Panasonic Aj D810a Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj D810a Operating Instructions Manual. The Panasonic manuals for Camera are available online for free. You can easily download all the documents as PDF.
Page 61
–61– Status Displays Inside the View finder Screen Display Mode (DISP MODE) and Setting Change Message Messages informing of the contents of changed settings and adjustment results can be limited to part of the displayed items or not displayed for all items. The conditions under which messages are displayed and the corresponding display modes are shown in the table below. Setting change/adjustment results messages and display modes Conditions under which messages are displayed When the filter selection...
Page 62
–62– Status Displays Inside the View finder Screen Changing the Display Mode The display mode setting appears on the “VF DISPLAY” SUB menu page of MAIN menu screen 2 of 4. 1Set the MENU SET/OFF switch to the SET position while the SHIFT/ITEM button and UP button are held down together. 2Press the PAGE button to display the MAIN menu screen 2 of 4. 3Press the SHIFT/ITEM button to move the cursor to the “VF DISPLAY” position. 4Press the UP or DOWN button to open the VF DISPLAY page. 5Press the SHIFT/ITEM...
Page 63
–63–
{
CAMERA I D
ID
:
¢
|
EEEEEEE EEE
Status Displays Inside the View finder Screen
Setting the Camera ID
The camera ID can be set at the CAMERA ID page of the setting menu.
A camera ID of up to ten characters including English letters, symbols and spaces can be used.
The camera ID is recorded when the OUTPUT/AUTO KNEE switch is set to BARS and the color
bar signal is being recorded. It is also displayed on the viewfinder screen.
|Note{
When the setting menu is displayed, the camera ID is not displayed...
Page 64
–64– CH1 CH2 20 0 EMPHASIS dB 10 30 40 E TAPE F E BATT F RFSERVOHUMID SLACK DF SLAVE TCG HOLD h min s frm CH1 CH2 20 0 EMPHASIS dB 10 30 40 E TAPE F E BATT F RFSERVOHUMID SLACK DF SLAVE TCG HOLD h min s frm Displays Remaining Battery Level and Audio Level Displays Audio CH level meter VTR Section Operation/Status-Related Displays Warning display RF:Lights when video head clogging occurs. SERVO:Lights when the servo is out of order. HUMID:Lights when condensation occurs on the head drum. SLACK:Lights when...
Page 65
–65– CH1 CH2 20 0 EMPHASIS dB 10 30 40 E TAPE F E BATT F RFSERVOHUMID SLACK DF SLAVE TCG HOLD h min s frm Displays Time Code-Related Displays Relationship between the TCG and DISPLAY switch setting positions and the time counter display The item displayed in the time counter display is determined by the TCG switch and DISPLAY switch settings. Time code-related switch settings and display items These lamps light to indicate the time code, CTL and real time displays. DF:This lamp lights during drop frame...
Page 66
–66– Adjusting the Time and Date Adjustment and setup using the setting menu 1Set the MENU SET/OFF switch to the SET position while the SHIFT/ITEM button and UP button are held down together. 2Press the PAGE button to display the MAIN menu screen 3 of 4. 3Press the SHIFT/ITEM button to move the cursor to the “TIME/DATE” position. 4Press the UP or DOWN button to open the TIME/DATE page. 5Press the SHIFT/ITEM button to select the item to be changed. 6Press the UP (or DOWN) button to change the setting...
Page 67
–67– Adjustments and Setup During Recording Adjustments and Setup Using the Setting Menu Adjustments and setup operations during recording are performed at the setting menu. Setting menu operations are basically performed according to the procedures described on page 52. However, these procedures vary slightly according to the item. Items which can be adjusted or set up at the setting menu are as follows. Adjustment/setup items at the setting menu Adjustment/setup item Setting the gain selector value...
Page 68
–68– Adjustments and Setup During Recording Setting the Gain Selector Value When shooting in locations without sufficient brightness, bright images can be obtained by raising the gain. However, care should be taken as raising the gain also increases the noise. The gain value for the image amplifier is selected by the GAIN switch. The gain values corre- sponding to the L, M and H positions of the GAIN switch are set at the MASTER GAIN page of the setting menu. Setting the gain selector value 1Set the MENU...
Page 69
–69– Adjustments and Setup During Recording Selecting Functions The VTR’s operation functions can be selected on the “VTR FUNCTION” page of the setting menu. To select the required functions 1Set the MENU SET/OFF switch to the SET position while the SHIFT/ITEM button and UP button are held down together. 2Press the PAGE button to display the MAIN menu screen 2 of 4. 3Press the SHIFT/ITEM button to move the cursor to the “VTR FUNCTION” position. 4Press the UP or DOWN button to open the VTR FUNCTION page....
Page 70
–70– Adjusting the White Balance/Black Balance Adjusting the White Balance Adjusting the white balance and black balance in the order of AWB (white balance adjustment)>ABB (black balance adjustment)>AWB will provide a better picture. The black balance does not normally need to be readjusted even when the power is turned off and then turned back on. However, the white balance must be readjusted when the lighting conditions change. If black balance and white balance adjustments are started when the display...