Panasonic Aj Hdc27fp Operating Instructions Manual

							21
7“+” button, “–” button
These are used to increment or decrement by 1 the
figure in the digit which was made to flash by the
SHIFT button 8when the time code or user’s bit is
to be set.
8SHIFT button
This causes the digit to be set to flash when the
time code or user’s bit is to be set.
9TCG (time code selector) switch
This is used to set the running mode of the built-in
time code generator.
F-RUN:Set here to have the time code run all the
time regardless of the VTR’s operation.
This position is used to align the time code
with the time or externally lock the time
code.
SET:Set here when the time code or user’s bit is
to be set.
R-RUN:Set here to have the time code run only
during recording.
The time code on the tape with scene-to-
scene continuity is recorded continuously.
Time code related section (2)
4HOLD button
The time data display of the counter display section
which was on the screen at the moment when this
button is pressed is held.  (However, the time code
generator keeps running.)  When the button is
pressed again, the hold status is released.
It is used, for instance, to find out the time at which
a particular scene was shot.

If the HOLD button is pressed and held down while
the DISPLAY switch 6has been set to UB,
“HOLD” on the counter display flashes, and the
button functions to display the VITC user’s bit
information recorded in the video AUX area on the
counter display section.
5RESET button
This is used to reset the time data on the counter
display section to “00:00:00:00.”  If it is pressed
while the TCG switch 9is at the SET position, the
time code data and user’s bit data are respectively
reset to “00:00:00:00.”
6DISPLAY switch
This is used to display the time code, CTL or user’s
bit on the counter display section depending on the
setting positions of this switch and the TCG switch
9.
UB:The user’s bit is displayed.
TC:The time code is displayed.
CTL:CTL is displayed.
Parts and their functions
46
789
5 
						

							Removal lever
Battery pack
22
Power supply
Using the Anton/Bauer battery packA battery pack or an AC power source can be used as
this unit’s power supply.
To use the battery pack, there is a choice of
makes of batteries below, namely: 
OAnton/Bauer
OIDX
OSony

Batteries of other makes can also be supported by
changing the setting menu but no guarantees are
made for the system when they are actually used with
this unit.
Before using the battery pack, recharge the battery
using the battery charger.
(For details on the recharging method, refer to the
operating instructions of the battery concerned.)

An intelligent battery system and ultra light system are
supported.
The remaining battery charge displayed inside the
viewfinder is usually shown as a percentage of the full
charge, but when the battery charge is nearly
completely dissipated, the percentage display is
replaced with a voltage display.
1Attach the battery pack.
Insert the pack in the direction shown by the
arrows, and then slide it into position.
2To detach the battery, pull the battery mount
removal lever all the way down, and slide the
battery pack in the direction shown by the arrow. 
						

							23
Power supply
Using the BP-90 type battery pack

ODo not pull the rubber cap forcefully.
OWhen mounting the battery case, take care not to
pinch the connecting cord.
4Attach the AU-M402H battery case.
Open the battery case cover, and raise it above the
rubber cap: screw holes will now be visible.
Tighten the screws using a screwdriver, then
attach the case to the NP/BP adapter plate and
tighten the screws fully.
5Connect the plug on the battery pack to the
connector inside the case, and insert the battery
pack.

Before connecting or disconnecting the plug, be
absolutely sure to turn off the unit’s power.
3Connect these connectors with the connector on
the AU-MA402H battery case.
1Attach the NP/BP adapter plate.
Insert it in the direction shown by the arrows, and
slide it into place.
2Attach the connectors provided with the NP/BP
adapter plate to the positions shown in the figure. 
						

							24
Power supply
Using the Sony NP-1/BP-90 battery
pack
Attach the Sony battery holder.  As shown in the
figure, attach the battery case with the cover detached
and then the detached cover.
1Tighten the mounting screws.
2Tighten the power contact screws.
3Insert the top of the detached cover in the direction
shown by the arrows.
4Align the holes in the bottom of the cover (metal
part) with the holes at the bottom of the case, and
use the screws to attach the case.

When mounting the battery holder, take care not to
pinch the connecting cord.
Using the V-mount type battery
pack
1
3
4
2
Battery case for NP-1
Battery case for BP-90
2
1
3
4
Attach the V-mount adapter plate.
Insert it in the direction shown by the arrows, and slide
it into place.
Please consult your local dealer for any questions
regarding the NP/BP adapter plate or V-mount
adapter plate. 
						

							25
Using an AC power supply
When the AJ-B75 AC adapter is used

OCheck the pin signals of the DC IN socket when
using an external power supply other than the AJ-
B75 AC adapter. (DC 12 V, 8.5 A)
OPower from the AC adapter takes precedence when
both a battery pack and AC adapter have been
connected.
OWhen using the AC adapter, be absolutely sure to
first set the power of the AC adapter to ON and
then set the unit’s power switch to ON.
If the power is turned on in the reverse sequence,
the output voltage of the AC adapter will rise
gradually, and the unit may malfunction as a result.
12 3 4
1Connect the DC OUT connector on the AJ-B75 AC
adapter to the DC IN socket on the unit.
2Set the power of the AC adapter to ON.
3Set the unit’s power switch to ON.
Pin no. Signal
1 GND
2, 3==
4 +12 V
Power supply
DC IN socket 
						

							26
Attaching the lens
1Raise the lever for securing the lens, and detach
the mount cap.
2Align the center mark of the lens with the groove in
the top center of the lens mount, and attach the
lens.
3Push down the lever for securing the lens to
secure the lens.
4Push the cable into the cable clamp, and connect it
to the LENS socket.

