Panasonic Aj Hd130dc Operating Instructions Manual

21
Setup (Initial Settings)
SET–UP MENU 
2NO
FACTORY
USER (ALL)
USER (NOT SYSTEM)
Press the MENU-UP button or MENU-DOWN
button to move the cursor to FACTORY, and
press the SET button.
OIf the cursor is moved to FACTORY and this
operation is performed, the factory settings are
restored for all the menus with the exception of
the SYSTEM menu.
OIf the cursor is moved to NO and this operation
is performed, operation returns to the menu
screen without restoring the factory settings.4
Press the MENU-UP button...

22
How to load the user defaults
Set the LOCAL/MENU/REMOTE switch to the
MENU position.
The VTR is set to the menu setting mode, and
the menu screen is displayed on the video
monitor.1
Press the RESET button.
The VTR is set to the default setting mode, and
the default setting screen is displayed on the
video monitor.2
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the LOAD
position, and press the SET button.
The VTR is set to the LOAD mode, and the
LOAD screen is displayed on the...

23
Press the MENU-UP button or MENU-DOWN
button to move the cursor to NO, and press
the SET button.
The menu protection function is now released.3
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
The unit is now set to the menu protection mode.
When the LOCAL/MENU/REMOTE switch is set
to the MENU position, the VTR is not set to the
menu setting mode, and “MENU PROTECTED”
appears on the video monitor screen.

If, while the menu protection mode is being set,
the LOCAL/MENU/REMOTE switch is...

24
SYSTEM
Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
12 SYS H (HD) 0550
:
1100
:
1650–550
:
0:
550For adjusting the system phase of the HD SDI output (in 27 ns steps).
–: The phase is moved ahead.
+: The phase is moved back.
The underlining denotes the factory mode.
14 SYS SC (SD) 0000
:
0108
:
0216–108
:
0:
108For adjusting the system phase of the VIDEO output and SD SDI output.
(Total variable range: ±180 degrees or more)
–: The phase is moved ahead.
+: The...

25

OIf the PAGE button and the DATA+ or DATA– button are pressed together when menu item No.007
(CHARA H-POS) and No.008 (CHARA V-POS) are being set, the counter display appears temporarily
while these buttons are held down to enable the settings to be checked.
It is also possible to use the DATA+ button and DATA– button while holding down the PAGE button to
perform the settings while at the same time checking their actual status.
OEven when “OFF” is selected as the menu item No.005 (SUPER) setting, the...

26
009 CHARA TYPE
0000
0001WHITEW/OUTFor setting the superimposed display and the menu display type.
0: White characters are displayed on a black background.
1: White characters with black borders are displayed.
020 SYS FORMAT
0000
00011080i720pFor setting the format used to record and play back signals including the
HD REF signal.
0: 1080i mode
1: 720p mode
022 PB FORMAT
0000
0001MANUALAUTOFor setting the format used for playing back the tape.
0: The menu item No.020 (SYS FORMAT) setting is complied...

27
101 SHTL MAX
0000
0001
X8.4
X16
For setting the maximum shuttle mode speed when using the external
controller connected to the 9-pin remote connector.
0: 8.4anormal speed
1: 16anormal speed
104 REF ALARM
0000
0001
OFF
ON
For setting whether the warnings are to be indicated when the REF VIDEO
has not been connected.
1: No warnings are indicated.
2: Warnings are indicated by the STOP lamp which flashes.
152HUMID OPE
0000
0001OFFON
For setting the operation to be performed when condensation has formed....

28
OPERATION
Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
The underlining denotes the factory mode.
Setup Menus
154 AUTO BACK
0000
0001
0002OFF
REC-PALLFor setting the operation method used for the frame-to-frame continuity
function.  (This item activates the AUTO BACK function to rewind the tape
for several seconds in order to ensure a smooth continuity between the
recorded images.)
0: No AUTO BACK operation.
1: In the REC PAUSE mode, the AUTO BACK function is...

29
400 STILL TIMER 0000
0001
0002
0003
0004
0005
0006
0007
00080.5S
5S
10S
20S
30S
40S
50S
1min
2minFor setting the time taken before the unit is set to the tape protection mode
when it has been left in the STOP or STILL mode.
(Unit: S = seconds, min: minutes)
401 SRC PROTECT
0000
0001STEPHALFFor setting the tape protection mode operation when the unit has been left
in the STILL mode.
0: STEP FWD
1: STANDBY OFF (half loading)

When STEP FWD has been set, the unit is automatically transferred to the...

30
500 VITC BLANK
0000
0001
BLANK
THRU
For setting whether to output the VITC signal to the position set by menu
item No.501 (VITC POS-1) and No.502 (VITC POS-2).
0: The VITC signal is not output.
1: The VITC signal is output.

This setting is only effective for SD outputs (VIDEO output and SD SDI
output).
501 VITC POS-1 0000
:
0006
:
001010L
:
16L:
20LFor setting the position where the VITC signal is to be inserted.

OThe same line as that set for menu item No.502 (VITC POS-2) cannot
be set.
OThis...