Optoma Tx782 Projector User Manual

3English

User Controls

 Language
Choose the multilingual OSD menu. Press  or  into the sub 
menu and then use the  or  key to select your preferred  
language. Press “Enter” to finalize the selection. 
Setup | Language 

32English

User Controls

Setup
 Projection
    Front-Desktop
The factory default setting.
    Rear-Desktop
When you select this function, the projector reverses the image 
so you can project behind a translucent screen.
    Front-Ceiling 
When you select this function, the projector turns the image 
upside down for ceiling-mounted projection.
    Rear-Ceiling 
When you select this function, the projector reverses and turns 
the image upside down at same time. You can project from 
behind a...

33English

User Controls

Setup
 Menu Location
Choose the menu location on the display screen.
 Mute
 Choose the “On” to turn mute on. 
 Choose the “Off” to turn mute off. 
 Volume
  Press the  to decrease the volume.
  Press the  to increase the volume.
  Projector ID
Allow the RS232 control of an individual projector. Range 01-99.
Setup 

34English

User Controls

Setup | Signal
 Phase
Synchronize the signal timing of the display with the graphic card. 
If you experience an unstable or flickering image, use this function 
to correct it.
 Frequency
Change the display data frequency to match the frequency of your 
computer’s graphic card. If you experience a vertical flickering bar, 
use this function to make an adjustment.
 H. Position
 Press the  to move the image left.
 Press the  to move the image right. 
 V. Position
 Press the  to...

35English

User Controls

Setup
 RS232
 RS232: Allow RS232 control of an individual projector.
 Network: Allow projector control via web browser (Internet Ex-
plorer) using the network (Default setting).
 Wireless
Choose “On” to turn on the wireless mode.
	“Wireless” is only functional with optional wireless module. 

36English

User Controls

Setup | Advanced
 Logo
Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD menu, the new setting will take effect on next open.
 Optoma: The default startup screen of Optoma projector.
 User: Use memorize picture from “Logo Capture” function.
 Logo Capture
Press “Enter” to immediately capture a picture what on the dis-
play screen. 

37English

User Controls

Setup | Network
 Network State
To display network information.
 DHCP
Use this function to select your desired startup screen. If you 
change the setting from one to another, when you exit the OSD 
menu, the new setting will take effect on next open.
 On: Assign an IP address to the projector from the DHCP 
server automatically.
 Off: Assign an IP address manually.
  IP Address
Select an IP address.
 Subnet Mask
Select subnet mask number.
 Gateway
Select the default gateway of...

38English

User Controls

1.  Fill  in  a  new  IP,  a  subnet  mask,  a  gateway  and  a  DNS  in  the 
dialogue box.
2.  Then  choose  apply  and  press “”  botton  to  effectuate  the 
confi  guration process.
3.  Open  your  web  browser  and  type  in  from  the  OSD  LAN  screen 
then the web page will display as below:
4. Open “Control Panel” to control your projector. 
 
For example:  Use  Microsoft  Internet  Explorer  (IE)  web  browser 
to  control  the  projector  ,  the  IP  address  is...

39English

 User Controls

Step 2: Select apply and press “Enter” button to submit function or press “menu” key to 
exit.
Step  3: To  open  Network  Connections,  click Start,  click Control  Panel,  click Network 
and  Internet  Connections,  and  then  click Network  Connections.  Click  the connection  you  want  to  confi  gure,  and  then,  under Network  Tasks  ,  click Change settings of this connection.
Step  4:  On  the General  tab,  under This  connection  uses  the  following  items,  click...

40English

User Controls

Setup | Security
 Security
 On: Choose “On” to use security verification when the turning 
on the projector.
 Off: Choose “Off” to be able to switch on the projector without 
password verification.
 Security Timer
Select the time (Month/Day/Hour) function to set the number of 
hours the projector can be used. Once this time has elapsed you 
will be requested to enter your password again.