Optoma X306st Projector User Manual

							21English
User Controls
Control Panel
Control Panel & Remote Control
/
/
Using the Control Panel
POWERRefer to the “Power On/Off the Projector” section on 
pages 16-17.
RE-SYNCAutomatically synchronize the projector to the input 
source.
Enter / Help  / 
Confirm your item selection.
  Help Menu (only available when OSD menu is not 
shown).
SOURCEPress “SOURCE” to select an input signal.
MenuPress “Menu” to launch the on-screen display 
(OSD) menu. To exit OSD, Press “Menu” again.
Four Directional 
Select KeysUse     to select items or make adjust-
ments to your selection.
KeystoneUse   to adjust image distortion caused 
by tilting the projector. (±40 degrees)
Lamp LEDIndicate the projector’s lamp status.
Temp LEDIndicate the projector’s temperature status. 
POWER/STANDBY LEDIndicate the projector’s status.       
						

							22English
User Controls
Remote Control
Using the Remote Control
Power  
Refer to the “Power On/Off the Projector” 
section on pages 16-17.
L ButtonMouse left click.
R ButtonMouse right click.
Page +Use this button to page up.
Page -Use this button to page down.
EnterConfirm your item selection.
SourcePress “Source” to select an input signal.
Re-Sync Automatically synchronizes the projector to 
the input source.
Four Directional 
Select KeysUse     to select items or make 
adjustments to your selection.
PC/Mouse ControlUse     for emulation of USB 
mouse via USB when you press “Switch” 
button.
Keystone +/-Adjust image distortion caused by tilting the 
projector.
Volume +/-Adjust to increase / decrease the volume.
Brightness Adjust the brightness of the image.
3DPress the “3D” to turn the 3D OSD menu 
on/off.
Menu
Press “Menu” to launch the on-screen 
display (OSD) menu. To exit OSD, press 
“Menu” again.
HDMIPress “HDMI” to choose HDMI source.
Menu
Menu
	The interface is subject to model’s specifi-cations.         
						

							23English
User Controls
Using the Remote Control
FreezePress “Freeze” to pause the screen image. 
Press this button again to unlock.
AV muteMomentarily turns off/on the audio and 
video.
S-Video Press “S-Video” to choose S-Video source.
VGAPress “VGA” to choose VGA sources.
VideoPress “Video” to choose Composite video 
source.
SwitchUSB mouse switch.
Mode
Select the display mode from Presentation,
Bright, Movie, sRGB, Blackboard, Class-
room, User and 3D.
ZoomZoom in on an image.
Press    buttons to alter zoom.
Eco+
When Eco+ mode is activated, the bright-
ness level of the content is automatically 
detected to significantly reduced lamp 
power consumption (up to 70%) during 
periods of inactivity.
Menu
Menu
	AV mute: Save up to 70% of the lamp power when AV mute is ap-plied.   
						

							24English
User Controls
 Using the HELP button
The HELP function ensures easy setup and operation. 
 Press the “?” button on the control panel to open the Help 
Menu. 
/
/   
						

							25English
User Controls
	Please refer to the 
“Troubleshooting” 
section on pages 
55-59 for more 
details.
 Help menu button functions only when no input source 
is detected.
 If input source is detected and help button is pressed, the 
following pages will appear to help diagnose any problems. 
						

							26English
User Controls 
						

							27English
User Controls
The Projector has multilingual On-screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1. To open the OSD menu, press “Menu” on the Remote Control or 
Projector Keypad.
2  When OSD is displayed, use   keys to select any item in the 
main menu. While making a selection on a particular page, press 
 or “Enter” key to enter sub menu.
3. Use   keys to select the desired item and adjust the settings 
using   key.
4. Select the next item to be adjusted in the sub menu and adjust as 
described above.
5. Press “Enter” to confirm, and the screen will return to the main 
menu.
6. To exit, press “MENU” again. The OSD menu will close and the 
projector will automatically save the new settings.
On-screen Display Menus
Main Menu
Sub Menu
Settings        
						

