Panasonic Aj Hdc27v Operating Instructions Manual
Have a look at the manual Panasonic Aj Hdc27v Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
71 Other VTR functions The NEWS REC function is set using NEWS REC MODE on the VTR MENU “FUNCTION” screen. By controlling the VTR START button acknowledgment time during recording (by up to 2 seconds), the time taken for the unit to transfer from the recording mode to the rec-pause mode can be delayed. In other words, by controlling the VTR start button operation acknowledgment time, the unit can continuously record without the user having to interrupt the recording: this safeguards against the failure to record those precious moments—a failure that occurs when recording is resumed immediately after it was shut down temporarily. NEWS REC function The RETAKE function is activated by selecting ON for RETAKE MODE on the VTR MENU “FUNCTION” screen. If the lens RET button is pressed while holding down the MODE CHECK button when the unit is in the rec- pause mode upon completion of a recording or subsequently in the STOP mode, the tape will be rewound to a point near the start point (a position about 10 frames ahead of the recording start point) of the final picture which was last recorded, and the unit will be set to the rec-pause mode. If there is enough leeway in the shooting time and a particular cut is clearly judged to be no good, recording can be started from that point so that the no-good cut will be deleted. By cutting down on the time taken for copying onto the work tape, for instance, this function is very effective in achieving economical operation. RETAKE function This function makes simple interval shooting (intermittent recording) possible. It proves to be particularly effective when shooting programs with a nature theme or art programs. The INTERVAL REC function is set on the VTR MENU “FUNCTION” screen. OINTERVAL REC MODE This sets the INTERVAL REC function to ON or OFF. OINTERVAL REC TIME This sets the recording time (1 cut) for interval shooting. OINTERVAL PAUSE TIME This sets the rec-pause time for interval shooting. Once the above items are set, the unit is set to the INTERVAL REC mode, and “i” starts to flash inside the viewfinder. When the VTR START button is now pressed, interval shooting is started, and “iREC” lights in place of “i.” Also, the time unit (h/min/s/frm) display on the counter display area starts to flash. When the unit is set to rec-pause mode upon completion of the first interval shooting, “iREC” goes from lighted to flashing inside the viewfinder. The time unit display on the counter display area remains flashing. INTERVAL REC (intermittent recording) function RET button MODE CHECK button i REC hminsfrm
72 Menu operations The setting menu operations are performed using the MENU button and JOG dial button. The menu configuration is divided into the camera unit’s setting menus and VTR unit’s setting menus. It is possible to select the engineer menu which enables all the setting menu items to be set or, alternatively, the user menu which consists of individually tailored menus so that only those menus which will be used most frequently can be set. The engineer menu is displayed at all times when the AJ-EC3 extension control unit (optional accessory) is connected to the unit for operating the unit by remote control. User menu The user menu was set when the unit was shipped. However, the user can change the configuration of the menus by selecting only those menus which will be used most frequently so that they will be tailored to the user’s individual needs. Set the user menu on the USER MENU SELECT screen of the engineer menu. The data settings are saved in the non-volatile memory for long-term storage. Display method OWhen the MENU button is pressed, the camera unit’s USER menu screen which was set at the time of shipment is displayed. OWhen the MENU button is pressed again, the VTR unit’s USER menu screen is displayed. OWhen the MENU button is pressed once more, the menu screen display is cleared. Engineer menu All the setting menu items can be set on this menu. The data settings are saved in the non-volatile memory for long-term storage. Display method OHold down the MENU button for at least 3 seconds. OWhen the MENU button is pressed again, the VTR unit’s MAIN MENU screen is displayed. OWhen the MENU button is pressed once more, the menu screen display is cleared. 