Optoma Zw212st Projector User Manual

							21English
Using the Projector
Adjusting the Projector’s Focus
To focus the image, rotate the focus ring until the image is clear.  
 XGA series:  The projector will focus at distances from  
   1.64 to 8.2 feet (0.5 to 2.5 meters).
 WXGA series:  The projector will focus at distances from   
      1.64 to 8.2 feet (0.5 to 2.5 meters).
Adjusting Projection Image Size
 XGA series:  Projection Image Size from 39.3” to 196.5”   
   (1.0 to 4.99 meters).
 WXGA series: Projection Image Size from 44.6” to 222.8”  
      (1.1 to  meters).
Width
Height
Diagonal
Top View
Side View Projection Distance (D)
Projection Distance (D) Screen
Screen
Screen (W)
Screen (H)
Offset (Hd)
Focus RingFOCUS               
						

							22English
Using the Projector
 This table is for user’s reference only.
XGA
 This table is for user’s reference only.
WXGA
Diagonal length (inch) size of 4:3 ScreenScreen Size W x H Projection Distance (D)Offset (Hd)(m)(inch) (m)(feet)
Width Height WidthHeight widetelewide tele(m)(feet)
40.00  0.81 0.61 31.89  24.02  0.50 0.50 1.64 1.64 0.09 0.30 
60.00  1.22 0.91 48.03  35.83  0.80 0.80 2.62 2.62 0.14 0.45 
70.00  1.42 1.07 55.91  42.13  0.90 0.90 2.95 2.95 0.16 0.53 
80.00  1.63 1.22 64.17  48.03  1.00 1.00 3.28 3.28 0.18 0.60 
90.00  1.83 1.37 72.05  53.94  1.10 1.10 3.61 3.61 0.21 0.67 
100.00  2.03 1.52 79.92  59.84  1.30 1.30 4.26 4.26 0.23 0.75 
120.00  2.44 1.83 96.06  72.05  1.50 1.50 4.92 4.92 0.27 0.90 
150.00  3.05 2.29 120.08  90.16 1.90 1.90 6.23 6.23 0.34 1.13 
180.00  3.66 2.74 144.09  107.87  2.30 2.30 7.54 7.54 0.41 1.35 
250.00  5.08 3.81 200.00  150.00  3.20 3.20 10.50  10.50  0.57 1.87 
300.00  6.10 4.57 240.16 
179.92  3.66 3.66 12.01  12.01  0.69 2.25 
Diagonal length 
(inch) size of 
16:10 ScreenScreen Size W x H Projection Distance (D)Offset (Hd)(m)(inch) (m)(feet)
Width Height WidthHeight widetelewide tele(m)(feet)
40.00  0.86 0.54 33.86  21.26  0.40 0.40 1.31 1.31 0.07 0.22 
60.00  1.29 0.81 50.79  31.89  0.70 0.70 2.30 2.30 0.10 0.33 
70.00  1.51 0.94 59.45  37.01  0.80 0.80 2.62 2.62 0.12 0.38 
80.00  1.72 1.08 67.72  42.52  0.90 0.90 2.95 2.95 0.13 0.44 
90.00  1.94 1.21 76.38  47.64  1.00 1.00 3.28 3.28 0.15 0.49 
100.00  2.15 1.35 84.65  53.15  1.10 1.10 3.61 3.61 0.17 0.55 
120.00  2.58 1.62 101.57  63.78 1.30 1.30 4.26 4.26 0.20 0.66 
150.00  3.23 2.02 127.17  79.53 1.70 1.70 5.58 5.58 0.25 0.82 
180.00  3.88 2.42 152.76  95.28 2.00 2.00 6.56 6.56 0.30 0.98 
250.00  5.38 3.37 211.81  132.68  2.80 2.80 9.18 9.18 0.42 1.37 
300.00  6.46 4.04 254.33 
159.05  3.36 3.36 11.03  11.03  0.50 1.64   
						

