Panasonic 42"50"55"60"65" Class 1080p Plasma Hdtv Tc P42s60 Owners Manual

							11
 Attaching the pedestal to TV
Assembly screws (black)BracketNeckBase
(7) (for 42/50)
(12) (for 55/60/65)
M5 × 16
Assembly screws (black)
(4) (for 42/50)
M4 × 10
Attaching the pedestal
5
3
1
2
4
TC-P42S60
TC-P50S60 TC-P55S60
TC-P60S60
TC-P65S60
A
A
C
D
E
A
B(for 55/60/65)
(for 42/50)
Removing the pedestal from the TVBe sure to remove the pedestal in the following way when using 
the wall-hanging bracket or repacking the TV.  
  Remove the assembly screws  (for 55/60/65) /  (for 42/50) from the TV. Lift the TV from the pedestal.  Remove the assembly screws  from the bracket.  Remove the assembly screws  from the bottom of the 
base and pull out the neck.
Warning
Do not disassemble or modify the pedestal.
 Otherwise, the TV may fall over and become damaged, and personal injury may result.
Caution
Do not use any pedestal other than that provided with this TV.
 Otherwise, the TV may fall over and become damaged, and personal injury may result.Do not use the pedestal if it becomes warped or physically damaged. If you use the pedestal when it is physically damaged, personal injury m\
ay result. Contact your 
nearest Panasonic Dealer immediately.
During set-up, make sure that all screws are securely tightened.
 If sufficient care is not taken to ensure screws are properly tightened during\
 assembly, the pedestal 
will not be strong enough to support the TV, and it might fall over and become damaged, and personal 
injury may result.
When removing the pedestal, do not remove the pedestal by any methods ot\
her than the specified 
procedure. (Above)
 Otherwise, the TV and/or pedestal may fall over and become damaged, and personal injury\
 may 
result. 
						

							12
 Installing the remote’s batteries
Pull open
Hook
Note the correct 
polarity (+ or -). Close
Caution
 Incorrect installation may cause battery 
leakage and corrosion, resulting in 
damage to the remote control.
• Do not mix old and new batteries.
• Do not mix different battery types (such 
as alkaline and manganese batteries).
• Do not use rechargeable (Ni-Cd) batteries.
 Do not burn or break batteries.
Attaching Ferrite Core
(For TC-P42S60/TC-P50S60 only)
Be sure to attach the provided ferrite core to the HDMI cable/USB cable \
of Keyboard (not supplied) to 
reduce interference or electrical noise.
Attach the ferrite core as close as possible to connector on the TV side\
 as shown.
(for HDMI cable)
(for USB cable of keyboard)
Close the ferrite core until it clicks.
(for HDMI cable)
(for USB cable of keyboard) 
						

							13
 Connections
Connection Panels
 
●For , ,  connections, 
please refer to p. 15
Back of the TV
USB1/2 
terminal
Ethernet
connector
Digital audio out 
						

							14
Power Cord
Connect after all other 
connections have been 
made.Back of the TV
Cable TV
VHF/UHF Antenna
or
  Antenna or Cable connection
VHF/UHF Antenna•  NTSC (National Television System Committee): Analog television system
ATSC (Advanced Television Systems Committee):
Digital TV Standards include digital high-definition television (HDTV), standa\
rd-definition television (SDTV), 
data broadcasting, multi-channel surround sound audio and interactive te\
levision.
 Cable 
●You need to subscribe to a cable TV service to enjoy viewing their programming. 
●A high-definition connection can be made using an HDMI or Component Video cable. (p. 15)
Note
 
●When using a Cable box, external equipment and video cables shown in thi\
s manual are not supplied 
with the TV.
 
●For additional assistance, visit us at:   www.panasonic.com/help
www.panasonic.ca
Insert it firmly until the tabs on 
both sides click into place. Keep pushing both sides 
until they snap and pull.
To attach
To remove 
						

							15
  AV cable connection
Best
Good
Basic
(Not HD)
  To use  HDMI terminals (Set-top-box / DVD recorder / Blu-ray Disc player / Camcorder / etc.)
L
R
HDMI
AV OUT
HDMI cable
DVI OUT
AUDIO OUTe.g. Blu-ray Disc 
player
e.g. Blu-ray Disc 
player
AV Equipment
AV Equipment
Audio cable
white white
red
red
HDMI-DVI 
Conversion cable
 To use  COMPONENT terminals (DVD recorder / Blu-ray Disc player / etc.)
L
R Y
P
B
PR
AUDIO
OUT
COMPONENT
VIDEO OUT
white red
green
bluered
e.g. Blu-ray Disc 
player
AV Equipment
white
red blue green
whitered red
blue
green
red
  To use  COMPOSITE terminals (Camcorder / Game system / DVD recorder / etc.)
e.g. CamcorderAV Equipment
L
RCOMPOSITE
OUT
yellow
white red
yellow
white red
white
red yellow
Note
 
●In some cases, it is not possible to connect depending on the type of ca\
ble or 
equipment.
 
