Panasonic Air Conditioner S 26pk2u6__cv6233320526 Operating Instructions

							11
WIRELESS REMOTE CONTROLLER
UNIT DISPLAY AND OPERATION CONTROLLER
OPERATION lampThis lamp lights when the appliance is turned on.
TIMER lampThis lamp lights when the system is being controlled by the timer.
STANDBY lampWhen the unit is in the heating standby condition, the STANDBY lamp lights. If the unit is used for 
cooling only, the STANDBY lamp will not illuminate. This lamp operates only when an alarm occurs.
Remote control receiverThis section picks up infrared signals from the wireless remote controller (transmitter).
Emergency Operation
buttonYou can operate this air conditioner using the operation controller without the wireless remote 
controller.
TIMER OPERATION
STANDBY
STANDBY lampTIMER lamp
OPERATION lamp
Emergency Operation buttonReceiver
85464609338010_02_EN.fm  Page 11  Wednesday, September 2, 2015  12:10 PM 
						

							12
USING WIRELESS REMOTE CONTROLLER
How to Install Batteries 1.Press and slide the cover on the back of the wireless remote controller in the direction of the 
arrow.
2.Install two AAA alkaline batteries (LR03). Make sure the batteries point in the direction marked 
in the battery compartment.
3.Press the reset hole, then replace the cover. If you press it, the current time, ON time, and OFF 
time are all reset to 0:00.
• The batteries last about six months, depending on how much you use the wireless 
remote controller. Replace the batteries when the wireless remote controller’s lamp fails 
to light, or when the wireless remote controller cannot be used to change the air 
conditioner’s setting. 
• Use two fresh leak-proof type-AAA alkaline batteries (LR03).
• In replacing batteries, follow the instructions as mentioned in the sub-section “How to 
Install Batteries”. 
• If you do not use the wireless remote controller more than 1 month, take out the 
batteries.
Reset hole
Cover
Information for Users on Collection and Disposal of Old Equipment and used Batteries
[Information on Disposal in other Countries 
outside the European Union]
These symbols are only valid in the European 
Union. If you wish to discard these items, 
please contact your local authorities or dealer 
and ask for the correct method of disposal.Note for the battery symbol (bottom two 
symbol examples):
This symbol might be used in combination with 
a chemical symbol. In this case it complies with 
the requirement set by the Directive for the 
chemical involved. 
85464609338010_02_EN.fm  Page 12  Wednesday, September 2, 2015  12:10 PM 
						

							13
USING WIRELESS REMOTE CONTROLLER (CONTINUED)
How to Use Wireless
Remote ControllerWhen using the wireless remote controller, always point the unit’s transmitter head directly at 
the air conditioner’s receiver.
Wireless Remote
Controller Installation
PositionThe wireless remote controller can be operated from either a non-fixed position or a wall-
mounted position. To ensure that the air conditioner operates correctly, do not install the 
wireless remote controller in the following places:
 In direct sunlight
 Behind a curtain or other place where it is covered
 More than 19 ft. (6 m) away from the air conditioner
 In the path of the air conditioner’s air stream
 Where it may become extremely hot or cold
 Where it may be subject to electrical or magnetic interference
1.If Non-fixed Position
Raise the rear plate of the remote controller mounting cradle and insert the wireless remote 
controller.
The unit can be used either in that position (placed on a table, for instance) or held in the 
hand.
2.If Wall-mounted Fixed Position
Install the wireless remote controller at a convenient location on a nearby wall. However, 
before attaching the wireless remote controller mounting cradle, check that the wireless 
remote controller can operate from the desired wall position.
Air conditioner
(Transmitter head)
Wireless remote controllerReceiver
Wireless Remote 
Controller
Remote Controller 
mounting cradleRear plate
12
Press
Put in
Fasten the Remote Controller 
mounting cradle with screws.
Remote Controller mounting cradleFitting the Remote 
Controller in the mount.
85464609338010_02_EN.fm  Page 13  Wednesday, September 2, 2015  12:10 PM 
						

