Panasonic 42"50" Class 720p Plasma Hdtv Tc P42x1 Operating Instructions

							TM
Quick Start Guide
(See page 8-18)
Guía de inicio rápido
 (vea la página 8-18)
TQB2AA0806
Operating Instructions
42”/50” Class 720p Plasma HDTV
(41.6/49.9  inches measured diagonally)
Manual de instrucciones
Televisión de alta definición de 720p y clase 42”/50” de Plas\
ma
(41,6/49,9 pulgadas medidas diagonalmente)
Model No.
Número de modeloTC-P42X1
TC-P50X1
English
Español
Lea estas instrucciones antes de utilizar su televisor y guárdelas pa\
ra consultarlas en el futuro.
Las imágenes mostradas en este manual tienen solamente fines ilustrat\
ivos.
  For assistance (U.S.A./Puerto Rico), please call:
  1-877-95-VIERA (958-4372)
  or visit us at www.panasonic.com/contactinfo 
  For assistance (Canada), please call:
 1-866-330-0014
  or visit us at www.vieraconcierge.ca
  Para solicitar ayuda (EE.UU./Puerto Rico), llame al:
 1-877-95-VIERA (958-4372)
  ó visítenos en www.panasonic.com/contactinfo 
Please read these instructions before operating your set and retain them\
 for future reference.
The images shown in this manual are for illustrative purposes only. 
						

							2
HDMI, the HDMI logo and High-
Definition Multimedia Interface are 
trademarks or registered trademarks of  HDMI Licensing LLC.VIERA Link™ is a trademark of Panasonic Corporation.SDHC Logo is a trademark.
HDAVI Control™ is a trademark of  Panasonic Corporation. Manufactured under license from Dolby 
Laboratories.
Dolby and the double-D symbol are  trademarks of Dolby Laboratories.
Turn your own living room into a movie theater!
Experience an amazing level of multimedia excitement
DIGITAL TELEVISION TRANSITION NOTICE
This device contains a digital television tuner, so it should receive digital over the air TV programming, with a suitable 
antenna, after the end of full-power analog TV broadcasting in the United States (as required by law) on February \
17, 
2009.  Some older television receivers, if they rely on a TV antenna, will need a TV Converter to receive over the air digital 
programming, but should continue to work as before for other purposes (\
e.g., for watching low-power TV stations still 
broadcasting in analog, watching pre-recorded movies, or playing video g\
ames). When a Converter is used with an older 
television receiver, a signal splitter might be necessary to continue to receive low-power \
analog broadcasts via an antenna. 
For more information, please see www.DTV.gov. For information on the TV Converter program, and on government 
coupons that may be used toward the purchase of one, see www.dtv2009.gov, or call the NTIA at 1-888-DTV-2009. Please 
check with your cable or satellite service provider if you have question\
s about your cable or satellite set-top box. 
						

							3
Viewing
Advanced
FAQs, etc.
Quick Start Guide
This product qualifies for ENERGY STAR 
in the “Home” setting and this is the setting 
in which energy savings will be achieved. 
Any modifications to the “Home” setting or 
other factory default settings could result in 
greater energy consumption beyond levels 
that meet ENERGY STAR qualifications.
 Watching TV  ··················\
··················\
··········· 19 Using VIERA TOOLS ··················\
··············· 21  Viewing from an SD Card ··················\
········ 22  Watching Videos and DVDs ··················\
····· 24
  How to Use Menu Functions 
(picture, sound quality, etc.) ··················\
····· 26
 VIERA LinkTM “HDAVI ControlTM” ················ 30 Lock ··················\
··················\
··················\
····· 36  Editing and Setting Channels···········\
·········· 38 Closed Caption ··················\
··················\
······ 40 Input Labels ··················\
··················\
··········· 41 Using Timer ··················\
··················\
············ 42 Recommended AV Connections ················ 43
  Ratings List for Lock ··················\
················ 44 Technical Information ··················\
··············· 45  Care and Cleaning ··················\
··················\
· 49 FAQ ··················\
··················\
··················\
······ 50 Specifications ··················\
··················\
········· 52 Limited Warranty (for U.S.A. and Puerto Rico only)··········\
····· 53
  Customer Services Directory (for U.S.A. and Puerto Rico) ··················\
···· 54
  Limited Warranty (for Canada) ··················\
· 55
Enjoy your TV!
Basic Features
Advanced Features
FAQs, etc.
 Safety Precautions ··················\
··················\
··· 4 Notes ··················\
··················\
··················\
······ 7
Please read before using the unit
 Accessories/Optional Accessory  ····· 8
 Basic  Connection ··················\
··········11
 Identifying  Controls ··················\
······ 15
 First Time  Setup··················\
··········· 16
Quick Start Guide
Enjoy rich multimedia
SD memory card
Camcorder
Amplifier
Home theater 
system VCR
DVD recorder/
Blu-ray Disc recorder Set Top Box
DVD player/
Blu-ray Disc player
Contents 
						