							23English
Using the Projector
Projecting Image
When the projector is turned on, it automatically searches for 
connected devices. 
Once a device is detected, the projector projects the image or 
the menu of the input source, such as in:
 ►Network Display: When a local area network or 
wireless network is detected (see "Connect to Network" 
on page 16).
 ►USB Display: When a computer is connected through 
the mini USB port of the projector (see "USB Display 
mode" on page 62).
 ►Memory Drive Display : When a flash drive or SD 
card is detected (see "Memory Drive Display" on page 
47).
Switch Input Source
If the desired input source is not included in the auto search 
function (see Input Source menu) or more than one input 
source devices are connected, you can switch the input source 
manually by doing one of the following:
 ►Press the direct input source key on the remote control.
 ►Press  on the control panel repeatedly to scroll 
through the options.
 ►Press the Source key on the remote control repeatedly  
to scroll through the options.
Refresh Input Source
While the projector is operating and a new input source device 
is connected, press 
 on the control panel or the Re-Sync 
key on the remote control to refresh and synchronize the 
projector with the input sources.
	 Only input 
sources selected 
in the Input 
Source menu 
(see *) will be 
auto searched 
by the projector.
	 The number of 
input sources 
to auto search 
may affect the 
length of time 
for the projector 
to finish the 
search.   
						

							24English
Adjusting the Settings
The Projector has a multilingual On-screen Display menu 
that allows you to make image adjustments and change your 
projector settings.
How to operate 
1. To open the OSD menu, press  on the control panel or 
Menu on the remote control.
2. When the OSD menu is displayed, use   keys to select 
an item on the main menu.
3. While a menu item is highlighted, press  or Enter to 
enter the sub menu.
4. Use the   keys to select the desired item and adjust 
the settings using the   keys.
5.  Press  or Enter to confirm. The screen returns to the 
main menu.
6.  To exit, press  or Menu again. The OSD menu closes and 
the projector automatically saves the new settings.
On-screen Display Menu
Main Menu
Sub Menu Settings        
						

							25English
Adjusting the Settings
Menu Tree
Main Menu Sub Menu Settings
ImageDisplay Mode
Presentation / Bright / 
Movie / sRGB / Blackboard / 
Classroom / User / 3D
Brightness -50 ~ 50
Contrast -50 ~ 50
Sharpness 1 ~ 15
1Color-50 ~ 50
1Tint-50 ~ 50
Advanced Gamma
Film / Video / Graphics / PC
BrilliantColor™ 0 ~ 10
Color Red Gain / Green Gain / Blue 
Gain / Red Bias / Green Bias 
/ Blue Bias / Cyan / Magenta / 
Yellow / Reset 
Color Space Auto / RGB / YUV
Auto / RGB (0~255) / RGB 
(16~235) / YUV
Input Source VGA / S-Video / Video / 
HDMI / Flash Drive / Network 
Display / USB Display
Exit
Display Format
4:3 / 16:9-I / 16:9-II or 16:10 
(ZW210ST) / LBX (ZW210ST) 
/ Native / Auto
Edge Mask 0~10
Zoom -5~25
H Image Shift -50~50
V Image Shift -50~50
V Keystone -40~40
3D 3D Mode
Off / DLP-Link / IR
33D Sync InvertOn / Off   
						

							26English
Adjusting the Settings
Main MenuSub Menu Settings
SetupLanguage
English / Deutsch / Français / 
Italiano / Español / Português 
/ Svenska / Nederlands 
/ Norsk/Dansk / Polski / 
Русский / Suomi / ελληνικά / 
Magyar / Čeština / عربي / 繁
體中文 / 簡体中文 / 日本語 / 
한국어 / ไทย / Türkçe / Farsi
Projection Front / Front-Ceiling / Rear /  
Rear-Ceiling
Menu 
Location Top-Left / Top-Right / Center / 
Bottom-Left / Bottom-Right
2Screen Type
16:10 / 16:9 (WXGA only)
Network Network State
Read-Only
DHCP Read-Only
IP Address Read-Only
Subnet Mask Read-Only
Gateway Read-Only
DNS Read-Only
Apply Yes / No
Exit
4Signal Automatic
On / Off
Phase 0~31
Frequency -5~5
H. Position -5~5
V. Position -5~5
Exit
Security Security
On / Off
Change 
Password
Exit
Projector ID 0~99
Mute On / Off  
						

