Panasonic Aj D700 Operating Instructions Manual

							Replacing the Backup Battery
The unit is shipped from the factory with a backup battery already mounted. When the battery runs
out, the TCG time code value indicates 00:00:00:00.
At this time, the time code value cannot be backed up.
In addition, the “BACK UP BATT EMPTY” display appears in the viewfinder for 3 seconds when
the POWER switch is set to ON to indicate that the battery must be replaced.
Consult your dealer when replacing the battery.
Backup Battery
-101- 
						

							Setting Menu Screens 
						

							VF DISPLAY Screen
This page sets the setting for the display information inside the viewfinder.
Item– VF DISPLAY –
DISP MODE :3
EXTENDER :ON
SHUTTER :ON
TAPE :ON
BATTERY:ONFILTER:ONWHITE:ONGAIN:ONLEVEL METER:ON
IRIS :S+IRI S
CAMERA ID
:ON
Menu screen display methods
USER menu: Setting the MENU
switch to SET displays the USERmenu.
ENG menu:Holding down the
SHIFT/ITEM and UP
buttons
simultaneously and
setting the MENU
switch to SET
displays the ENG menu. DISP MODE
EXTENDER
SHUTTER
TAPE BATTERYFILTER
WHITE
GAIN
LEVEL METER
IRIS
CAMERA ID
Variable range
1–3
VF
display
USER
ENG
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
IRISS+IRIS
S
OFF USER
ENG
USER
ENG
USER
ENG
USER
ENG
USER
ENG
USER
ENG
USER
ENG
USER
ENG
USER
ENG
ON
USER
OFF ENG
Remarks
Change Display1 2 3
FILTER
GAIN
AWB
AUTO KNEE
SW
SHUTTER
ABB STATUS
AWB STATUS
Extender display ON/OFF
Shutter speed display ON/OFF
Remaining tape length display ON/OFF
Battery voltage display ON/OFF Filter No. display ON/OFF
AWB PRE/A/B display ON/OFF Currently selected gain display ON/OFF
Audio level meter display ON/OFF
IRIS:Only the f-number is displayed.
S+IRIS:Both the super iris ON status
and f-number are displayed.
S:Only the super iris ON status
is displayed.
OFF: Neither the super iris ON
status nor f-number is
displayed.
Mix ON/OFF during color bar recording
The underlined setting in the Variable range column indicates the preset mode.
-103 - 
						

							Setting Menu Screens
CAMERA ID Screen
This page performs the camera ID settings. Each time the UP button is pressed, the character display changes in the orde\
r ofspace, English letters (A to Z), numbers (0 to 9) and symbols [space, >, 
						

							SYNCHRO SCAN Screen
This page performs the synchro scan settings.
– SYNCHRO SCAN –
1/61.7
Item
SYNCHRO
SCAN
Variable VF
rangedisplay Remarks
1/30.4
1/61.7
1/250
USER
ENG
Synchro shutter speed selection
! LED Screen
This page sets the ON/OFF setting for the ! LED display inside the viewfinder. The ON/OFF status for each item is indica\
ted by
displaying an asterisk (*) or period (.) in front of the item on the screen.
– !LED –
* GAIN(0dB )
. GAIN(–3dB)
*
SHUTTER. WHITE PRESET
*
EXTENDER. FILTE R
. SUPER V
range
* : ON
.: OFF
Item
GAIN (0 dB)
GAIN (–3 db)
SHUTTER
WHITE PRESET EXTENDER
FILTER
SUPER V
Variable
ON
OFF
ONOFF
ON
OFF
ONOFF
ON
OFF
ONOFF
ONOFF
VF
display
ENG
ENG
ENG
ENG ENG
ENG
ENG
Remarks
This selects whether or not the LED is lighted when the gain is any value other
than 0 dB.
This selects whether or not the LED islighted when the gain is any value other
than –3 dB.
This selects whether or not the LED islighted when the shutter is ON.
This selects whether or not the LED is lighted when the AWB CH is PRESET.
This selects whether or not the LED is lighted when the lens is in EXTENDER
mode.
This selects whether or not the LED is lighted when the filter is any value other
than 3200K.
This selects whether or not the LED is lighted when SUPER V is ON.
The ! LED lights when both GAIN (0 dB) and GAIN (–3 dB) are ON unless the gain is set to
–3 dB or 0 dB.
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:
Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays the
ENG menu.
- 105 - 
						