							4
Safety Precautions
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatu\
s to rain or moisture.Do not place liquid containers (flower vase, cups, cosmetics, etc.) ab\
ove the set
(including on shelves above, etc.).
Important Safety Instructions
1)    Read these instructions.
2)     Keep these instructions.
3)     Heed all warnings.
4)     Follow all instructions.
5)     Do not use this apparatus near water.
6)     Clean only with dry cloth.
7)      Do not block any ventilation openings. Install in 
accordance with the manufacturer’s instructions.
8)     Do not install near any heat sources such as radiators, 
heat registers, stoves, or other apparatus (including 
amplifiers) that produce heat.
9)      Do not defeat the safety purpose of the polarized or 
grounding-type plug. A polarized plug has two blades with 
one wider than the other. A grounding type plug has two 
blades and a third grounding prong. The wide blade or the 
third prong are provided for your safety. If the provided 
plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.
10)    Protect the power cord from being walked on or pinched 
particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus. 11) 
  Only use attachments / accessories specified by the 
manufacturer.
12)    Use only with the cart, stand, tripod, 
bracket, or table specified by the 
manufacturer, or sold with the 
apparatus. When a cart is used, 
use caution when moving the cart / 
apparatus combination to avoid injury 
from tip-over.
13)    Unplug this apparatus during lightning storms or when 
unused for long periods of time.
14)    Refer all servicing to qualified service personnel. Servicing 
is required when the apparatus has been damaged in any 
way, such as power-supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped.
15)    To prevent electric shock, ensure the grounding pin on the 
AC cord power plug is securely connected.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a\
n Other Class B digital device, pursuant to Part 15 of the 
FCC Rules. These limits are designed to provide reasonable protection against harmf\
ul interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy an\
d, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. Ho\
wever, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful\
 interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by o\
ne or more of the 
following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the Panasonic Service Center or an experienced radio/TV tec\
hnician for help.
FCC Caution:
To assure continued compliance, follow the attached installation instruct\
ions and use only shielded interface cables 
when connecting to peripheral devices. Any changes or modifications not expressly approved by Panasonic Corp. o\
f 
North America could void the user’s authority to operate this device.
Responsible Party: Panasonic Corporation of North AmericaOne Panasonic Way, Secaucus, NJ 07094
Contact Source: Panasonic Consumer Electronics Company1-877-95-VIERA (958-4372)
email: [email protected]
CANADIAN NOTICE:
For Model TC-P42X1,  TC-P50X1
This Class B digital apparatus complies with Canadian ICES-003.
  
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
  
WARNING: To reduce the risk of electric shock, do not remove cover or back.
No user-serviceable parts inside. Refer servicing to qualified service p\
ersonnel.
The lightning flash with 
arrowhead within a triangle is 
intended to tell the user that 
parts inside the product are a 
risk of electric shock to persons.
The exclamation point within 
a triangle is intended to 
tell the user that important 
operating and servicing 
instructions are in the 
papers with the appliance. 
						