1AB 0dBCZ73 ¢¢¢¢ VTR USER MENU ¢¢¢¢ ¢¢¢¢ CAM USER MENU ¢¢¢¢ When the power is switched on Status display Camera unit’s user menu VTR unit’s user menu Press the MENU button. Press the MENU button. Press the MENU button. MENU switch JOG dial button
73 Menu operations User menu:Engineer menu Basic setting menu operations Displaying menus CAM USER MENUPress the MENU button.Press the MENU button. Press the JOG dial button. 1Press the MENU button. The camera unit’s USER menu screen is displayed. 2When the MENU button is pressed again, the VTR unit’s USER menu screen is displayed. 1Hold down the MENU button for at least 3 seconds. 2When the JOG dial button is pressed, the next MAIN menu screen (of the camera unit) is displayed. 3When the MENU button is pressed, the VTR unit’s MAIN MENU screen is displayed. } } VTR USER MENU55CAM MAIN MENU 1 CAM MAIN MENU 2 CAM MAIN MENU 3 CAM MAIN MENU 4 Hold down the MENU button for at least 3 seconds. Press the MENU button. Press the JOG dial button. Press the JOG dial button. Press the JOG dial button. Press the JOG dial button. } } } } } } } } VTR MAIN MENU55 Press the MENU button.5 Press the MENU button.5 Press the MENU button.5
74 < ROP > nMASTER PED : +008 MASTER DTL : +00 MASTER GAMMA : 0.45 R GAIN : +000 G GAIN : +000 B GAIN : +000 R PEDESTAL : +000 G PEDESTAL : +000 B PEDESTAL : +000 Menu operations Operations common to the user menu and engineer menu Example: Displaying sub-menus and deciding on settings Turn the JOG dial button.I 1Turn the JOG dial button while the USER menu screen or MAIN menu screen is displayed. The cursor ( n) moves to the SUB menu item. 2Move the cursor ( n) to the desired SUB menu item, and press the JOG dial button. The SUB menu is now displayed. (The cursor appears in the title part of the SUB menu.) 3Turn the JOG dial button to move the cursor to the desired item to be set, and press the JOG dial button. The digit whose value is to be set now flashes. 4Turn the JOG dial button to change the setting. nCAM MAIN MENU1 ROP MATRIX COLOR CORRECTION1 COLOR CORRECTION2 LOW SETTING MID SETTING HIGH SETTING ADITIONAL DTL1 ADITIONAL DTL2 SKIN TONE DTL KNEE/LEVEL GAMMA CAMERA SETTING Example: Press the JOG dial button.InCAM MAIN MENU1 nROP MATRIX COLOR CORRECTION1 COLOR CORRECTION2 LOW SETTING MID SETTING HIGH SETTING ADITIONAL DTL1 ADITIONAL DTL2 SKIN TONE DTL KNEE/LEVEL GAMMA CAMERA SETTING n< ROP > MASTER PED : +008 MASTER DTL : +00 MASTER GAMMA : 0.45 R GAIN : +000 G GAIN : +000 B GAIN : +000 R PEDESTAL : +000 G PEDESTAL : +000 B PEDESTAL : +000 Example: Press the JOG dial button.I n< ROP > MASTER PED : +008 MASTER DTL : +00 MASTER GAMMA : 0.45 R GAIN : +000 G GAIN : +000 B GAIN : +000 R PEDESTAL : +000 G PEDESTAL : +000 B PEDESTAL : +000 Example: Press the JOG dial button.I 5When the desired setting is reached, press the JOG dial button. The setting is now entered. 6When other items are to be set, turn the JOG dial button to move the cursor, and change and enter the settings by repeating steps 3to 5. 7To move to another SUB menu, turn the JOG dial button to move the cursor to the title part of the SUB menu, and press the JOG dial button. The USER menu screen or MAIN menu screen is now displayed so proceed with operation by following the same steps. 8Upon completion of the settings, press the MENU button. The settings are now recorded, the setting menu mode is exited, and the normal operation mode is restored. To exit the camera unit’s menu, press the MENU button twice. When the MENU button is pressed once, operation is transferred to the VTR unit’s menu.