OFor details on handling the lens, refer to the
operating instructions which accompany the lens.
OThe following lens adjustments and camera
adjustments may be necessary depending on the
lens mounted.
1. Lens flange back adjustment
2. Lens auto iris operating speed adjustment
3. Lens white shading adjustment (performed on
the unit)
Lever for securing
the lens
MarkLENS socket Mount cap 
						

							27
Adjusting the lens flange
If the subject is not focused properly in the telephoto
and wide-angle modes during zoom operations, adjust
the flange back (distance from the lens mounting
surface to the image-forming surface).
Once this adjustment is done, it need not be redone
unless the lens is replaced.
Adjustment method
1Attach the lens to the camera.
At this stage, do not forget to connect the lens
cable.
2Set the lens aperture to manual and open the
aperture.
3Set the lighting in such a way that the appropriate
video output level is achieved at a distance of
about 3 meters away from the chart used for the
flange back adjustment.
If the video level is too high, use the filters and
shutter.
4Loosen the screw securing the F.f (flange focus)
ring.

On some lenses, this may be marked as F.b
(flange back) ring.
5Set the zoom ring to the telephoto position either
manually or electrically.
6Shoot the chart used for the flange back
adjustment, and turn the distance ring to adjust the
focus.
7Set the zoom ring to the wide-angle position, and
turn the F.f ring to adjust the focus.
Take care not to move the distance ring during this
process.
9Tighten the screw securing the F.f ring.
8Repeat steps 5to 7until the focus is adjusted at
both the telephoto and wide-angle positions. 
For details on the adjustment method and lens
positions, refer also to the operating instructions that
accompany the lens.
Approx. 3
meters 
						

							28
Adjusting the white shading
Follow the procedure outlined below when the white
shading needs to be re-adjusted.
Adjustment method

OThe method below can be used for the white
shading adjustments with most lenses.  However,
with some very special lenses, a different
adjustment method may be necessary.
OEven when the white shading has been adjusted,
tinting may occur in the vertical direction near the
lens aperture open position.  This is a phenomenon
which is inherent to lenses and optical systems and
is not indicative of malfunctioning.
SHUTTER: OFFGAIN: L (0 dB)JOG dial buttonMENU button
1Attach the lens to the camera.
At this stage, do not forget to connect the lens
cable.
2Set the electronic shutter to OFF, and set the gain
to “L (0 dB).”
3If the lens is provided with an extender, disengage
the extender function.
41Perform the menu operations (pages 84 to 86),
and display the “VF DISPLAY” screen of FILM
(CAM) MAIN MENU 2.
2Set ZEBRA1 DETECT to 70%, ZEBRA2
DETECT to 85% and ZEBRA2 to SPOT.
3Press the MENU button and close the menu
screen.
4Set the ZEBRA switch on the viewfinder to ON.
5Shoot a sheet of white paper devoid of color
irregularities.

Since flicker tends to occur under fluorescent
lights, mercury lamps and other such lights, use a
source of light such as sunlight or a halogen lamp
which does not tend to produce flicker.
6Set the lens aperture to manual, and adjust the
lens aperture in such a way that ZEBRA fills the
whole screen.
Check that the lens aperture is between F/4 and
F/11.

OSince unevenness in the lighting will make it
impossible for ZEBRA to fill part of the screen,
try adjusting the lighting position, etc.
OTry adjusting the lighting position, etc. also when
the lens aperture is not between F/4 and F/11.
OAlways be sure to leave the electronic shutter at
OFF. 
						

							29
Adjusting the white shading
AUTO W/B BAL
switchWHITE BAL switch:
“A” or “B”
71Set the WHITE BAL selector switch to “A” or “B,”
and initiate the automatic white balance (AWB)
adjustment using the AUTO W/B BAL switch.
2Initiate the automatic black balance (ABB)
adjustment using the AUTO W/B BAL switch.
3Initiate the automatic white balance (AWB)
adjustment again using the AUTO W/B BAL
switch.
91Perform the menu operations (pages 84 to 86),
and display the “WHITE SHADING” screen of
FILM (CAM) MAIN MENU 4.
2Turn the JOG dial button to move the cursor to
the DETECTION, and press the JOG dial
button.
“ACTIVE” now appears on the screen to indicate
that the white shading is being automatically
adjusted.
The adjustment is completed when the
“ACTIVE” display is cleared.
3Press the MENU button to close the menu
screen.
8Repeat step 6.
10If the lens is provided with an extender, engage
the extender function, and repeat steps 
6to 9.
The white shading adjustment is now complete.
The adjusted values are retained in the non-volatile
memory so that there is no need to adjust the white
shading again even after the unit’s power is turned off.
JOG dial buttonMENU button 
						

							30
Adjusting the viewfinder (The viewfinder is an optional accessory.)
Attaching the viewfinder
1Check that the camera’s POWER switch is at OFF.
2Connect the plug to the viewfinder connecting
terminal.

When connecting the plug to the viewfinder
connecting terminal, push the plug firmly into
place.
3Push the viewfinder down.
4Tighten the stopper screw firmly.
Detaching the viewfinder
1Check that the camera’s POWER switch is at OFF.
2Loosen the stopper screw, pull the viewfinder
straight up, and draw it out.

Use both hands to draw the viewfinder out.  It may
not be possible to remove the viewfinder smoothly
with one hand, which may cause damage to it.
3Disconnect the plug from the viewfinder connecting
terminal.
Stopper screw
Stopper screw