Panasonic Aj D650 Operating Instructions Manual

USER menu
ItemSetting
No.SuperimposedNo.SuperimposedDescription
displaydisplay
300 VAR0000– 0.43 – 1This sets the VAR speed range.
RANGE0001– 4 – +40: The tape is played in slow motion at a speed ranging from
– 0.43× to +1× normal speed.
1: The tape is played in the ±4.1× normal speed range.

Phase synchronization from the editing controller is no longer
possible once this item has been set to “0”.
For DV format:
When using the dial on the front panel, playback is always
performed at – 0.5 to +1× normal...

USER menu (continued)
ItemSetting
Description
This sets the channel assignments for the controller’s analog
audio preset when editing the digital audio of the VTR using a
controller which does not have a digital audio edit preset
control function.
This selects the channel concerned when the VTR CUE edit
preset is set in compliance with the ON or OFF presetting for
the analog audio signals designated by the editor or
controller.
0:  Not set.
1:  Compliance with analog CH1 edit preset.
2:  Compliance with...

Setup (setting) menus
USER menu

Item Setting
No.Superimposed No. SuperimposedDescription
displaydisplay
5 0 0 VITC000010LThis sets the position where the VITC signal is to be inserted.
POS-1000111L(The same line as for VITC POS-2 in 501 cannot be
0002 12Lselected.)
000313L
0004 14L
000515L
000616L
000717L
000818L
000919L
0010 20L
501VITC000010LThis sets the position where the VITC signal is to be inserted.
POS-2000111L(The same line as for VITC POS-1 in 500 cannot be
0002 12Lselected.)
000313L
0004 14L...

USER menu
 (continued)
ItemSetting
Superimposed
displaySuperimposed
displayDescription
This selects whether to control the phase correction of the
LTC generated by the TCG.
0: Phase correction control is not performed.
1: Phase correction control is performed.
This selects whether the CF flag of the TCG is to ON.
0: CF flag is OFF.
1: CF flag is ON.
This selects the DF/NDF mode for CTL and TCG.
0: Drop frame mode.
1: Non-drop frame mode.
No.509 is valid when the CONTROL is LOCAL or LOCAL
ENA of item 004...

Setup (setting) menus
USER menu (continued)
ItemSetting
No.SuperimposedNo. SuperimposedDescription
displaydisplay
604 V-MUTE0000N-MUTEThis selects whether the video output signal is to be muted in
SEL0001LOW-RFthe event of a low RF or disengaged servo lock during
playback.
0: No muting (picture freezes).
1: Muting (picture turns grey).
605 CC (F1) 0000
BLANK
0001
BLANKThis selects ON or OFF for the closed capture signal in the
THRUfirst field.
0: Forced blanking performed.
1: Blanking not performed....

USER menu

ItemSetting
No.SuperimposedNo. SuperimposedDescription
displaydisplay
700 CH1 IN
00004dBThis selects the audio input (CH1) reference level switching.
LV
00010dB
0002
-20dB
0003-60dB
701 CH2 IN
00004dBThis selects the audio input (CH2) reference level switching.
LV
00010dB
0002-20dB
0003-60dB
703CH1 OUT0000 4dBThis selects the audio output (CH1) reference level switching.
LV
00010dB
0002
-20dB
704CH2 OUT0000 4dBThis selects the audio output (CH2) reference level switching.
LV
00010dB
0002...

USER menu
 (continued)
ItemSetting
No.SuperimposedNo.Superimposed
display
716REC CUE 0000
0001
0002
Description
display
CH1This selects the input signal recorded in CUE.
CH20: The signal selected by SETUP-MENU No.714 is recorded
CH1+2on CH1.1:The signal selected by SETUP-MENU No.715 is recorded
on CH2.2: The signal selected by SETUP-MENU No.714 and
No.715 are mixed and recorded on CH1 and CH2.
718 DV
OUTPUT
0000
0001
0002
ST1This selects the AUDIO CH1 and CH2 output signals during
ST2DV format playback....

Time code/user bit
Time code
The time code is used when the time code signal generated by the time code generator
(time code signal generator) is to be recorded on the tape, its values are to be read by the
time code reader (time code signal reader), and the absolute position of the tape is to be
displayed in increments of hours, minutes, seconds and frames.
The time code is written in the sub-code area (data area) of the helical track. This enables
insert editing to be conducted independently using the...

Recording internal/external time codes
 Setting the internal time code
Place the VTR in the stop mode.
Set the CTL/TC/UB switch to TC.
Set the TC lNT/EXT switch to INT. (Internal time code selected)
Set the RUN MODE. (setup menu No. 510)
REC (RUN):The time code runs at the same time as the recording proceeds.
FREE (RUN): The time code runs in the same way as the time regardless of the
VTR’s operation.
Set the REGEN MODE. (setup menu No. 504)
OFF (REGEN): Continuity is maintained with the recorded time...

Reproducing the time code/user bit
Place the unit in the stop mode.
Set the CTL/TC/UB switch to TC or UB.
TC: The time code is displayed.
UB: The user bit is displayed.
• When it is no longer possible to read the time code, it is interpolated using the
CTL signal.
Press the PLAY button.
Playback now commences, and the time code appears on the display.
When setting menu No.006 (SUPER) is ON, the time code value is superimposed onto
the video signal from the VIDEO OUT 3 connector.

• The colon between the...