Optoma Tw631 3d Projector User Manual

							EN-31 Power mode (standby)
Set whether the VGA OUT function works when the projector is in standby
(powered off but connected to AC power).
„ Eco mode: The VGA OUT function will not work when the projector is in 
standby.
„ Active mode: The VGA OUT and AUDIO OUT functions will work when 
the projector is in standby.
Auto Power Off
Set the countdown timer interval. The countdown timer will start, when there
is no signal being sent to the projector. Then projector will automatically
power off when the countdown has finished (in minutes).
Quick Resume
If the projector is accidentally turned off, this feature allows the projector to 
be instantly powered on again within 100 seconds of power down.
Source Lock
„On: The projector will search specified connection port.
„Off: The projector will search for other signals if the current input signal is 
lost.
Brightness Mode
„Bright: Choose “Bright” to increase the brightness.
„Eco: Choose “Eco” to dim the projector lamp which will lower power 
consumption and extend the lamp life by up to 120%.
„Eco+: Choose “Eco+” to dim the projector lamp which will automatically 
detect the brightness level of the content and reduce lamp power 
consumption (up to 70 percent) during periods of inactivity.
High Altitude
Use this function to allow the fans operates at full speed continuously to
achieve proper high altitude cooling of the projector.
OSD Timeout
Duration of OSD menu display countly starts (at idle state by second).
Closed Captioning
Enable or disable closed captioning by selecting CC1,CC2 or Off.
Projector ID
ID definition can be set up by menu (range 0~99), and allow user control an
individual projector by RS232.
Network 
Allow you to configure the LAN settings.
„Network State:Display the network connection status.
„DHCP: This protocol automatically assign IP Address to networked  
						

							 EN-32devices.
„On: Assign an IP address to the projector from an external DHCP 
server automatically.
„Off: Assign an IP address manually.
„IP Address: Select an IP address.
„Subent mask: Select subnet mask number.
„Gateway: Select the default gateway of the network connected to the 
projector.
„DNS: Select DNS number.
„Apply: Press   and then choose Yes to apply the selection.
Wireless
This setting is only for wireless module use.
Wireless is only functional with VGA 1 connector.
3D Mode
„On: Enable 3D Mode function.
„Off: Disable 3D Mode function.
When 3D Sync is set to On, the settings for input source or broadcast
device are required as below:
1. For S-VIDEO and VIDEO input source, signal type should be NTSC (60).
2. For computer input source, the hardware and software requirements 
should be Windows 7 operating system, 3D videos and professional 3D 
video player softwares. Computers output frequency should be 120Hz 
and display card should be higher than NVIDIA 9800.
3D Sync Invert
„On: Invert left and right frame contents.
„Off: Default frame contents. 
						

							EN-33
Language
Select the language used by the on-screen menu.
Factory Default
Restore settings to factory default . 
						

							 EN-34
Use web browser to control your projector
1. Turn on DHCP to allow the DHCP server to automatically assign an IP,
or manually enter the required network information.
2. Then choose apply and press   button to complete the configuration
process.
3. Open your web browser and type in the projectors IP address from the
OSD LAN screen. The following web page will display as below:
•When you used the projector IP address, you will can not link to your service 
server. 
						

							EN-35 4. The crestron control settings can be found in the [tools] tab.(see picture)
Please note, each field can only contain a limited number of characters,
as shown in the table below. (spaces and the other punctuation
included):
CategoryItemInput-Length (characters)
Crestron ControlIP Address 15
IP ID 2
Port 5
ProjectorProjector Name 10
Location 9
Assigned To 9
Network 
ConfigurationDHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User PasswordEnabled (N/A)
New Password 15
Confirm 15
Admin PasswordEnabled (N/A)
New Password 15
Confirm 15 
						

							 EN-36
Connect you computer to the projector
1. Find an IP Address (10.0.50.100) from LAN function of projector.
2. Select Apply and press Enter button to submit function or press
MENU key to exit.
3. To open Network Connections, click Start, click Control Panel, click
Network and Internet Connections, and then click Network
Connections. Click the connection you want to configure, and then,
under Network Tasks , click Change settings of this connection.
4. On the General tab, under This connection uses the following items,
click Internet Protocol (TCP/IP), and then click Properties. 
						

							EN-37 5. Click Use the following IP address, and type in as below:.
„IP address:10.0.50.101
„Subnet mask:255.0.0.0
„Default gateway:10.0.50.254
6. To open Internet Options, click IE web browser, click Internet Options,
click the Connections tab and click LAN Settings.... 
						

							 EN-387. The Local Area Network (LAN) Setting dialog box appears, In the Proxy
Server area, cancel the Use a proxy server for your LAN check box.,
then click OK button twice.
8. Open your IE and type in the IP address of 10.0.50.100 in the URL then
press Enter key.
Crestron RoomView Control Tool
Crestron RoomViewTM provides a central monitoring station for 250+ control 
systems on a single Ethernet network (more are possible. the number 
depends on the combination of IP ID and IP address). Crestron RoomView 
monitors each projector, including projectors online status, system power, 
lamp life, network setting and hardware faults, plus any custom attribute as 
defined by the Administrator. The Administrator can add, delete, or edit room 
information, contact information and events, which are logged automatically 
by the software for all users.(Operation UI as following image)
1. Main Screen
„Crestron RoomView function support is dependent on models. 
						

							EN-39 2. Edit Room
3. Edit Attribute 
						

							 EN-40 4. Edit Event
„For more information, please visit http://www.crestron.com & 
www.crestron.com/getrommview.