Panasonic Aj D700_200dpi Operating Instructions Manual

							Mounting a Wireless Microphone
When using the Panasonic wireless microphone system, mount the WX-RA700 wireless receiver.
To the AUDIO OUT Connector
WX-RA700
Wireless Receiver
WX-R980
Camera Attachment
XLR Cable
AUDIO IN switch:
Set the AUDIO IN switch of
the channel to which the
audio signal source is
connected to REAR [LINE].Connect to the AUDIO IN CH1or CH2 Connector.
When detaching the
wireless microphone,
press up the lever on the
bottom of the camera
attachment (1) and detach
the microphone in the
upward direction (2).
(2)
LeverAJ-D700 Main Unit
(1)
See the Handling Instructions for the WX-RA700 wireless receiver for wireless receiver opera-
tions.
Connecting an Audio Component
When using an audio component as the line input signal source, connect the audio component to
the unit’s AUDIO IN CH1/CH2 connectors.
Audio Equipment
AUDIO IN Switch:
Set the AUDIO IN Switch of
the channel to which the
audio signal source is
connected to REAR [LINE].Connect to the AUDIO IN
CH1/CH2 Connectors.
-41- 
						

							Mounting the Unit to a Tripod
When mounting the unit to a tripod, use an optional tripod attachment.
1Mount the tripod attachment to the tripod.
Select the attachment hole in consideration of the units and tripod attachment’s center of
gravity. In addition, check that the diameter of the selected hole matches the diameter of the
universal head’s camera mounting screw.
Tripod Attachment
2Mount the camera to the tripod attachment.
Slide the unit forward along the grooves until a clicking sound is heard.
When detaching the tripod attachment
Hold down the red lever and move the black lever in the direction of the arrow.
Red Lever
Black Lever

When the tripod attachment pin does not return to its original position after the camera has been
detached, hold down the red lever and move the black lever in the direction of the arrow again to
return the pin to its original position.
Care should be taken as the camera cannot be mounted if the pin remains in the center.
-42- 
						

							Mounting the Shoulder Belt 
						

							Adjusting the Shoulder Pad Position
The shoulder pad can be slid up to    ” in the forward-backward direction from the center position
(the position when shipped from the factory). Adjust the shoulder pad position to facilitate opera-
tion of the unit.
1Loosen the two screws.
2Slide the pad in the forward-backward direction to select an appropriate position.
3 Tighten the screws to clamp the pad.
Screws
Shoulder Pad
Bottom
- 44 - 
						

							Attaching the Rain Cover
Attach the rain cover as shown in the figure below.
Tighten the Cord.
Secure the surface fastener.When mounting the unit to the tripod
attachment, mount the unit using this hole.
-45- 
						

							Connecting the AQ-EC1 Extension Control Unit (Option)
Connecting the AQ-EC1 extension control unit (option) allows a portion of the camera section
functions to be operated by remote control.
When the AQ-EC1 is connected and the POWER switches of the unit and AQ-EC1 are set to ON,
the unit automatically enters remote control mode.
The handling instructions included with the AQ-EC1 describe operations for when the AQ-EC1 is
connected to an AQ series digital camera.
When the AQ-EC1 is connected to the AJ-D700, some functions differ, and some features cannot
be used.
6-pin Cable
ECU Connector
AQ-EC1

The POWER switches of the unit and AQ-EC1 must be set to OFF before the 6-pin cable is
connected or disconnected.
All adjustments and settings made using the switches and controls other than the menu setting
section of the AQ-EC1 are erased when the unit’s POWER switch is set to OFF. Also, adjust-
ments and settings made using the AQ-EC1 cannot be written to setup cards. However, when
the AQ-EC1 is connected again, these settings return to the AQ-EC1 settings.
(Menu contents set with the menu setting section are saved.)

The functions of the AQ-EC1 are limited as follows.
The STORE switch does not function.
(If the menu settings are changed while the AQ-EC1 is connected to the AJ-D700, the new menu
settings are saved automatically as soon as the changes are made.)
Note that the AQ-EC1 gain switch displays -3, 0 and 9 correspond to L, M and H, and the
OUTPUT switch settings CAMERA, TEST and BAR to CAM/AUTO KNEE ON, CAM/AUTO
KNEE OFF and BAR for each main unit.
The Synchro scan and Super V modes cannot be used while the AQ-EC1 is connected to the
unit.
The lens iris (IRIS) control of the AQ-EC1 is valid only when the lens iris AUTO/MANUAL selec-
tor is set to AUTO.
-46- 
						