75 Setting menu configuration CAM MAIN MENU 1 ROP MATRIX COLOR CORRECTION 1 COLOR CORRECTION 2 LOW SETTING MID SETTING HIGH SETTING ADDITIONAL DTL1 ADDITIONAL DTL2 MASTER PED MASTER DTL MASTER GAMMA R GAIN G GAIN B GAIN R PEDESTAL G PEDESTAL B PEDESTAL } MATRIX TABLE MATRIX R-G MATRIX R-B MATRIX G-R MATRIX G-B MATRIX B-R MATRIX B-G R (SAT)/(PHASE) Mg (SAT)/(PHASE) B (SAT)/(PHASE)Cy (SAT)/(PHASE)G (SAT)/(PHASE)Yl (SAT)/(PHASE) R (SAT)/(PHASE) Mg (SAT)/(PHASE) B (SAT)/(PHASE)Cy (SAT)/(PHASE)G (SAT)/(PHASE)Yl (SAT)/(PHASE) } MASTER GAIN H. DTL LEVEL V. DTL LEVEL DTL CORING H. DTL FREQ LEVEL DEPEND MASTER GAMMA} BLACK STRETCH} MATRIX TABLE} COLOR CORRECTION } MASTER GAIN H. DTL LEVEL V. DTL LEVEL DTL CORING H. DTL FREQ LEVEL DEPEND MASTER GAMMA} BLACK STRETCH} MATRIX TABLE} COLOR CORRECTION } MASTER GAIN H. DTL LEVEL V. DTL LEVEL DTL CORING H. DTL FREQ LEVEL DEPEND MASTER GAMMA} BLACK STRETCH} MATRIX TABLE} COLOR CORRECTION KNEE APERTURE SLIM DTL KNEE APE LVL DTL GAIN (+) DTL GAIN (–) DTL CLIP DTL SOURCE V DTL FREQ. SKIN TONE DTL KNEE/LEVEL GAMMA CAMERA SETTING} SKIN TONE DTL } SKIN TONE ZEBRA SKIN DTL CORING Y MAX Y MIN I CENTER I WIDTH Q WIDTH Q PHASE MASTER PED } MANUAL KNEE KNEE POINT KNEE SLOPE} WHITE CLIP WHITE CLIP LVL A. KNEE POINT A. KNEE LVL R GAMMA B GAMMA DETAIL HIGH COLOR GAMMA TEST SAW FLARE H-F COMPE D4300K Items indicated with }are items whose settings can only be switched ON and OFF.
76 Setting menu configuration CAM MAIN MENU 2 VF DIAPLSY VF MARKER VF INDICATOR CAMERA ID SHUTTER SPEED ! LED CAMERA SW MODE SUPER GAIN DISP CONDITION DISP MODE VF OUTVF DTLZEBRA1 DETECTZEBRA2 DETECTZEBRA2LOW LIGHT LVL SAFETY ZONE CENTER MARK FRAME SIGMARKLVL EXTENDER SHUTTER FILTERWHITEGAINIRISCAMERA IDZOOM LVLCOLOR TEMPFRAME RATE ID: SYNCHRO SCAN1/1001/1201/2501/5001/10001/2000 GAIN (0dB) GAIN (–3dB) SHUTTERWHITE PRESETEXTENDERFILTERBLACK STRD4300KMATRIXCOLOR CORRECTIONFRAME RATE FILTER INH SHOCKLESS AWB COLOR BARSS. GAIN OFFUSER1 SWUSER2 SWS. BLK LVLECU DATA SAVE FRAME MODEFRAME RATE RANGE FRAME RATE SCAN REVERSE S. GAIN VALUE CAM MAIN MENU 3 CAM CARD READ/WRITE CAM CARD R/W SELECT GENLOCK/IRIS LENS ADJ SELECT READ SELECT WRITECARD CONFIGREAD USER DATATITLE ID READ/WRITE CAM MAIN MENU1 LEVEL R/W CAM MAIN MENU1 SW (}) R/WCAM MAIN MENU2 R/WCAM MAIN MENU3 R/WCAM MAIN MENU4 R/W H PHASE COARSEH PHASE FINEA. IRIS LEVELA. IRIS PEAK/AVEA. IRIS MODES. IRIS LEVEL F2.8 ADJ F16 ADJ
77 Setting menu configuration CAM MAIN MENU 4 CAM USER MENU SELECT1 CAM USER MENU SELECT2 BLACK SHADING FLARE INITIALIZE DIAGNOSTIC OPTION ROPLOW SETTINGMID SETTINGHIGH SETTINGADDITIONAL DTL1ADDITIONAL DTL2SKIN TONE DTLKNEE/LEVELGAMMACAMERA SETTING VF DISPLAY VF MARKER VF INDICATOR!LEDCAMERA SW MODESUPER GAIN CAM USER MENU SELECT3CAM CARD READ/WRITE CAM CARD R/W SELECT GENLOCK/IRISDETECTION CORRECT (DIG) WHITE SHADINGDETECTION (V SAW) CORRECT R FLARE G FLARE B FLARE COLORIMETRYMATRIX READ FACTORY DATA WRITE USER DATA SCENE SEL READ WRITE RESETTITLE 1TITLE 2TITLE 3TITLE 4 CAM SOFT (IN) CAM SOFT (OUT) GAMMA GAINGAMMA RAMKNEEALCPLD SHD, ABB SW CTRLAWB AREA EVALUATION ENG SECURITY S/NS/N DETAIL H-F COMPE. GAMMA MATRIX FLARE M. PED MODULATIONMODULATION DETAIL H-F COMPE. GAMMA MATRIX FLARE M. PED RESOLUTIONRESOLUTION DETAIL H-F COMPE. GAMMA MATRIX FLARE M. PED SENSITIVITYSENSITIVITY KNEE W. CLIP M. PED