							5
  WARNING
Small parts can present choking hazard if accidentally 
swallowed.
Keep small parts away from young children.
Discard unneeded small parts and other objects, including 
packaging materials and plastic bags/sheets to prevent 
them from being played with by young children, creating 
the potential risk of suffocation.
 Set up  This Plasma TV may fall and can cause personal injury or even death if not installed correctly. To prevent personal injury 
or death, follow these warnings:
  Install the Plasma TV in accordance with the  manufacturer’s recommended pedestal or stand, 
corresponding hardware and installation instructions.
  This Plasma TV is for use only with the following optional  accessories. Use with any other type of optional accessories 
may cause instability. The following accessories are 
manufactured by Panasonic Corporation.
  • Wall-hanging bracket (Angled)  TY-WK4P1RW
  Be sure to ask a qualified technician to carry out the installation and set-up.
  Two or more people are required to install or remove the  television.
  Some wall mounts (wall-hanging brackets) are not  designed to be mounted to walls with steel studs or old 
cinder block constructions.
  Ask your dealer or licensed contractor to properly secure the  wall-hanging bracket.
  Do not place the Plasma TV or its stand on a sloped or  unstable surface.
  The Plasma TV may fall or tip over.
  Do not support the Plasma TV on a non-specified pedestal.
  Do not place the Plasma TV on furniture that can easily  be used as steps, such as a chest of drawers.
  Do not climb or allow children to climb on the Plasma TV  Place or install the Plasma TV where it cannot be pushed, pulled over or knocked down.
  Route all cords and cables such that they cannot be  tripped over or pulled by curious children.
  Do not place any objects on top of the Plasma TV.
  If water spills onto the Plasma TV or foreign objects get  inside it, a short-circuit may occur which could result in fire 
or electric shock. If any foreign objects get inside the Plasma 
TV, please consult an Authorized Service Center.
 AC Power Supply CordTo prevent fire or electric shock:  The Plasma TV is designed to operate on a 120 V AC, 60 Hz service. Insert the power cord plug as far as it will 
go into the wall socket.
  If the plug  is not fully inserted, heat may generate, which  could cause a fire.
  The included power cord is for use with this unit only.
  Do not use any power cord other than that provided with  this TV.
  Do not handle the power cord plug with wet hands.
  Do not do anything that might damage the power supply  cord.
  When disconnecting the power supply cord, hold the plug, not the cord.
  Do not use the power supply cord if the plug or cord is  damaged.
  Replace the cord or contact your Authorized Service Center
 Handling the power supply cord Insert the power plug fully into the socket outlet. (If the 
power plug is loose, it could generate heat and cause fire.)
  Ensure that the power plug is easily accessible.  Ensure the earth pin on the power plug is securely connected to prevent electrical shock.
 •  
An apparatus with CLASS I construction shall be connected to 
a power socket outlet with a protective earthing connection.
  Do not touch the power plug with a wet hand. (This may  cause electrical shock.)
  Do not use any power cord other than that provided with this TV. (This may cause fire or electrical shock.)
  Do not damage the power cord. (A damaged cord may  cause fire or electrical shock.)
 •  Do not move the TV with the cord plugged in the socket outlet. •   Do not place a heavy object on the cord or place the cord 
near a high-temperature object.
 •   Do not twist the cord, bend it excessively, or stretch it.
 •   Do not pull on the cord. Hold onto the power plug body 
when disconnecting cord.
 •   Do not use a damaged power plug or socket outlet.
 If Problems Occur During Use  If a problem occurs (such as no picture or no sound), 
or if smoke or an abnormal odor is detected from the 
Plasma TV, unplug the power supply cord immediately.
  Continued use of the TV under these conditions might cause  a fire or permanent damage to the TV. Have the TV evaluated 
by an Authorized Service Center. Servicing of the TV by 
unauthorized personnel is strongly discouraged due to its 
high voltage.
  If water or an object get inside the Plasma TV, if the Plasma TV is dropped, or if the enclosure becomes 
damaged, unplug the power supply cord immediately.
  A short-circuit may occur, which could cause a fire. Contact  an Authorized Service Center for an evaluation.
  CAUTION
  Do not cover the ventilation holes.  Doing so may cause the Plasma TV to overheat, which can cause a fire or damage to the Plasma TV.
  Leave a space of 3 15/16” (10 cm) or more at the top, left and right, and 2 3/4” (7 cm) or more at the rear. 
  When using the pedestal, keep the space between the  bottom of the TV and the pedestal or stand surface clear 
from objects that may obstruct ventilation.
 When Moving the Plasma TV  Be sure to disconnect all cables before moving the Plasma TV.
  Moving the TV with its cables attached might damage the  cables which, in turn, can cause fire or electric shock
  To prevent an electric shock, disconnect the power  plug from the wall outlet as a safety precaution before 
carrying out any cleaning.
WARNING/CAUTION 
						

							6
     
CEA CHILD SAFETY NOTICES:  Flat panel displays are not always supported on the proper stands or
installed according to the manufacturer’s recommendations.  Flat panel displays that are inappropriately
situated on dressers, bookcases, shelves, desks, speakers, chests or carts may fall over and may cause
personal injury or even death.
The consumer electronics industry (of which Panasonic is a member) is committed to making home
entertainment enjoyable and safe. To prevent personal injury or death, be sure to follow the following safety
guideline:
TUNE INTO SAFETY:
•One size does NOT fit all. Follow the manufacturer’s recommendations for the safe installation and use
of your flat panel display.
• Carefully read and understand all enclosed instructions for proper use of this product.
• Don’t allow children to climb on or play with furniture and television sets.
• Don’t place flat panel displays on furniture that can easily be used as steps, such as a chest of drawers.
• Remember that children can become excited while watching a program, especially on a “larger than life”
flat panel displays.  Care should be taken to install the display where it cannot be pushed, pulled over,
or knocked down.
• Care should be taken to route all cords and cables connected to the flat panel display so that they
cannot be pulled or grabbed by curious children.
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS:
• Use a mount that has been recommended by the display manufacturer and/or listed by an independent
laboratory (such as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount manufacturers.
• If you have any doubts about your ability to safely install your flat panel display, contact your retailer
about professional installation.
• Make sure the wall where you are mounting the display is appropriate.  Some wall mounts are not
designed to be mounted to walls with steel studs or old cinder block construction.  If you are unsure,
contact a professional installer.
• A minimum of two people are required for installation.  Flat panel displays can be heavy.
Panasonic recommends that a qualified installer perform the wall-mount
installation.  See page 5.
Safety Precautions (Continued)
  Transport only in upright position  Transporting the unit with its display panel facing upright or 
downward may cause damage to the internal circuitry.
  Using a dry cloth, clean any dust from the power supply  cord and plug regularly.
  Build-up of dust on the power cord plug can increase  humidity, which might damage the insulation and cause a fire.
This Plasma TV radiates infrared rays; 
  therefore, it may affect other infrared communication  equipment. Install your infrared sensor in a place away from 
direct or reflected light from your Plasma TV.
The TV will still consume some power as long as the power 
supply cord is connected to the wall outlet.   Display panel is made of glass. Do not apply strong force 
or impact to the display panel.
  This may cause damage resulting in injury.
  The TV is heavy. TV should be handled by 2 or more people. Support as shown to avoid injury by the TV 
tipping or falling.
  