							Warning/Status Displays in the Viewfinder and Display Window
Displaying the Setting Menu Inside the Viewfinder
When the MENU SET/OFF switch is set to SET, the setting menu appears on the viewfinder
screen. The setting menu is displayed in page units. The following table lists all pages contained
in the setting menu as well as an outline of the functions for each page.
The setting menu configuration can be changed according to the purpose.
Setting Menu Configuration
Page
No.Page name
58
MARKER
56VF DISPLAY
59CAMERA ID
72SHUTTER SPEED
73SYNCHRO SCAN
52! LED
81SET UP CARD
107MAIN FUNCTION
108-110FUNCTION 1/5 to 5/5
62TIME DATE
64SETTING LOW/MID/
HIGH
115-119LEVEL 1/6 to 6/6
120VF OPERATION
121LENS ADJ
121-123 MENU SELECT 1/3 to3/3
124AUTO SHADING
50DATA RESET
124 124
DIAGNOSTIC
Function outline
Marker settings
Selection of viewfinder screen
displays
Camera ID display settings
Shutter speed/mode settings
Synchro scan shutter speed
settings
! lamp display settings
Setup card Used function settings
Used function settings
Time and date settings Camera settings
Camera settings
Viewfinder operations Lens adjustments
User menu ON/OFF settings
Automatic shading adjustments Resetting the setting menu
Reference
Setting the MarkerDisplays
Setting Display Items
Setting the Camera ID Display
Setting the Electronic Shutter
Setting the
Electronic Shutter
Setting the ! Lamp Display
Setup card
operations
Selecting Functions
Selecting Functions
Selecting Functions
Recording
Adjustments
Viewfinder
Lens
User Menu
Shading Returning to the
default settings
See the corresponding pages for a detailed description of each page ’s functions.

When connecting the AQ-EC1 extension control unit (option) and controlling the AJ-D700 exter-
nally, the engineer menu is always opened as the setting menu.
-47
- 
						

							Warning/Status Displays in the Viewfinder and Display Window
Changing the setting menu configuration
The setting menu can be configured by selecting only the pages necessary for the application.
Pages are selected using the MENU SELECT page of the engineer menu mode.
When using the engineer menu, switch the unit to engineer mode as described below.
The unit is switched to user mode by setting the MENU SET/OFF switch to “SET”.
The unit is switched to engineer mode by holding down the SHIFT/ITEM and UP buttons simulta-
neously and setting the MENU SET/OFF switch to SET.
The user and engineer modes differ as follows.
User mode:Only the selected pages the setting menu can be used. The data set on each
page is written to the non-volatile memory, allowing it to be stored for extended
periods of time.
Engineer mode: All pages contained in the setting menu can be used. In addition, the data set at
each page is written to the non-volatile memory, allowing it to be stored for ex-
tended periods of time.
After completing the adjustments and settings with engineer mode, configuring a menu consisting
only of frequently used pages allows the necessary pages to be called quickly.
- 48 - 
						

							Basic Setting Menu Operations
The setting menu is operated using the MENU SET/OFF switch and the SHIFT/ITEM, UP, DOWN
and PAGE buttons.
SHIFT/ITEM Switch
UP Button
DOWN Button
PAGE Button
MENU SET/OFF Switch
Displaying the setting menu
1Set the MENU SET/OFF switch to SET.
The status displays at the top and bottom of the viewfinder screen disappear, and the page
on which the previous setting menu operations were completed appears.
When the menu is used for the first time, the first of the selected pages appears.
- MARKER -
CENTER MARK : ON
SAFETY ZONE : 1
Changing the page
1Press the PAGE button.
The menu page changes each time the PAGE button is pressed.
- ! LED -
*GAIN(0dB)
·GAIN(-3dB)
*SHUTTER·WHITE PRESET*EXTENDER·FILTER
·SUPER V
The page can also be changed using the UP and DOWN buttons as follows.
PAGE+UP:The menu page is incremented continuously while the UP and PAGE buttons
are held down.
PAGE+DOWN: The menu page is decremented continuously while the DOWN and PAGE
buttons are held down.
- 49 - 
						

							Warning/Status Displays in the Viewfinder and Display Window
Selecting the desired item
1Press the SHIFT/ITEM switch.
Each time this button is pressed, the cursor (arrow) which indicates the selected item moves
to the next item.
Cursor
Movement order
– MARKER –
CENTER MARK : ON
SAFETY ZONE : 1
The item can also be selected using the UP and DOWN buttons as follows.
Changing the settings
Press the UP button to increase the setting.
The setting is incremented by 1 level each time
the UP button is pressed.
Press the DOWN button to decrease the setting.
The setting is decremented by 1 level each time
the DOWN button is pressed.
Changing the ON/OFF selection
The setting switches to ON or OFF each time the UP (or DOWN) button is pressed.
Returning to the default settings
The unit can be returned to the default settings (the settings when shipped from the factory or the
engineer mode settings) by pressing the UP (or DOWN) button at the DATA RESET page of engi-
neer mode*.
However, care should be taken as the flare and shading adjustment values cannot be returned to
the default settings.
Quitting the menu
Set the MENU SET/OFF switch to OFF.
The setting menu disappears from the viewfinder screen and the displays indicating the units
current status appear at the top and bottom of the viewfinder screen.
*Engineer mode
The menu for this mode is opened by holding down the SHIFT/ITEM and UP buttons simulta-
neously and then setting the MENU SET/OFF switch to the “SET” position.
- 50 -