Panasonic A47 Dome Camera Quick Start Guide

Network Mini Dome Camera·Quick Operation Guide  10 No.8 is the audio/alarm cable interface, of which the “I” mark connects to the alarm input, the “o” mark connects to the alarm output, the “GND” mark connects the grounding, and the “A” mark connects the audio output.   WPS (Wi-Fi Protected Setup, also known as AOSS or QSS) is a computing standard that attempts to allow easy establishment of a secure wireless network. Refer to user manual for details.  A wireless router with the WPS function is...

Network Mini Dome Camera·Quick Operation Guide  112 Installation Before you start:  Make sure the device in the package is in good condition and all the assembly parts are included.  Make sure all the related equipment is power-off during the installation.  Check the specification of the products for the installation environment.  Make sure the power supply is matched with your required voltage to avoid damage.  If the product does not function properly, please contact your dealer or the nearest...

Network Mini Dome Camera·Quick Operation Guide  12● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection.  ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly.  2.1 Ceiling Mounting Steps: 1. Drill the screw holes and the...

Network Mini Dome Camera·Quick Operation Guide  13A different type of drill template might be provided because of the different batches of products. And also, the contained adapter plate matches with type II drill template differs as well. See figure below.  Figure 2-2 Type II Drill Template  2. Loosen the set screw on the front cover to disassemble the camera with the supplied Allen key.  Figure 2-3 Disassemble the Camera Drill TemplateA11Hole A :for cables routed through the wallScrew hole1 :for...

Network Mini Dome Camera·Quick Operation Guide  143. Fix the adapter plate to the ceiling with the supplied expansion screws.  Figure 2-4 Fix the Adapter Plate  If the supplied drill template is type II drill template, you can just skip step 3 and go straight to step 4.  4. Fix the dome drive with the supplied screws.  Figure 2-5 Fix the Dome Drive Adapter PlateSide Outlet 

Network Mini Dome Camera·Quick Operation Guide  155. Connect the power cable, network cable, and the audio/alarm cables.  Use a plier to remove the removable part and route the cables via side outlet (as shown in Figure 2-4) if no cable hole is drilled in step 1, and connect the corresponding cables.  Figure 2-6 Remove the Removable Part 6. View the image via the web browser. 7. Slightly loosen the hex screw beside the WPS/RESET button to adjust the surveillance angle. 8. Use the supplied adjusting tool...

Network Mini Dome Camera·Quick Operation Guide  16 Figure 2-7 3-Axis Adjustment 9. Tighten the hex screw to fix the well-adjusted surveillance angle. 10. Align the front cover to the dome drive and tighten the set screws on the front cover.  Figure 2-8 Install the Front Cover Adjusting ToolRotationTiltPan 

Network Mini Dome Camera·Quick Operation Guide  1711. Tear off the protection film softly to complete the installation.   Do not tear off the protection film until the installation is completed.  Do not touch the inside face of the bubble with your hands. 2.2 Ceiling Mounting with a Gang Box Steps: 1. Fix the adapter plate to the gang box with the supplied PM4X8 screws.  Figure 2-9 Fix the Adapter Plate 2. Fix the dome drive to the adapter plate with the supplied PM4X8 screws.  

Network Mini Dome Camera·Quick Operation Guide  18 Figure 2-10 Fix the Dome Drive 3. Connect the power cable, network cable, and the alarm/audio cables. 4. Align the front cover to the dome drive and tighten the set screws on the front cover.  Figure 2-11 Install the Front Cover  

Network Mini Dome Camera·Quick Operation Guide  195. Tear off the protection film softly to complete the installation.   Do not tear off the protection film until the installation is completed.  Do not touch the inside face of the bubble with your hands. 2.3 Ceiling Bracket Mounting Steps: 1. Install the bracket to the ceiling with the supplied screws in the ceiling bracket package.  The matched ceiling bracket model is DS-1271ZJ-120, and you need to purchases it separately if ceiling bracket mounting...