						

							7
 Do not display a still picture for a long timeThis causes the image to remain on the plasma screen
(“Image retention”). This is not considered a malfunction and is not covered by the warranty.
4 : 312To prevent “Image retention”, the screen saver is 
automatically activated after a few minutes if no signals are 
sent or no operations are performed. (p. 51)
Typical still images
• Channel number and other logos
• Image displayed in 4:3 mode
• SD Card photo     • Video game     • Computer image
■ Set up Do not place the unit where it’s exposed to sunlight or other bright light (including reflections). Use of some types of fluorescent lighting may reduce the remote control’\
s transmission range.
Notes 
						

							8
Accessories/Optional Accessory
Accessories
Check you have all the items shown.
Remote Control
Transmitter
 N2QAYB000321
Batteries for the
Remote Control
Transmitter (2)
 AA Battery
AC cordPedestal TBLX0088 
(TC-P42X1)
 TBLX0089 (TC-P50X1)
Product Registration Card (U.S.A.)
Customer Care Plan Card (U.S.A.)
Operating Instructions
Quick Setup Guide 
Installing the remote’s batteries
Open
Hook
Note the correct polarity
(+ or -).
Close
Caution
 Incorrect installation may cause battery 
leakage and corrosion, resulting in damage 
to the remote control.
 •  Do not mix old and new batteries.
 •  Do not mix different battery types (such 
as alkaline and manganese batteries).
 •  Do not use rechargeable (Ni-Cd) batteries. Do not burn or break batteries.
Optional Accessory
Note
 In order to maintain the TV’s performance and safety, be absolutely sure  to ask your dealer or a licensed contractor to secure the wall-hanging 
brackets.
 Carefully read the instructions accompanying the plasma TV stand or pedestal, and be absolutely sure to take steps to prevent the TV from 
tipping over.
 Handle the TV carefully during installation since subjecting it to impact or other forces may cause its panel to crack.
Wall-hanging bracket(angle) TY-WK4P1RW
Accessories
How to assemble (p. 9)Cleaning cloth 
						

							9
Quick Start Guide
 Accessories/Optional Accessory
Accessories
Assembly screws 
(4 of each)
 
A
M5 x 18 (Silver)
B
M5 x 25 (Black)
Poles (2)
LR
  L or R is printed at the 
bottom of the poles.
 Base (1)
Attaching the pedestal to TV
■Assembling the pedestal
  Fix securely with assembly screws A. (Total 4 screws)
  Tighten screws firmly.
 
A
L
RPole
Front
Pole
Base
■Set-up
  Carry out work on a horizontal and level surface.
  Tighten screws firmly.
B
 Fix securely with assembly screws B. 
(Total 4 screws)
Rear side
Arrow 
mark
Pole Hole for pedestal 
installation 
Pole
 Base 
Bottom view
Warning
Do not disassemble or modify the pedestal.
 Otherwise the TV may fall over and become damaged, and personal injury may result.
Caution
Do not use any other TV and displays.
 Otherwise the TV may fall over and become damaged, and personal injury may result.
Do not use the pedestal if it becomes warped or physically damaged.
 If you use the pedestal when it is physically damaged, personal injury m\
ay result. Contact your nearest Panasonic  Dealer immediately.
During set-up, make sure that all screws are securely tightened.
 If sufficient care is not taken to ensure screws are properly tightened during\
 assembly, the pedestal will not be  strong enough to support the TV, and it might fall over and become damaged, and personal injury may res\
ult. 
						

							10
Accessories/Optional Accessory (Continued)
AC cord connection
Antenna terminal Pin terminalsHDMI terminal
greenbluered
green
 Firmly tighten by hand. Match colors of plugs and terminals. Insert firmly. Insert firmly.
Reference of connection
To attach To remove
Insert it firmly until the 
tabs on both sides click 
into place. Keep pushing both 
side snaps and pull 
down