●The Green terminal is shared for both the COMPONENT and COMPOSITE (VIDEO IN) 
connection. When using COMPOSITE (VIDEO IN) connection, the Yellow connector 
(Video) should be inserted into Green connection. 
						

							16
  Audio connection
HDMI cableHDMI OUT
    (ARC)
Optical cable
DIGITAL 
AUDIO INe.g. Amplifier with
speaker system
HDMI connection is available if connected audio equipment has ARC (Audio Return Channel) function.
  Please refer to eHELP (p. 20) for Network connection, VIERA link connection or other connections.
Panasonic does not guarantee operation and performance of peripheral dev\
ices made by other 
manufacturers; and we disclaim any liability or damage arising from oper\
ation and/or performance 
from usage of such other maker’s peripheral devices. 
						

							17
Identifying Controls
TV controls/indicators
Note
  The TV consumes a small amount of electric energy even when turned off.  Do not place any objects between the TV remote control sensor and remote control.
•  An image of the control panel is displayed on the screen while in use.
C.A.T.S. (Contrast Automatic Tracking System)
 Power indicator ( on: red, off: no light)
Front of the TV
Remote control sensor
Maximum range for remote is 23 feet (7 meters) 
from front of TV set
Back of the TV
(42/50)
Volume up/down Selects channels 
in sequence
POWER button Changes the input mode
Selects Menu and Submenu entries
(Press and hold down for MENU function)
(55/60/65) 
						

							18
 Remote control
Switches TV On or Off (Standby) Viewing from external media Closed caption On/Off
Switches surround sound setting
Displays Main Menu
Displays or removes the 
information banner
Displays VIERA TOOLS menu
Displays Option Menu for special 
functions (when available)
 Colored buttons 
(used for various functions) Sound mute On/Off
 Volume up/down
Use for digital channels
Accesses NETFLIX service directly 
(via Online movies screen)
•  This service requires an Internet  connection.
•  This service might be stopped or the  conditions changed without notice.
Operates the Favorite channel list functionChanges aspect ratio and zoom
Selects Secondary Audio Programming
 Exits from menu screen
Displays Online movies screen
Select source to watch
Selects/OK/Change
Go back to previous menu
Channel up/down, when viewing from 
ANT/Cable source
Numeric keypad to select any channel or 
press to enter alphanumeric input in menus
 Switches to previously viewed 
channel or input
External equipment operations
*  Functions are switched depending on 
connected external equipment and 
operation.
:  Press and hold to skip 
backward/forwardSet Sleep timer
Displays eHELP (built-in manual) 
(p. 20) 
						

							19
First Time Setup
The first time setup screen is displayed only when the TV is turned on for the first time, after 
the power cord is inserted into a wall outlet.
(42/50)
(55/60/65)
Turn the TV on with the POWER button
or
(Remote)
(TV)
Setup the following items
 
●Select your language
 
●Select your country
 
●Select your viewing mode (Be sure to select “Home Use”)If you select “Store Demonstration” by mistake, confirmation scree\
n 
will be displayed.
To display the “Set viewing mode” screen again in order to select “Home Use”, perform one of the following actions:
•  Press and hold down the rear POWER button for at least five  seconds.
•  Unplug the power cord for 30 seconds and then plug it in again.
 
●Configure Network connection
Follow the instructions on screen to complete the Network 
connection.
 
●ANT/Cable setup
Select and adjust the settings according to your ANT/Cable 
environment. Select “Yes” on the confirmation screen to start 
the scanning process. After scanning is complete, press OK to 
continue.
 
●Adjust the Clock
Select the clock mode and adjust other settings.
When “Auto” is selected, clock will be set automatically according\
 
to Time zone and DST. The TV must be connected to the Internet to 
use this feature.
 
●Complete First time setup
Completion screen is displayed.
To watch TV via a Cable box, Satellite receiver, or any other source 
(DVD, DVR, gaming device, etc.), press the INPUT button and select the 
appropriate input.  
						

							20
Display eHELP[Top page]When you enter 
eHELP again 
after exiting, the 
confirmation screen 
is displayed while the 
TV is turned on.
You can select “TOP 
PAGE” or “LAST 
PAGE”.
Select the desired page from the menu
 Next
 Select
 Next
 Select
 Next(If available)
Scroll up/down
(If available the scroll 
bar appears.)
Submenus Desired pageCategories Menus
 Select
   To exit 
eHELP
  To return to 
the previous 
menu/layer
 
■Jump to menu item
Display the menu related to the explanation page.
 
●The menu is not available depending on situation or condition.
Using eHELP (Built-in Manual)
eHELP is a built-in manual that explains how to easily operate the TVs features. Press the 
eHELP button to access the guide.