Panasonic 2k Processor Ajhdp2000 Operating Instructions

							11
2K Processor & HD-D5 VTR System Connections
Digital (AES/EBU) Audio input
HD Reference input
Dual-Link SDI Input
Dual-Link SDI output
Dual-Link SDI output
Single HD SDI Monitor output
Digital (AES/EBU) Audio output
Analog Audio output
Cue Audio output
Timecode output
Waveform output Analog Audio input
HD SYNC OUT
Cue Audio input
Timecode inputDIGITAL AUDIO IN ch1 - 8
AUDIO IN ch1 - 4
CUE IN
TC IN
DIGITAL AUDIO OUT ch1 - 8
AUDIO OUT ch1 - 4
CUE OUT
TC OUT
WFM OUT
RS-422 Control input
RS-422 Control output
RS-422 Control in/output
RS-232C control
Parallel 50-pin control
From Control Panel I/FREMOTE IN (RS-422)
REMOTE OUT (RS-422)
REMOTE IN/OUT (RS-422)
RS-232C
PARALLEL IN/OUT (50P)
CONTROL PANEL HD REF  IN
(REF loop through)
INPUT  A
MON INPUT  B
OUTPUT  1A
OUTPUT  1B
OUTPUT  2A
OUTPUT  2B
REF IN  HD
SERIAL DATA IN
HD SDI  OUT
SERIAL DATA OUT
HD SDI  IN
2K Processor
HD-D5 VTR
Note:  Be Sure to Connect Three I/Os for 2K Processor Systems as below
HD SYNC OUT REF IN  HD
SERIAL DATA IN HD SDI  OUT
SERIAL DATA OUT HD SDI  IN
2K Processor AJ-HD3700B/A/H 
						

							12
Connection with existing systems
This is an example where the connections for the existing system and the 2K system are switched within the router.
To switch to the 2K system mode, select “2048 (PsF)” or “1920 (PsF)” in F3 (VIDEO) in SYSTEM SET UP menu on 
the HD-D5 VTR.
For details, refer to pages 9 and 10 of the “Operating Instructions Supplement” for the AJ-HD3700H, AJ-HD3700A, 
and AJ-HD3700B.
Server/Color Corrector/Telecine
HD House Reference Signal
HD/SD Player/Recorder
HD analog Signal Router
HD-D5 VTRs   
(AJ-HD3700H, AJ-HD3700A, AJ-HD3700B)
2K Processor (AJ-HDP2000)
HD SDI Signal Router 2048/1920 4:4:4
Dual-Link SDI Signals2K SYSTEM connection
Existing SYSTEM connection 
						

							13
Indicator Display (Front Panel LED)
The operating state of this unit can be checked on the three LEDs (Alarm Lamp, Horizontal Sample 
Display Lamps) on the front panel: Lighting or Blinking.
Display Description
Normal operating state
(Lighting: When there is no warning or when the warnings are masked from 
MENU)
Format error
(In the following cases, 1920 LED or 2048 LED blinks normally or rapidly.)

RECORDED FORMAT UNMATCH (NO J2K TAPE):
TAPE is not 2K processor recording format.

RECORDED FORMAT UNMATCH:
There is a mismatch between SYSTEM FORMAT of the unit selected in 
settings and FORMAT of TAPE. (2048/1920, XYZ/RGB)
UNMATCH H SAMPLE BETWEEN INPUT SIGNAL AND SYSTEM:
There is a mismatch in H SAMPLE between the SYSTEM set value and the 
input signal.
Other errors
(ALARM Lighting or Blinking: In the case of a warning corresponding to an alarm 
indication)

2K FAN STOP:  The fan of the 2K processor stops.
2K NO REMOTE:  The service switch on the back of the 2K processor is not in
the OFF position.