							14
REMOTE CONTROLLER
1. Operation DisplayDisplays the operation status. 
(The figure shows all the statuses.)
 The auto-flap display may be 
different, depending on the 
installed unit.
2. Start/Stop 
button Pressing this button once starts and 
pressing again stops the operation.
3. Fan speed 
button
4. Swing/Wind 
Direction 
button
5. Timer setting 
buttonUse for operating with a timer.
6. Reset buttonUse this button after changing the 
batteries.
7. CoverPress at the top center and then slide 
down.
8. Transmitter
9. Remote control 
sensorDetects the temperature at the 
remote controller when detection has 
been switched to the remote 
controller by the sensor button.
10. Temperature setting 
buttonsraises the temperature setting 
1.8°F (1°C) at a time.
lowers the temperature setting 
1.8°F (1°C) at a time.
11. Filter button CZ-RWSC3
Press to turn off the filter lamp on the 
receiver.
12. Mode Select 
buttonPress to switch the operation mode.
13. Ventilation 
buttonUse this when connected to an 
aftermarket fan. Pressing this button 
starts and stops the fan. When the air 
conditioner is started or stopped, the 
fan starts or stops at the same time. 
(  appears on the display of the 
remote controller when the fan is 
operating.)
14. Address 
button15. Sensor buttonUse this when switching to detect the 
temperature at the remote controller. 
At shipping the default setting is set 
to detect the temperature at the unit. 
At this time   is shown on the 
display.
16. Clock buttonUse this when setting the clock.
From this page on the names of remote control 
buttons will be abbreviated as the illustration of the 
“button”. 
E.g.: Start/Stop button       
1
2
3
4
5
6
78
9
10
11
12
13
14
15
16
85464609338010_02_EN.fm  Page 14  Wednesday, September 2, 2015  12:10 PM 
						

							15
HOW TO SET ADDRESS (  )
Setting addresses of indoor units for remote controller
Setting Remote Control Addresses
1. If you press   and   at the same time, “SET” will blink.
2. While holding   down, every time you press  , it cycles from ALL   1   2   3… 6   ALL.
Set it to the receiver address switch of the indoor unit you wish to operate.
3. When you release  , the address that was displayed is set.
When you do this, if it corresponds to the receiver’s address setting, the buzzer sounds.
Setting Addresses
(Setting the address of the indoor unit)
1. First of all, set the address for the remote controller with Setting Remote Control Address.
2. Press [Emergency Operation]   button of the indoor unit for four seconds or more.
When you do this, the lamps of the display will blink one after another.
3. Press   on the remote controller.
4. The buzzer will sound and the address of the indoor unit will change to the address displayed on the remote controller.
5. If you press [Emergency Operation]   button of the indoor unit once, the lamps on the indoor unit’s display will turn off.
 Please do not hold the [Emergency Operation]  button of the indoor unit down while the indoor unit’s display lamps are blinking one 
after another.
 Make sure to operate while the indoor unit is stopped.
 The address of indoor unit is set to ALL at the time of the shipment.
Address 
Display on the 
Remote 
Controller
NOTE
85464609338010_02_EN.fm  Page 15  Wednesday, September 2, 2015  12:10 PM 
						

							16
OPERATION
Setting Current Time
After changing the batteries and pressing reset, be sure to reset the current time. 
(When reset is pressed, the current time reverts to [  ])
1. Press  for two seconds or more.
Once the clock displays starts blinking, the clock can be set.
2. Set the hour with  /  of the  .
If you press and hold the button, the time changes quickly.
3. Set the minutes with  /  of the  .
If you press and hold the button, the time changes quickly.
4. Pressing  completes the time setting.
 While you are setting the current time, the t ime display flashes but the colon does not.
 If the buttons are not pressed for three minutes while setting the current time, it is set to the 
displayed time.
When reset is pressed, the timer settings are deleted.
Operation
Auto  , Heat  , Dry  , Cool  , Fan   
Models that only provide the cooling function cannot operate in the auto or heating modes.
Power: Turn on the power of the indoor unit at least 14 hours before operation.
1. Press
 .
2. Press   and select from among Auto  , Heat  , Dry  , Cool   and Fan  .
3. Press   and select the desired speed.
If set to Auto
 , the fan speed switches automatically.
(Auto does not work when in the Fan mode.)
4. Press one of the   buttons and set the desired temperature.
Temperature settings cannot be made when in the Fan mode.
°F (°C)
Stop: Press
 .
When the unit is stopped with the remote controller, even though the compressor of the 
outdoor unit stops, the fan on the outdoor unit may continue to run for a while.
If the unit is not heating very effectively with a Low fan speed  , switch the fan speed to High   or   Medium.
Depending on the indoor unit being used, it may indicate a function that it does not have. (The fan speed is set.)
If you cannot turn the air conditioner off in the normal way.
Disconnect the power to the indoor unit and contact the dealer where the product was purchased. Auto Heat Dry / Cool 
MAX 80 (27) 78 (26) 86 (30)
MIN 62 (17) 60 (16) 64 (18)
231, 4
NOTE
2 31
4
85464609338010_02_EN.fm  Page 16  Wednesday, September 2, 2015  12:10 PM 
						

							17

If all the indoor units are identical in a cooling system and are under control as one group, it 
heats or cools automatically via the differences between the set temperature and the room 
temperature.

 Depending on the indoor unit used, the remote controller may have a [Dry]  indicator on its 
display even though the unit does not have the Dry function. 
(Same as cooler operation)
 When the room temperature approaches the temperature setting, the unit continues to start 
up or stop automatically.
 When the drying mode stops operating, the indoor unit’s fan blows a gentle breeze in order to 
keep the moisture from returning to the room at a minimum.
 Depending on the indoor unit used, and/or the temperature in the room, the fan speed may not 
be adjustable.
 Depending on the unit used, when the outside air temperature is 59 °F or less, the dry function 
will not operate.

