Optoma Tw631 3d Projector User Manual

EN-41
Appendix
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp
gradually decreases and the lamp becomes more susceptible to breakage.
We recommend replacing the lamp if a warning message is displayed. Do
not attempt to replace the lamp yourself. Contact the qualified service
personnel for replacement.
Note
„The lamp is extremely hot right after turning off the projector. If you touch the lamp, you may
scald your finger. When you replace the lamp, wait for at...

 EN-42
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Remove the screw in the side of the lamp cover. 1
5. Remove the cover. 2
6. Loosen the screws from the lamp module. 3
7. Raise the handle, and lift out the module. 4
8. Insert the new lamp module into the projector and tighten the screws.
9. Replace the lamp cover and tighten the screw.
10. Turn on the projector.  If the lamp does not turn on after the warm-up 
period, try...

EN-43
Ceiling mount installation
1. To prevent damage to your projector, please use the Optoma ceiling 
mount.
2. If you wish to use a third party ceiling mount kit, please ensure the screws 
used to attach a mount to the projector meet the following specifications:
„Screw type: M4*3
„Maximum screw length: 8mm
„Minimum screw length: 6mm
Note
„Please note that damage resulting from incorrect installation will void the warranty.
Warning
1.If you buy a ceiling mount from another company, please be sure to...

 EN-44
Compatibility Modes
Computer: 
Mode Resolution H-Sync [KHz] V-Sync [Hz]
640 x 350 31.5 70
640 x 350 37.9 85
720 x 350 31.5 70
640 x 400 31.5 70
640 x 400 37.9 85.1
720 x 400 31.5 70
720 x 400 37.9 85
720 x 576 - 50
720 x 576 - 60
VGA 640 x 48031.5 60
-67
37.9 72.8
37.5 75
43.3 85
SVGA 800 x 60035.2 56.3
37.9 60.3
46.9 75
48.1 72.2
-80
53.7 85.1
832 x 624 - 72
832 x 624 - 75
1024 x 576 - 50
1024 x 576 - 60
XGA 1024 x 76848.4 60
56.5 70.1
57.7 72
60 75
68.7 85
1152 x 864-60
-70
-75
-85
1152 x 870 -...

EN-45 HD720 1280 x 720 - 60
HD720 1280 x 720 - 75
HD720 1280 x 720 - 85
WXGA 1280 x 76847.4 60
-75
-85
WXGA-800 1280 x 800 - 60
SXGA 1280 x 960 - 60
SXGA 1280 x 102464 60
80 75
91.1 85
1366 x 768 - 60
1440 x 900 55.935 60
SXGA+ 1400 x 1050 - 60
UXGA 1600 x 1200 75 60
HDTV 1920 x 1080 33.8 30
1920 x 1080 28.1 25
1920 x 1080i - 50
1920 x 1080i - 60
1920 x 1080p - 24
1920 x 1080p - 25
1920 x 1080p - 30
1920 x 1080p - 50
1920 x 1080p - 60
1280 x 720 45 60
1280 x 720p - 50
1280 x 720p - 60
SDTV 720 x 576 31.3...

 EN-46
Video: 
NTSC NTSC M/J, 3.58MHz, 4.43MHz
PAL PAL B/D/G/H/I/M/N, 4.43MHz
SECAM SECAM B/D/G/K/K1/L, 4.25/4.4 MHz
Component 480i/p, 576i/p, 720p(50/60Hz), 1080i(50/60Hz)
1080P(24/25/30/50/60Hz)
SDTV 480i/p, 576i/p
HDTV 720p(50/60Hz), 1080i(50/60Hz), 1080P(24/25/30/50/60Hz) 

EN-47
RS232 Commands and Protocol Function 
List
RS232 Pin Assignments
D-Sub 9 pin
11 CD
2RXD
3TXD
4DTR
5GND
6DSR
7RTS
8CTS
9RIWire List
C1 COLOR C2
1 Black 1
2Brown2
3Red3
4Orange4
5 Yellow 5
6 Green 6
7Blue7
8 Purple 8
9White9
SHELL DW SHELL 

 EN-48
RS232 Protocol Function List
Note
„There is a  after all ASCII commands.
„0D is the HEX code for  in ASCII code.
Baud Rate : 9600 
Data Bits: 8  
Parity: None
Sto p Bits: 1
Flow Control : None
UART16550 FIFO: Disable
Projector Return (Pass): P 
Projector Return (Fail): F XX=01-99, projectors ID,
XX=00 is for all projectors
SEND to projector
232 ASCII Code HEX Code Function  Description
~XX00 1 7E 30 30 30 30 20 31 0D Power ON
~XX00 0 7E 30 30 30 30 20 30 0D Power OFF (0/2 for backward compatible)...

EN-49
~XX60 3 7E 30 30 36 30 20 33 0D 16:9-ll (XGA)/16:9 or 16:10 ( WXGA)
 ~XX60 5 7E 30 30 36 30 20 35 0D LBX (WXGA)
~XX60 6      7E 30 30 36 30 20 36 0D     Native 
~XX60 7    7E 30 30 36 30 20 37 0D  Auto 
~XX62 n 7E 30 30 36 32 20 a 0D Zoom n = -5 (a=2D 35) ~ 5 (a=35)
~XX66 n 7E 30 30 36 36 20 a 0D V Keystone n = -40 (a=2D 33 30) ~ 40 (a=34 30)
~XX230 1 7E 30 30 32 33 30 20 31 0D 3D Mode DLP-Link
~XX230 0 7E 30 30 32 33 30 20 30 0D 3D Mode Off
~XX231 1 7E 30 30 32 33 31 20 31 0D 3D Sync Invert  On...

 EN-50
~XX110 1 7E 30 30 31 31 30 20 31 0D Brightness Mode Bright
~XX110 0 7E 30 30 31 31 30 20 30 0D Eco (0/2 for backward compatible)
~XX110 3 7E 30 30 31 31 30 20 33 0D Eco
+~XX111 1 7E 30 30 31 31 31 20 31 0D Lamp Reset Yes
~XX111 0 7E 30 30 31 31 31 20 30 0D No (0/2 for backward compatible)
~XX112 1 7E 30 30 31 31 32 20 31 0D Reset Yes
~XX99 1 7E 30 30 39 39 20 31 0D RS232 Alert Reset Reset  System Alert 
SEND to emulate Remote
~XX140 1 7E 30 30 31 34 30 20 31 0D Power
~XX140 3                7E 30...