Panasonic A14 And A34 Dome Camera Quick Start Guide

							Network Dome Camera Quick Operation Guide  10 Installation Before you start:  Please make sure that the device in the package is in good condition and all the assembly parts are included.  Make sure that all the related equipment is power-off during the installation.  Check the specification of the products for the installation environment.  Make sure the power supply is matched with your required voltage to avoid damage.  If the product does not function properly, please contact your dealer or the nearest service center. Do not disassemble the camera for repair or maintenance by yourself.  Please make sure that the wall is strong enough to withstand three times the weight of the camera. Steps:  Drill the cable hole and the screw holes in the ceiling according to the supplied drilling template.   Figure 2-1 Drilling Template Screw HoleScrew HoleScrew HoleCeiling Mounting 
						

							Network Dome Camera Quick Operation Guide  11 Loosen the set screws with a hex key (supplied) to remove the bubble.               Figure 2-2 Remove the Bubble  Connect the corresponding cables.  If required, you can route cables through the side opening on the side of the mounting base.  Figure 2-3 Side Opening Side Opening 
						

							Network Dome Camera Quick Operation Guide  12 Fix the mounting base to the ceiling with screws. Figure 2-4 Fix the Mounting Base  Adjust the surveillance angel.  Loosen the tilt adjusting screws, and adjust the tilt angel [0~65], and tighten the tilt adjusting screws.  Hold the black liner and rotate it to adjust the pan position [0~360].  Remove the black liner and rotate the camera to adjust the azimuth angle [0~360].  Figure 2-5 3-axis Adjustment Tilt Adjusting Screw 
						

							Network Dome Camera Quick Operation Guide  13 As the lens has already been factory adjusted to the best imaging effect, you just need to adjust the pan position and tilt position to get the desired surveillance angle.  Reinstall the bubble and tighten the screws.  Figure 2-6 Complete the Installation  
						

							Network Dome Camera Quick Operation Guide  14 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then install the iVMS-4200 software to search and change the IP address of the network camera. The following figure shows the cable connection of a network camera and a PC:  Figure 3-1 Wiring over LAN  Set the IP address of the camera for accessing via LAN. Steps: To set the IP address, please use the Advidia Camera Finder Utility as described below:  To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the Advidia Camera Finder Utility. Refer to the following introductions to set IP address with the Advidia Camera Finder Utility software (for more detailed instructions please  
						

							Network Dome Camera Quick Operation Guide  15download the Camera Finder manual from the Advidia Website www.advidia.com/support):  After launching the Advidia Camera Finder software, it automatically searches the online devices from the subnet where your computer is located.  This search may take 30 seconds or more depending on network size. After searching it will show total number and information of the Advidia cameras found on the network. Device information including the device type, IP address, port number, gateway, etc. will be displayed.  Figure 3-2 Advidia Camera Finder Note: To perform a manual search for additional cameras: Click the refresh icon  to refresh the online device list manually. The newly discovered devices will be added to the list. Note:  
						

							Network Dome Camera Quick Operation Guide  16You can click on each column heading to order the information.  Modify device information Steps: 1). Select the device(s) to be modified in the device list as shown in Figure 3-3.  2). Click on “File” and select “Login Manager” as shown in Figure 3-4 to enter the username and password information of selected device(s). 3). Enter the username and password information of the admin account of each device you wish to modify in the “Username” and “Password” fields and click the Save icon  to save the changes. 4). Close the Login Manager and select “Launch Edit Table” under the “Edit” menu dropdown or with Ctrl+E as seen in figure 3-5.  Figure 3-3 Select a Device       
						

							Network Dome Camera Quick Operation Guide  17Figure 3-4 Login Manager   Figure 3-5 Launch Edit Table   Figure 3-6 Edit Table 5) Enter the desired IP address (or range if changing the IP address of more than one device) of the network camera in the address field of the edit table  
						

							Network Dome Camera Quick Operation Guide  18and click Apply Network Changes. You can also select “Dynamic IP” if you would prefer to have an IP address assigned by your network router.   The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”. For security purposes the default Username and password should be changed to something unique.  For accessing the network camera from different subnets, please set the gateway for the network camera after you log in.  
						

							Network Dome Camera Quick Operation Guide  194 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above version Steps: 1) Open the web browser. 2) In the browser address bar, input the IP address of the network camera, e.g., 192.0.0.64 and press the Enter key to enter the login interface. 3) Input the user name and password. 4) Click Login.