 When setting the timer, make sure the current time on the remote controller is accurate.
 The timer’s clock can only be set when the display of the remote controller is ON.
 After setting the timer, put the remote controller in a place where its signal will reach the 
receiver of the indoor unit. (When the time set for the timer is reached, a signal is sent from 
the remote controller to Start/Stop the unit.)
„Using the Timer
When the drying mode stops operating, the indoor unit’s fan blows a gentle breeze in order to 
keep
1. Press either  /  of the   or  , and while the time is being displayed, 
if you press  /  again, a scheduled time can be set.
The time last set on the timer is displayed.
“--:--“ indicates time to change the batteries.
2. Press either  /  of the   or   and set the timer to the desired time.
Every time you press   /   , the time changes in 10 minute increments.
If you press and hold the button, the time changes quickly.
3. After setting the timer, if you press  , the time you set changes to a steady
display, indicating settings are complete.
After the timer setting is displayed for three seconds, the display reverts to the current 
time.
2 31
4
3
1, 2
85464609338010_02_EN.fm  Page 17  Wednesday, September 2, 2015  12:10 PM 
						

							18
„Combining ON and OFF Timers
 Setting the ON and OFF timers, respectively.
„Checking the timer setting
 If you press either   /   for the   or the  , the scheduled time is displayed for four seconds.
 When no timer setting has been made, it displays --:--. (Initial Setting)
„Changing a timer setting
 Press   /   for the   or the  , and then when the timer setting is displayed, press    /   for the timer again.
„Canceling a timer setting
 If you press [CANCEL], the timer setting is canceled.
 If you wish to cancel the setting for either the   or the   timer, press   /   or the desired timer and when the scheduled time is 
displayed, press [CANCEL].
„Using the same timer setting every day
 If you press  for 2 or more seconds, “ ” is displayed and the ON timer or the OFF timer will operate the unit at the same time 
every day.
 If you press
  again for two seconds or more, “ ” goes off and the timer operates just once.
85464609338010_02_EN.fm  Page 18  Wednesday, September 2, 2015  12:10 PM 
						

							19
Adjusting Wind Direction
 Never try to manually move the flap (up-down wind direction plate) that is operated by the remote controller.
 When the unit stops, the flap (up-down wind direction plate) automatically faces downwards.
 When the unit is in heating standby, the flap (up-down wind direction plate) faces upward.
Also, bear in mind that the flap starts swinging after the heating standby mode is released, but the display on the remote controller 
indicates Auto Flap during standby heating as well.
Setting Wind Direction
While the unit is operating, every time you press  , the direction the flap 
faces changes.
Setting Flap to Swing
If you press   to set the flap (up-down wind direction plate) in its most 
downward facing position, and then press   again,    is displayed and 
the flap swings automatically up and down.
Stopping Flap Swing
If you press   again while the flap is swinging, you can stop the flap from 
swinging and set it in place as desired. Thereafter, if you press   , you can 
set the wind direction starting from the most upward position.
When the unit is in the Cool or Dry modes, the flap cannot stop facing 
downwards. If you try to stop the flap from swinging while it is facing 
downwards, it will continue moving until it is in the third position from the top.
Operating Multiple In/Outdoor Units Simultaneously (Group Control)
Group control works well for providing air conditioning to 
one, large room with more than one air conditioning units.
 One remote controller can operate up to eight indoor units.
 All the indoor units have identical settings.
 Set temperature sensing to the indoor unit (Main Sensor).
Please face the flap (up-down wind 
direction plate) downwards. If it faces 
upwards, the warm air will not reach 
the floor level.
In the Heat Mode
Pleaseface the flap (up-down wind 
direction plate) upwards.If the plate 
faces downwards, condensation 
may form and drip from around 
the air outlet.
In the Cool and Dry Modes
In the Fan Mode In All Modes
Displays with Swing Stopped
Initial Setting
Initial Setting
Initial Setting
Moves Constantly
Fan/Heat Modes
Cool/Dry Modes
Wireless Remote ControllerSignal Line Indoor UnitIndoor Unit
Receiver
85464609338010_02_EN.fm  Page 19  Wednesday, September 2, 2015  12:10 PM 
						

							20
OPERATION WITHOUT WIRELESS 
REMOTE CONTROLLER
STEP 1 To start the air conditioner
Press [Emergency Operation] 
 button of the 
indoor unit.
STEP 2 To stop the air conditioner
Press [Emergency Operation] 
 button of the 
indoor unit.
TIMER OPERATION
STANDBY
Emergency Operation button
85464609338010_02_EN.fm  Page 20  Wednesday, September 2, 2015  12:10 PM