CRC ERROR IN SERIAL DATA INPUT FROM HDD5:
A CRC error occurs in SERIAL DATA (HD SDI) signals from the HD-D5 
VTR main unit to the 2K processor.
OUT OF RANGE OF SYSTEM PHASE BETWEEN REF AND INPUT:
There is a large phase difference between the input signal and REF IN.
INPUT SIGNAL UNMATCH SYSTEM FREQUENCY:
There is a mismatch in frame frequency between the SYSTEM set value 
and the input signal.
SUBSTANDARD TIMING DIFFERENCE IN DUAL LINK 2K INPUT:
The timing-phase difference of Dual-Link IN A/Bch is big.
CRC ERROR IN DUAL LINK CHA 2K INPUT:
A CRC error occurs in signals on Dual-Link IN Ach.
CRC ERROR IN DUAL LINK CHB 2K INPUT:
A CRC error occurs in signals on Dual-Link IN Bch.
NO EXTERNAL HD_REFERENCE:
HD REF IN on the HD-D5 VTR is not connected.
(Although this is the existing warning for the HD-D5 VTR, the ALARM LED 
of the 2K Processor also blinks.)
or
or
or(Lighiting or Blinking) 
						

							14
Connection Check
After the regular system is connected, it is possible to 
check which devices are connected to each other by 
executing CONNECTION CHECK in the Front Panel 
MENU of the HD-D5 VTR when you own more than 
one unit of the 2K Processor and HD-D5 VTR.All three LEDs of “ALARM”, “2048” and “1920” 
repeatedly blink during the operation described on the 
left. (For the regular system connection)
Service Switch (Rear)

Service Switch (only Use Service Maintenance)
This slide switch is only for service mode.
Please make sure slide OFF for Normal Operation.
Power On
For the power supply to each unit, construct 2K 
SYSTEM and then turn on the power to the 2K 
Processor, before turning on the power to the HD-D5 
VTR.
SERVICEON
OFF 
						

							15
Restrictions
Reference vs. Input Signal Phase
The 2K processor does not have input buffer memory; 
therefore, be sure to lock and match the phase between 
the reference signal and input signals. If the signal 
phases are not locked and matched, the phase of 
signals, output signals might be corrupted.
System vs. Input Signal Frequency
The 2K processor does not have input buffer memory; 
therefore, be sure to match the frequencies between the 
system settings and input signals. If the frequencies are 
not matched, output signals might be corrupted.
4:2:2 (Y Pb Pr) Output
The 2K Processor has no built-in gamma conversion. 
Therefore, in the output of 4:2:2 (YPbPr color space), 
only conversion from RGB (gamma = 2.2) produces 
the correct hue. The hue varies in other cases.
Video Output in SEARCH and FF/REW
Video output in SEARCH and FF/REW is with low-
resolution images, with low image quality.
SYSTEM setting for RGB and XYZ color 
spaces
The input of color space signals that differ from those 
in SYSTEM results in incorrect color space output.
Playback of recording color space signals on tapes 
that differ from those in SYSTEM results in incorrect 
color space output.
SYSTEM settings for 2048 and 1920 
horizontal samples
Recording and playback depend on the SYSTEM 
settings.
zRecording is based on the number of horizontal 
samples in SYSTEM settings and Tape ID, even 
when different input signals from those in SYSTEM 
are supplied.
zPlayback is based on the number of horizontal 
samples in SYSTEM settings, even when tape with 
a different number of horizontal samples from 
those in SYSTEM is played back.
In the above case, FRONT LED (2048/1920) blinks 
according to SYSTEM settings.
In addition, when a format other than that supporting 
the 2K processor is played back, it blinks rapidly 
according to the SYSTEM settings.
Example 1:
Input of 2048 signals with 1920 selected in 
SYSTEM settings:
On each side, 64 samples are cropped to record 
as 1920 samples. (Tape ID = 1920)
Example 2:
Input of 1920 signals with 2048 selected in 
SYSTEM settings:
Black signals of 64 samples are added to each 
side to record as 2048 samples. (Tape ID = 2048)Example 3: 
Playback of recording tape for 2048 with 1920 
selected in SYSTEM settings:
On each side, 64 samples are cropped for 
playback as 1920 samples.
Example 4: 
Playback of recording tape for 1920 with 2048 
selected in SYSTEM settings:
Black signals of 64 samples are added to each 
side for playback as 2048 samples.
In 4:2:2 output, it appears as normal HD signals 
with normal output due to the Side Crop function.
Example 5: 
Playback of recording tape in the format of 1080/
23PsF 4:2:2 with 1920 selected in SYSTEM settings:
FRONT LED “1920” blinks rapidly. The output 
signals are the freeze frame of the last image.
Differences in the actual image conditions due to 
differences in the number of H Samples between 
SYSTEM settings and input signals (According to the 
SYSTEM settings)
SYSTEM 
settings 
(MENU 
selection)
Input signals Recorded images
2048
2048
1920
1920
2048
1920
1920
2048
1920
2048
192064641920
2048
1920
2048
64641920
19201920 
						

