Panasonic Aj D910wa Operating Instructions Manual

–41–
Audio Input Preparations
Mounting a Wireless Microphone
When using the Panasonic wireless microphone system, mount the WX-RA700 wireless receiver.
ÁSee the Handling Instructions for the WX-RA700 wireless receiver for wireless receiver ope-
rations.
Connecting an Audio Component
When using an audio component as the line input signal source, connect the audio component to
the unit’s AUDIO IN CH1/CH2 connectors.
To the AUDIO OUT Connector
WX-RA700
Wireless Receiver
WX-R980
Camera Attachment
AJ-D910WA...

–42–
Mounting the Unit to a Tripod
When mounting the unit to a tripod, use an optional tripod attachment.
1Mount the tripod attachment (SHAN-TM700) onto the tripod.
Select the attachment hole in consideration of the unit’s and tripod attachment’s center of
gravity. In addition, check that the diameter of the selected hole matches the diameter of the
universal head’s camera mounting screw.
|Note{
When the tripod attachment pin does not return to its original position after the camera has been
detached,...

–43–
Mounting the Shoulder Belt
|Note{
When mounting and removing the shoulder belt, press on the top of the hooks to check that the
belt is securely mounted.
Shoulder Belt
Press to open the hook.
To remove the shoulder belt, open the hooks and then remove the belt.
Press 

–44–
Adjusting the Shoulder Pad Position
The shoulder pad can be slid up to 2/5½ in the forward-backward direction from the center position
(the position when shipped from the factory). Adjust the shoulder pad position to facilitate opera-
tion of the unit.
1Loosen the two screws.
2Slide the pad in the forward-backward direction to select an appropriate position.
3Tighten the screws to clamp the pad.
Bottom
Screws
Shoulder Pad 

–45–
Attaching the Rain Cover
Attach the rain cover as shown in the figure below.
Secure the surface fastener.Tighten the Cord.
When mounting the unit to the tripod
attachment, mount the unit using this hole.Secure the surface fastener. 

–46–
ECU AQOUTPUT
GAIN
WHITE
BALANCE
AUTO W/B
BALANCE
9
0
-3CAMERATEST
BAR
A
B
PRE
AWB
ABB
MANUAL AUTO
(dB)
SHUTTER
PAINTING
ON
OFF ON1/250
1/125
1/100 1/500
1/1000
1/2000OFF
ECU
RB
RB
MASTERPEDESTALIRIS 
ON
OFFPAGE
ITEMUPDWNONSELECT CONTROL STORESET UP
GAIN
BLACK
-
Connecting the AQ-EC1 Extension Control Unit (Option)
Connecting the AQ-EC1 extension control unit (option) allows a portion of the camera section
functions to be operated by remote control.
When the AQ-EC1 is connected and the POWER switches...

–47–
Displaying Menus on the View finder Screen
Displaying the Setting Menu Inside the Viewfinder
The setting menus are displayed on the viewfinder screen when the MENU SET/OFF switch is set
to the SET position.
There are two types of setting menus, MAIN menus and SUB menus.
Setting menus are displayed in 1-page increments.
All the pages contained in the setting menus and how each page is configured are shown in the
table below.
The menu configuration can be changed to suit a particular objective....

–48–
Checking and Selecting the Master Gain Set tings
Checking and selecting the master gain setting
1The menu shown in the figure below is displayed when the MENU SET ON/OFF switch is set
to SET while the HOLD button is held down.
2The current low, mid and high gain settings are displayed.
3Press the SHIFT/ITEM button, and move the arrow (cursor) to the LOW, MID or HIGH GAIN
menu item.
4Set the gain by pressing the UP or DOWN button. Any value from p3 dB to o30 dB can be
set.
¢
|{
GA I N M
M
M ASTER GA...

–49–
Selecting the Color Bar Set ting
Selecting the color bar setting
1The menu shown in the figure below is displayed when the MENU SET ON/OFF switch is set
to SET while the HOLD button is held down.
2To select the color bar menu item, press the SHIFT/ITEM button, and move the arrow (cur-
sor) to COLOR BAR.
3Select the color bar setting by pressing the UP or DOWN button. The SMPTE or SNG setting
can be selected.
|
¢
{
GA I N M
M
M ASTER GA I
I
IN
:
:
:
: HHD LO
G
P CO OWGA I N
GA I N
BAT TERY SE L |...

–50–
Checking the DIAGNOSTIC Screen Set ting
1
Set the MENU SET ON/OFF switch to SET while the HOLD button is held down.
2Press the PAGE button.
3The menu screen shown in the figure below appears, and it is now possible to check the
DIAGNOSTIC screen settings.
4To close the menu screen, return the MENU SET ON/OFF switch to OFF.
DIAGNOST IC{
OPERA T I ON:
:
:00000·
1
DRUM RUNN I NG
THREAD I NG
VTR SYSCON
SYSCONVe r|
P
CAM
DA T ROMA0
1.00{
Ve r|
1.0 1.0{
Ve r|
1.0{
DV V e r|
1.00{
·
·
.·
·
.·
·
h
00000·...