Optoma Tw610st Projector User Manual

41English
User Controls
SETUP | Advanced
 Logo
Use this function to set the desired startup screen. If changes are 
made they will take effect the next time the projector is powered 
on.
 Optoma: The default startup screen.
 User: Use stored picture from “Logo Capture” function.
  Logo Capture
Press   to capture an image of the picture currently displayed
on screen.
  Closed Captioning
Use this function to set the desired startup screen. If changes are 
made they will take effect the next time the...

42
English
User Controls
SETUP | Network
  Network State
Display the network connection status.
 DHCP
Use this function to select your desired startup screen. If you 
change the setting from one to another, when you exit the OSD 
menu, the new setting will take effect on next open.
 On: Assign an IP address to the projector from an external 
DHCP server automatically.
 Off: Assign an IP address manually.
  IP Address
Select an IP address.
 Subnet Mask
Select subnet mask number.
 Gateway
Select the...

43English
User Controls
1. Turn on DHCP to allow the DHCP server to automatically assign 
an IP, or manually enter the required network information.
2. Then choose apply and press  “” button to complete the 
configuration process.
3.  Open your web browser and type in from the OSD LAN screen 
then the web page will display as below:
4. Open “ Control Panel ” to control your projector. 
 
When making a direct connection from your computer to the  projector
Step 1: Find an IP Address (192.168.6.74) from...

44
English
User Controls
Step 2: Select apply and press  “Enter” button to submit function or press “ menu” key to 
exit.
Step 3:  To open Network Connections, click  Start, click Control Panel, click Network 
and Internet Connections , and then click Network Connections. Click the 
connection you want to configure, and then, under  Network Tasks 
 , click 
Change settings of this connection .
Step 4: On the General tab, under  This connection uses the 
following items , click Internet 
Protocol (TCP/IP)...

45English
User Controls
 Source Lock
 
On:  The projector will only search current input connection.
 Off: The projector will search for other signals if the current 
input signal is lost.  
 High Altitude
When “On” is selected, the fans will spin faster. This feature is 
useful in high altitude areas where the air is thin.
 Information Hide
 
On: Choose “On” to hide the info message.
 Off: Choose “Off” to show the “searching” message.
 Keypad Lock
When the keypad lock function is “On”, the control...

46
English
User Controls
OPTIONS | 
Advanced
  Direct Power On
Choose “On” to activate Direct Power mode. The projector will 
automatically power on when AC power is supplied, without 
pressing the “
” key on the projector control panel or on the 
remote control.
  Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, 
when there is no signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
 Sleep...

47English
User Controls
OPTIONS |   
Lamp Settings
  Lamp Hours
Display the projection time.
 Lamp Reminder
Choose this function to show or to hide the warning message 
when the changing lamp message is displayed.   
The message will appear 30 hours before suggested replacement 
of lamp.
  Brightness Mode
  
STD: Choose “STD” to dim the projector lamp which will lower 
power consumption and extend the lamp life. 
 BRIGHT: Choose “BRIGHT” to increase the brightness. 
  Lamp Reset
Reset the lamp hour...

48
English
Appendices
  No image appears on-screen
 
Ensure all the cables and power connections are correctly and 
securely connected as described in the “Installation” section.
  Ensure all the pins of connectors are not bent or broken.
 Check if the projection lamp has been securely installed. Please 
refer to the “Replacing the lamp” section.
  Make sure you have removed the lens cap and the projector is 
switched on.
  Ensure that the “AV mute” feature is not turned on.
 Partial, scrolling or...

49English
Appendices
 7.  Click on “Show all devices”. Next, select “Standard monitor 
types” under the SP box; choose the resolution mode you need 
under the “Models” box. 
  8.  Verify that the resolution setting of the monitor display is lower 
than or equal to  UXGA (1600 × 1200). 
 If you are using a Notebook:
  1.  First, follow the steps above to adjust resolution of the   
computer.
  2.  Press the appropriate keys listed below for your notebook 
manufacturer to send signal out from notebook to...

50
English
Appendices
  Image is out of focus
 
Make sure the lens cap is removed.
 Adjust the Focus Ring on the projector lens. 
 Make sure the projection screen is between the required distance. 
See page 16.
  The image is stretched when displaying 16:9 DVD title
 
When you play anamorphic DVD or 16:9 DVD, the projector will 
show the best image when the projector display mode is set to 
16:9 in the OSD.
 If you play 4:3 format DVD titles, please change the format to 4:3 
in the projector OSD.
...