							16
Restrictions (Continued)
Differences in the actual image conditions due to differences in the number of H Samples between SYSTEM settings 
and Tape playback (Tape recording ID) (According to the SYSTEM settings)
Internal signal source (INT-SG)
zThere are four internal signal sources: CB1, CB2, 
BLACK, and WHITE. (10-bit precision)
zXYZ and RGB color spaces are expressed 
differently, resulting in a difference in the internal 
signal format.

CB1:100% Color Bar
CB2:75% Color Bar
CB1:Color Bar Signal Pattern 1
CB2:Color Bar Signal Pattern 2
INPUT CHECK Function
Pressing the INPUT CHECK button changes the TC 
display in the monitor output SUPER and the TCG 
display in the front panel to the internal TCG.
The INPUT CHECK function on the HD-D5 VTR 
Front Panel is disabled.
SYSTEM settings 
(MENU selection)TAPE playback signalsH CROP 
(MENU selection)SAMPLING = 4:4:4 
output imagesSAMPLING = 4:2:2 
output images
20482048
CTR CROP
L CROP
R CROP
1920
CTR CROP
L CROP
R CROP
19202048
1920
1920
2048
1920
1920
2048
1920
1920
64641920
2048
1920
1920
1920
1920
646419201920
2048
19201920 
						

							17
Rack Mounting
The unit can be installed in a 19-inch standard rack using the rack-mount adaptors supplied with the unit. 
We recommend using the slide rails and brackets specified below for the installation.
CC3001-99-0191 slide rails and B-308 brackets are made by CHASSIS TRAK.
For further details, consult your dealer.
1Remove the four feet from the unit’s bottom panel.
zTake care to avoid exposing the unit to vibration
or impact.
2Mount the slide rail inner members onto the unit.
zThe length of the mounting screws is limited.
Use the screws (M4a10) provided with the slide 
rails.
If one or more mounting screws are lost or 
misplaced, use screws less than 10 mm long.
zBe sure to fully tighten the inner members in the four 
places on the left and right.
3Attach the outer members of the slide rails and 
the brackets to the rack.
×Note
Check that the height is the same on the left and 
the right.
4Attach the rack-mount adaptors supplied with the 
unit to the unit.
zUse the screws provided with the rack-mount 
adaptors as the mounting screws.
zBe sure to fully tighten the rack-mount adaptors in 
the two places on the left and the right sides.
5Remove the stoppers of the inner members, and 
install the unit in the rack.
After installation, check that the unit moves 
smoothly.
zKeep the temperature in the rack between 5°C 
(41°F) and 40°C (104°F) 
zUse the rack-mount angular brackets supplied with 
the unit.  
						

