Panasonic Air Conditioner S 26pk2u6 Operating Instructions

11
WIRELESS REMOTE CONTROLLER
UNIT DISPLAY AND OPERATION CONTROLLER
OPERATION lampThis lamp lights when the appliance is turned on.
TIMER lampThis lamp lights when the system is being controlled by the timer.
STANDBY lampWhen the unit is in the heating standby condition, the STANDBY lamp lights. If the unit is used for 
cooling only, the STANDBY lamp will not illuminate. This lamp operates only when an alarm occurs.
Remote control receiverThis section picks up infrared signals from the wireless remote...

12
USING WIRELESS REMOTE CONTROLLER
How to Install Batteries 1.Press and slide the cover on the back of the wireless remote controller in the direction of the 
arrow.
2.Install two AAA alkaline batteries (LR03). Make sure the batteries point in the direction marked 
in the battery compartment.
3.Press the reset hole, then replace the cover. If you press it, the current time, ON time, and OFF 
time are all reset to 0:00.
• The batteries last about six months, depending on how much you use the wireless...

13
USING WIRELESS REMOTE CONTROLLER (CONTINUED)
How to Use Wireless
Remote ControllerWhen using the wireless remote controller, always point the unit’s transmitter head directly at 
the air conditioner’s receiver.
Wireless Remote
Controller Installation
PositionThe wireless remote controller can be operated from either a non-fixed position or a wall-
mounted position. To ensure that the air conditioner operates correctly, do not install the 
wireless remote controller in the following places:
 In direct...

14
REMOTE CONTROLLER
1. Operation DisplayDisplays the operation status. 
(The figure shows all the statuses.)
 The auto-flap display may be 
different, depending on the 
installed unit.
2. Start/Stop 
button Pressing this button once starts and 
pressing again stops the operation.
3. Fan speed 
button
4. Swing/Wind 
Direction 
button
5. Timer setting 
buttonUse for operating with a timer.
6. Reset buttonUse this button after changing the 
batteries.
7. CoverPress at the top center and then slide 
down....

15
HOW TO SET ADDRESS (  )
Setting addresses of indoor units for remote controller
Setting Remote Control Addresses
1. If you press   and   at the same time, “SET” will blink.
2. While holding   down, every time you press  , it cycles from ALL   1   2   3… 6   ALL.
Set it to the receiver address switch of the indoor unit you wish to operate.
3. When you release  , the address that was displayed is set.
When you do this, if it corresponds to the receiver’s address setting, the buzzer sounds.
Setting...

16
OPERATION
Setting Current Time
After changing the batteries and pressing reset, be sure to reset the current time. 
(When reset is pressed, the current time reverts to [  ])
1. Press  for two seconds or more.
Once the clock displays starts blinking, the clock can be set.
2. Set the hour with  /  of the  .
If you press and hold the button, the time changes quickly.
3. Set the minutes with  /  of the  .
If you press and hold the button, the time changes quickly.
4. Pressing  completes the time setting....

17

If all the indoor units are identical in a cooling system and are under control as one group, it 
heats or cools automatically via the differences between the set temperature and the room 
temperature.

 Depending on the indoor unit used, the remote controller may have a [Dry]  indicator on its 
display even though the unit does not have the Dry function. 
(Same as cooler operation)
 When the room temperature approaches the temperature setting, the unit continues to start 
up or stop automatically....

18
„Combining ON and OFF Timers
 Setting the ON and OFF timers, respectively.
„Checking the timer setting
 If you press either   /   for the   or the  , the scheduled time is displayed for four seconds.
 When no timer setting has been made, it displays --:--. (Initial Setting)
„Changing a timer setting
 Press   /   for the   or the  , and then when the timer setting is displayed, press    /   for the timer again.
„Canceling a timer setting
 If you press [CANCEL], the timer setting is canceled.
 If you...

19
Adjusting Wind Direction
 Never try to manually move the flap (up-down wind direction plate) that is operated by the remote controller.
 When the unit stops, the flap (up-down wind direction plate) automatically faces downwards.
 When the unit is in heating standby, the flap (up-down wind direction plate) faces upward.
Also, bear in mind that the flap starts swinging after the heating standby mode is released, but the display on the remote controller 
indicates Auto Flap during standby heating as...

20
OPERATION WITHOUT WIRELESS 
REMOTE CONTROLLER
STEP 1 To start the air conditioner
Press [Emergency Operation] 
 button of the 
indoor unit.
STEP 2 To stop the air conditioner
Press [Emergency Operation] 
 button of the 
indoor unit.
TIMER OPERATION
STANDBY
Emergency Operation button
85464609338010_02_EN.fm  Page 20  Wednesday, September 2, 2015  12:10 PM