							Setting Menu Screens
SET UP CARD Screen
This page sets the loading, saving and formatting operations for setup cards. Align the “–” with the desired item and press the
UP or DOWN button to perform the corresponding processing.
– SET UP CARD –
READ ( CAM)
WRITE ( CARD)
CARD CONFIG.
ID READ/WRITE :ON
FUNCTION1~2R/W:ON
L/M/H SET R/W :ON
LEVEL 1~6 R/W :ONItem
READ( CAM)
WRITE
( CARD)
CARD CONFIG.
ID READ/WRITE
FUNC1~2 R/W
L/M/H SET R/W
LEVEL1~6 R/W
Variable
range
ON
OFF
VF
display
USER
ENG
USER
ENG
USER
ENG
USER
ENG
ON
USER
OFF
ENG
ON
OFFUSERENG
ON
OFFUSERENG
Remarks
Setup card data is written to the unit.
Camera data is written to the setup
card.
The setup card is formatted.
CAMERA ID READ/WRITE is switched
ON or OFF when data is read from or
written on the set-up card.
ON:Read/write is enabled.
OFF:Read/write is disabled.
READ/WRITE for FUNCTION1 and
FUNCTION2 is switched ON or OFF
when data is read from or written on the
set-up card.
ON:Read/write is enabled.
OFF:Read/write is disabled.
READ/WRITE for LOW SETTING, MID
SETTING and HIGH SETTING is
switched ON or OFF when data is read
from or written on the set-up card.
ON:Read/write is enabled.
OFF:Read/write is disabled.
READ/WRITE for LEVEL 1/6,2/6,3/6,
4/6, 5/6 and 6/6 is switched ON or OFF
when data is read from or written on the
set-up card.
ON:Read/write is enabled.
OFF:Read/write is disabled.
*For example, so as not to change the CAMERA ID when reading from, or writing to the SET UP CARD, the ID READ/WRITE
should be selected to OFF.
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays the
ENG menu.
-106- 
						

							MAIN FUNCTION Screen 
						

							Setting Menu Screens
FUNCTION 1/5 Screen
This page performs the adjustment function 1 settings. The ON/OFF status for each item is indicated by displaying an ast\
erix (*)or period (.) in front of the item on the screen.
– FUNCTION 1/5 –Item
*DETAIL
*2D LPF
SKIN TONE DTL
*MATRIX
*GAMMATEST SAW
*FLARE
DETAIL
2D LPF
SKIN TONE DTL
*: ON
·:OFFMATRIX
GAMMA
TEST SAW
FLARE
FUNCTION 2/5 Screen
This page performs the adjustment function 2 settings.
– FUNCTION 2/5 –
SUPER V
: FRM1FILTER INH :OFFSHOCKLESS AWB:NORMALS. IRIS SW :S. IRIS
S. SCAN SEL:ON
Item
SUPER V
FILTER INH
SHOCKLESS
AWB
S.IRIS SWS.SCAN SEL
Variable range
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Variablerange
OFF
FRM1
FRM2
ONOFF
OFF
NORMAL
SLOWFAST
S.IRIS 30 dBOFF
ON
OFF
VF
display
ENG
Remarks
Detail (H, V) ON/OFF switching
ENGON/OFF switching for 2-dimensional LPF (Low Pass Filter) which reduces
color smear
ENGSkin tone detail ON/OFF switching
ENG
ENGColor adjustment ON/OFF switching Gamma circuit ON/OFF switching
ENGTest signal ON/OFF switching
ENGFlare compensation ON/OFF switching
VF
display
ENG
Remarks
Super V ON/OFF switching
FRM1: Normal mode FRM2: Lag reduction mode
ENGSwitch that determines whether AWB
memory (Ach, Bch) data is stored for
each filter. ON: Ach and Bch memory only
(2 memory units), regardless of
the filter.
OFF: Data is stored for each filter.
(4x2=8 memory units)
ENGShockless AWB ON (NORMAL/SLOW/
FAST)/OFF switching
ENGSuper iris (SIRIS)/30dB/OFF
switching
ENGSynchro scan ON/OFF switching
ON: S.SCAN speed can be varied
by the SUPER IRIS/MODE
CHECK switch.
OFF: Normal mode
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:
Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays the
ENG menu.
-108 - 
						

							FUNCTION 3/5 Screen 
						

							Setting Menu Screens