							28English
User Controls
Menu Tree
W3055S OSD Menu Tree.xls
Main Menu Sub MenuSettings
ImageDisplay Mode
Brightness -50~50
Contrast -50~50
Sharpness 1~15
Color -50~50
Tint -50~50
Advanced Gamma Film / Video / Graphics / Standard
1~10
Color Temp. Warm / Medium / Cold
Color Settings Hue / Saturation / Gain
White R / G / B
Reset
Exit
Color Space AUTO / RGB / YUV
Signal Automatic On / Off
Phase (VGA) 0~31
Frequency (VGA) -5~5
H. Position (VGA) -5~5
V. Position (VGA) -5~5
Exit
Exit
Reset
DisplayFormat 4:3 / 16:9 / Native / AUTO
Edge Mask 0~10
Zoom  -5~25 (80%~200%)
Image Shift H Image Shift -100~100
V Image Shift -100~100
V Keystone -40~40
Auto Keystone On / Off
3D 3D Mode
3D Format
3D Sync. Invert On / Off
Exit
SetupLanguage
Projection
Menu Location
Screen Type 16:10 / 16:9
Security Security On / Off
Security Timer Month / Day / Hour
Change Password ³
Exit Presentation / Bright / Movie / sRGB / 
Blackboard / User / 3D
#1
#1
BrilliantColor™ 
Red / Green / Blue 
/ Cyan / Magenta / 
Yellow / 
#3AUTO / RGB (0-255) / RGB (16-235) / 
YUV
#2
#4
#5
4:3 / 16:9 or 16:10 / LBX / Native / 
AUTO
#5
Off / DLP-Link / IR#6Auto / SBS / Top and Bottom / Frame 
Sequential
#6
English / Deutsch / Français / 
Italiano / Español / Português / 
Svenska / Nederlands / Norsk/Dansk / 
Polski / Suomi / Jmkkdbc / 
0  / 
Magyar /  ýeština /  6
						

							29English
User Controls
W3055S OSD Menu Tree.xls
Main Menu Sub MenuSettings
SetupProjector ID 0~99
Audio Settings Internal Speaker On / Off
Mute On / Off
Audio Input Default / Audio1 / Audio2
Volume Audio 0~10
Mic 0~10
Volume 0~10
Advanced Logo Default / Neutral
Closed Captioning Off / CC1 / CC2
Exit
LAN Settings LAN State
DHCP On / Off
IP Address
Gateway
DNS
Apply Yes / No
Exit
OptionsInput Source
Source Lock On / Off
High Altitude On / Off
Information Hide On / Off
Keypad Lock On / Off
Test Pattern None / Grid / White Pattern
Background Color Black / Red / Blue / Green / White
Advanced Direct Power On On / Off
Auto Power Off (min.) 0~180
Sleep Timer (min.) 0~990
Quick Resume On / Off
Power Mode (Standby) Active / Eco
Exit
Lamp Settings Lamp Hours
Lamp Reminder On / Off
Brightness Mode Bright / Eco
Lamp Reset Yes / No
Exit
Optional Filter Installed Yes / No
Filter Usage Hours 0~9999
Filter Reminder Off / 300hr / 500hr / 800hr / 1000hr
Filter Reset Yes / No
Exit
Reset Yes / No
#5
#5
#5
#4
#5
Subnet mask
#4VGA1 / VGA2 / S-Video / Video / HDMI#5VGA1 / VGA2 / Video / HDMI
Optional Filter 
Settings 
	Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are using.
	(#1) “Color” and “Tint” are only supported in Video mode. 
	(#2) “Signal” is only supported in Analog VGA (RGB) signal.
	(#3) For HDMI Source only. 
	(#4) For Type A model only.
	(#5) For Type B model only.
	(#6)   “3D Sync Invert” is only available when 3D is enabled and this mode 3D is for DLP  link glass only. 
	(#7) For WXGA model only. 
						

							30English
User Controls
IMAGE
 Display Mode
There are many factory presets optimized for various types of  
images.
 Presentation: Good color and brightness from PC input.
 Bright: Maximum brightness from PC input.
 Movie: For home theater.
 sRGB: Standardised accurate color.
 Blackboard: This mode should be selected to achieve optimum 
color settings when projecting onto a blackboard (green).
 User: User’s settings.
 3D: Recommend setting for 3D mode enabled. Any further ad-
justments by the user in 3D will be saved in this mode for further 
use.
 Brightness
Adjust the brightness of the image.
  Press the  to darken image.
  Press the  to lighten the image.
 Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. 
  Press the  to decrease the contrast.
  Press the  to increase the contrast.