78 Setting menu configuration VTR MAIN MENU FUNCTION BATTERY/TAPE VTR VF INDICATOR MIC/AUDIO TIME/DATE NEWS REC MODE HUMID OPE REC STARTPAUSE TIMERRETAKE MODEHD SDI OUTINTERVAL REC MODEINTERVAL REC TIMEINTERVAL PAUSE TIME BATTERY SELECT EXT DC IN SELECT BATT NEAR END ALARMBATT NEAR END CANCELBATT END ALARMBATT REMAIN FULLTAPE NEAR END ALARMTAPE NEAR END TIMETAPE END ALARMTAPE REMAIN/$BATTERY SETTINGAJ-BP490 AU-BP402 HP-30APRO14TRIM14TRIM13DIGITAL14DIGITAL13BP-H90BP-H100NP-L40NP-L40 DBP-L60/90NP-1B TAPE (IND) BATTERY (IND) LEVEL METER (IND)AUDIO IN (IND)TC (IND)VTR WARNING (IND)SAVE LED FRONT MIC POWER MIC LOWCUT CH1 MIC LOWCUT CH2LIMITERTEST TONEREC CH3/CH4CUE SELECTCUE REC TC/UBTC MODE UB MODE TCG SET HOLDFIRST REC TCP.OFF LCD DISPLAYTC OUTVITC UB MODE DIAGNOSTICOPERATION DRUM RUNNING THREADINGVTR SYSCONSERVOMECHACONFRONT YEAR MONTH DAYHOURMINUTE$ TIME/DATE SET VTR CARD READ/WRITEREAD WRITE READ USER DATA VTR INITIALIZEREAD FACTORY DATA WRITE VTR USER DATA VTR USER MENU SELECT FUNCTIONNEWS REC MODE HUMID OPE REC STARTPAUSE TIMERRETAKE MODEHD SDI OUTINTERVAL REC MODEINTERVAL REC TIMEINTERVAL PAUSE TIME BATTERY/TAPEBATTERY SELECT EXT DC IN SELECT BATT NEAR END ALARMBATT NEAR END CANCELBATT END ALARMBATT REMAIN FULLTAPE NEAR END ALARMTAPE NEAR END TIMETAPE END ALARMTAPE REMAIN/ $ VTR VF INDICATORTAPE (IND) BATTERY (IND) LEVEL METER (IND)AUDIO IN (IND)TC (IND)VTR WARNING (IND)SAVE LED MIC/AUDIOFRONT MIC POWER MIC LOWCUT CH1 MIC LOWCUT CH2LIMITERTEST TONEREC CH3/CH4CUE SELECTCUE REC TC/UBTC MODE UB MODE TCG SET HOLDFIRST REC TCP.OFF LCD DISPLAYTC OUTVITC UB MODE
79 Setting menu screens (CAM MENU) The main menu consists of CAM MAIN MENU (1 to 4) of the camera and the VTR MAIN MENU of the VTR. These screens are index screens which are used to open the sub-menus. The setting menu is operated with the MENU button and JOG dial button. (Refer to pages 72 to 74 for the menu operations.) CAM MAIN MENU 1 screen SUB menuVF displayRemarks ROPUSER ENGIndex for opening the ROP screen. MATRIXUSER ENGIndex for opening the MATRIX screen. COLOR CORRECTION1USER ENGIndex for opening the COLOR CORRECTION 1 screen. COLOR CORRECTION2USER ENGIndex for opening the COLOR CORRECTION 2 screen. LOW SETTINGUSER ENGIndex for opening the LOW SETTING screen. MID SETTINGUSER ENGIndex for opening the MID SETTING screen. HIGH SETTINGUSER ENGIndex for opening the HIGH SETTING screen. ADDITIONAL DTL1USER ENGIndex for opening the ADDITIONAL DTL 1 screen. ADDITIONAL DTL2USER ENGIndex for opening the ADDITIONAL DTL 2 screen. SKIN TONE DTLUSER ENGIndex for opening the SKIN TONE DTL screen. KNEE/LEVELUSER ENGIndex for opening the KNEE/LEVEL screen. GAMMAUSER ENGIndex for opening the GAMMA screen. CAMERA SETTINGUSER ENGIndex for opening the CAMERA SETTING screen. CAM MAIN MENU 2 screen SUB menuVF displayRemarks VF DISPLAYUSER ENGIndex for opening the VF DISPLAY screen. VF MARKERUSER ENGIndex for opening the VF MARKER screen. VF INDICATORUSER