							18
Specifications
[GENERAL]
 indicates safety information.
Operating Temperature:
5°C to 40°C (41°F to 104°F) 
Operating Humidity:
10% to 80% (no condensation)
Weight:
Approx. 7.5 kg (16.5 lb)
Dimensions (W a H a D):
(not including supporting feet, jacks, connectors 
and fan.)
424 mm a 87 mm a 470 mm (2U size)
(16-3/4 inches a 3-7/16 inches a 18-1/2 inches)
Recording Video Signal:
2048 a 1080/23.98p, 24p XYZ/RGB 4:4:4
1920 a 1080/23.98p, 24p XYZ/RGB 4:4:4
Video Recording Format:
HD-D5 JPEG2000
Audio Recording Format:
48 kHz/24 bits, 8CH 
Recording Media:
HD-D5 Tape
Recording/Playback Time:
AJ-D5C124LP Approx. 155 min.
Digital Slow:
-1 to +1 times normal speed 
Search Speed:
Max. 50 k
Edit Frame Accuracy:
n0 Frame
[VIDEO]
Sampling Frequency:
74.176 MHz/74.25 MHz
Quantizing:
XYZ/RGB 4:4:4, 12 bits
Video Compression Format:
JPEG2000 (ISO/IEC15444)
Error Correction:
Reed-Solomon product code
Video Bit Rate:
Max. 188 Mbps
_Video Input Signal
Dual Link SDI Input:
BNC a 2, 75 Ω
1920 a 1080/23.98PsF, 24PsF 4:4:4
SMPTE 372M/291M/292M/299M standard
2048 a 1080/23.98PsF, 24PsF 4:4:4
_Video Output Signal
Dual Link SDI Output:
 (Single HD SDI Output in case of 4:2:2)
BNC a 2 a 2, 75 Ω
1920 a 1080/23.98PsF, 24PsF 4:4:4
SMPTE 372M/291M/292M/299M standard
2048 a 1080/23.98PsF, 24PsF 4:4:4
1920 a 1080/23.98PsF, 24PsF YPbPr 4:2:2
  SMPTE 291M/292M/299M standard
Single HD SDI Monitor output:
BNC a 1, 75 Ω (SUPER ON/OFF)
1920 a 1080/23.98PsF, 24PsF YPbPr 4:2:2
SMPTE 292M standard 
(Video Signal only w/o ANC data)
[Audio]
Sampling Frequency:
48 kHz (sync video)
Quantizing:
24 bits
_Audio Input Signal
Dual Link SDI Input: (Embedded Audio)
BNC a 2, 75 Ω (LinkA only)   8CH
SMPTE 299M standard
_Audio Output Signal
Dual Link SDI Output: (Embedded Audio)
BNC a 2 a 2, 75 Ω (LinkA only)   8CH
SMPTE 299M standard Power supply:
Rated Current:AC 120 V, 50/ 60 Hz
0.6 A 
						

							19
Specifications (Continued)
[TC]
_TC Input Signal
Dual Link SDI Input: (Embedded LTC/VITC)
BNC a 2, 75 Ω (LinkA only)
SMPTE 291M standard
_TC Output Signal
Dual Link SDI Output: (Embedded LTC/VITC)
BNC a 2 a 2, 75 Ω (LinkA only)
SMPTE 291M standard
[Other Input and Output]
HD Reference Input:
BNC a 2 (loop-through a1), 
75 Ω automatic termination
HD(1920 a 1080/23.98PsF, 24PsF) tri-level sync
HD SYNC Output:
BNC a 1, 75 Ω
HD(1920 a 1080/23.98PsF, 24PsF) tri-level sync,
Advanced Reference signal for HD-D5 VTRs
Serial Data Output (VTR HD SDI):
BNC a 1, 75 Ω
1920 a 1080/23.98PsF, 24PsF
SMPTE 292M compliance
Serial Data Input (VTR HD SDI):
BNC a 1, 75 Ω
1920 a 1080/23.98PsF, 24PsF
SMPTE 292M compliance
[Accessories (supplied)]
Power cord (1)
Rack-mount adaptor (2)
Weight and dimensions shown are approximate.
Specifications are subject to change without notice. 
						

							Panasonic Broadcast & Television Systems Company
Unit Company of Panasonic Corporation of North America
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094   (201) 348-7000
EASTERN ZONE: 
One Panasonic Way 4E-7, Secaucus, NJ 07094   (201) 348-7196
Southeast Region: (201) 348-7162
WESTERN ZONE: 
3330 Cahuenga Blvd W., Los Angeles, CA 90068   (323) 436-3500
Government Marketing Department:
One Panasonic Way 2E-10, Secaucus, NJ 07094   (201) 348-7587
Broadcast PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880
Emergency after hour parts orders (800) 334-4881
TECHNICAL SUPPORT:
Emergency 24 Hour Service (800) 222-0741
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3   (905) 624-5010
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630   (787) 750-4300
© 2007 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.P