frame increments
(trimming function)
Press the TRIM button while holding down the IN
(or OUT) button. Each time the + button is
pressed, the point is moved ahead by one frame.
Conversely, each time the – button is pressed, the
point is...

24
2Upon completion of the editing, press the REVIEW
button.
Review is then started by the recorder side.
OTo stop the review at any time, press the STOP
button.
OWhen the edit OUT point is reached, the tape is
post-rolled, after which it stops.1Press the AUTO EDIT button.
Automatic editing is now executed.
OTo suspend editing at any time, press the STOP
button.
OWhen the edit OUT point is reached, the tape is
post-rolled, after which it stops.
Post-rolling
With assemble editing, editing continues for...

25
$Displaying the audio split edit points
The edit points appear on the display panel.
Video IN point:
Press the IN button.
Video OUT point:
Press the OUT button.
Audio IN point:
Press the A IN button.
Audio OUT point:
Press the A OUT button.

If the editing mode is changed to assemble editing
after the audio edit points have been registered, the
audio edit points will be cleared.
$Cueing the tape up to the edit points
Cue-up to video IN point:
Press the PREROLL button while holding down
the IN button....

26
Audio split editingSD955A
$Duration display
The duration can be indicated on the display panel
only.
Between the video IN and OUT points:
Press the IN button and OUT button at the same
time.
Between the audio IN and OUT points:
Press the A IN button and A OUT button at the
same time.
Match frame processing system
When two VTRs are used to perform the audio split
editing operations, there will be a total of 8 edit
points: the video IN and OUT points for the player,
the video IN and OUT points for the...

27
ON
OFFPOWERDVDVCPRODVCPRO 50
METER
L
R FULL/FINE
MONITOR SELECT
HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAU TO  EDITPREROLLVIDEO
REC LEVELCH1PB LEVEL
AUD IOCH2CH3CH4TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON
OFFUNITY
VA R
COUNTERRESET
A  IN
TRIM
SET
OUT IN
A  OUTCH1 CH4CH2INSERTCH3ASSEMVIDEO CUE TCSTAND BY
EDIT
REW STOPPLAY REC PLAYER
RECORDER
FF
JOGSHTLSLOW
TAPE
EEONREGENPRESETEXITOFFREMOTELOCAL
8
95
4
4
4After selecting VTR used as the player by pressing
PLAYER button, set the...

28
4Upon completion of the setting, release the search
button.
The item number now flashes.
OWhen the search dial is in the SHTL mode, the
item will move unless the dial is set to the center
position.
5When other items are to be changed, repeat steps
2to 4.
6Press the SET button.
The changes are stored in the memory.
To disregard the new settings and restore the
old settings instead, press the MENU button.
OTo return the setup contents to the factory
settings (initial settings), press the RESET
button...

29
Setup menus
1Press the MENU button.
2When the FF button is pressed while holding down
the DIAG button, the next user file is selected;
conversely, when the REW button is pressed while
holding down the DIAG button, the previous user
file is selected.
3To enter the selection made in step 2for the user
file which is to be used, press the SET button.
The user file is changed and stored in the memory. This VTR can hold five user files, each of which has
its own specific menu settings, and one of these...

30
Setup menus
1Press the MENU button.
2Press the REW button or FF button while holding
down the DIAG button to select the USER1 file.
4Turn the search dial while holding down the search
button to select the user file whose contents are to
be loaded into USER1.
6Press the PLAY button.
The settings of the user file selected in step 
4are
loaded, and the USER1 menu display appears. If
the STOP button is pressed instead, the settings
are not changed, and the USER1 menu display
appears.
7Turn the search dial...