							27English
Adjusting the Settings
	Please note that the on-screen display (OSD) menus vary according to t\
he signal type 
selected and the projector model you are using.
	 (
1) “Color” and “Tint” are only supported in Video mode. 
	 (
2) 16:9 or 16:10 depend on “Screen Type” setting (Available only in WXGA model).
	 (
3) “3D Sync Invert” is only available when 3D is enabled.
	 (
4) “Signal” is only supported in Analog VGA (RGB) signal.
Main Menu Sub Menu Settings
SetupVolume
0~100
Advanced Logo Optoma / Neutral / User
Logo Capture
Closed 
Captioning Off / CC1 / CC2
Options Source Lock
On / Off
High Altitude On / Off
Information 
Hide On / Off
Keypad Lock On / Off
Background 
Color Red / Blue / Green / Cyan
Test Pattern None / Grid / White Pattern
Advanced Direct Power On On / Off
Auto Power Off 0 ~ 100
Sleep Timer 0 ~ 100
Power Mode ECO / Active
Brightness 
Mode Bright / ECO / Image AI
Exit
Reset   
						

							28English
Adjusting the Settings
IMAGE
 Display Mode
 The projector comes with factory presets designed for 
various types of images. Select an appropriate display 
mode for your source.
 ►Presentation: Good color and brightness suitable for 
PC input.
 ►Bright: Maximum brightness suitable for PC input.
 ►Movie: For home theater.
 ►sRGB: Standardised accurate color.
 ►Blackboard: Select this mode to achieve optimum color 
settings when projecting onto a green blackboard.
 ►Classroom: This mode is recommended for projecting 
in a classroom.
 ►User: User’s settings.
 ►3D: Recommended setting if 3D mode is enabled. 
Adjustments made by the user in 3D will be saved in 
this mode for further use.  
						

							29English
Adjusting the Settings
	“Saturation” and 
“Tint” func-
tions are only 
supported under 
Video mode.
 Brightness
 Adjust the brightness of the image.
 ►Press the  to darken image.
 ►Press the  to lighten the image.
 Contrast
 Contrast controls the degree of dif ference between the 
lightest and darkest parts of the picture. 
 ►Press the  to decrease the contrast.
 ►Press the  to increase the contrast.
 Sharpness
 Adjust the sharpness of the image.
 ►Press the  to decrease the sharpness.
 ►Press the  to increase the sharpness. 
 Color
 Adjust the image color.
 ►Press the  to decrease the color of the image.
 ►Press the  to increase the color of the image. 
 Tint
 Adjust the color balance o f red and green.
 ►Press the  to increase the amount of green in the 
image.
 ►Press the  to increase the amount of red in the image.              
						

							30English
Adjusting the Settings
IMAGE | Advanced
 Gamma
 This allows you to choose a gamma table that has been  
fine-tuned to bring out the best image quality for the input.
 ►Film: for home theater.
 ►Video: for video or TV source.
 ►Graphics: for image source.
 ►PC: for PC or computer source.
 BrilliantColor™
 This adjustable item utilize s a new color-processing 
algorithm and system level enhancements to enable 
higher brightness while providing true, more vibrant colors 
in picture. The range is from “0” to “10”. If you prefer a 
stronger enhanced image, adjust toward the maximum 
setting. For a smoother, more natural image, adjust toward 
the minimum setting.
 
 Color
 Select  to go to the Color Settings menu and then use  
or  to select an item.
 ► Red/Green/Blue/Cyan/Magenta/Yellow: Use  or  to 
select Red, Green, Blue, Cyan, Magenta and Yellow 
Colors.