ENGIndex for opening the VF INDICATOR screen. CAMERA IDENG Index for opening the CAMERA ID screen. SHUTTER SPEEDENG Index for opening the SHUTTER SPEED screen. !LEDUSER ENGIndex for opening the !LED screen. CAMERA SW MODEUSER ENGIndex for opening the CAMERA SW MODE screen. SUPER GAINUSER ENGIndex for opening the SUPER GAIN screen. FRAME MODEUSER ENGIndex for opening the FRAME MODE screen. CAM MAIN MENU 3 screen SUB menuVF displayRemarks CAM CARD READ/WRITEUSER ENGIndex for opening the CAM CARD READ/WRITE screen. CAM CARD R/W SELECTUSER ENGIndex for opening the CARD R/W SELECT screen. GENLOCK/IRISUSER ENGIndex for opening the GENLOCK/IRIS screen. LENS ADJUSER ENGIndex for opening the LENS ADJ screen. CAM MAIN MENU 4 screen SUB menuVF displayRemarks CAM USER MENU SELECT1USER ENGIndex for opening the CAM USER MENU SELECT 1 screen. CAM USER MENU SELECT2USER ENGIndex for opening the CAM USER MENU SELECT 2 screen. CAM USER MENU SELECT3USER ENGIndex for opening the CAM USER MENU SELECT 3 screen. BLACK SHADINGUSER ENGIndex for opening the BLACK SHADING screen. WHITE SHADINGUSER ENGIndex for opening the WHITE SHADING screen. FLAREUSER ENGIndex for opening the FLARE screen. COLORIMETRYUSER ENGIndex for opening the COLORIMETRY screen. INITIALIZEUSER ENGIndex for opening the INITIALIZE screen. DIAGNOSTICUSER ENGIndex for opening the DIAGNOSTIC screen. EVALUATIONUSER ENGIndex for opening the EVALUATION screen. OPTIONUSER ENGIndex for opening the OPTION screen.
80 Setting menu screens (CAM MAIN MENU 1) ROP screen The ROP (Remote Operation Panel) is set on this screen. ItemVariable rangeRemarks MASTER PED–200 : +18 : +200 (Max.)VF display USER ENGMASTER PEDESTAL level setting. MASTER DTL –31 : +00 : +31 USER ENGH. DTL/V. DTL level setting. MASTER GAMMA0.35 : 0.45 : 0.75 USER ENGMASTER GAMMA setting. (0.01 step) Three different values can be stored for LOW, MID and HIGH in the memory. R GAIN –200 : +000 : +200 (Max.)USER ENGFor setting R channel gain. G GAIN –200 : +000 : +200 (Max.)USER ENGFor setting G channel gain. B GAIN –200 : +000 : +200 (Max.)USER ENGFor setting B channel gain. R PEDESTAL –100 : +000 : +100 (Max.)USER ENGFor setting R channel PEDESTAL level. G PEDESTAL –100 : +000 : +100 (Max.)USER ENGFor setting G channel PEDESTAL level. B PEDESTAL –100 : +000 : +100 (Max.)USER ENGFor setting B channel PEDESTAL level. The underlining in the variable range column indicates the setting in the preset mode. MATRIX screen The camera matrix is set on this screen. ItemVariable rangeRemarks MATRIX TABLEA B VF display USER ENGFor selecting the color adjustment display. MATRIX R-G –31 : +00 : +31 USER ENGColor adjustment MATRIX R-B –31 : +00 : +31 USER ENGColor adjustment MATRIX G-R –31 : +00 : +31 USER ENGColor adjustment MATRIX G-B –31 : +00 : +31 USER ENGColor adjustment MATRIX B-R –31 : +00 : +31 USER ENGColor adjustment MATRIX B-G –31 : +00 : +31 USER ENGColor adjustment OThe white balance and black balance will not change even if the MATRIX is changed. OTwo tables, A and B, can be stored in the memory for the MATRIX TABLE item. O“00” applies for all the preset modes in MATRIX TABLE B.