Optoma Tw330 Projector User Manual

							
English

Introduction

Remote Control
1. Power On/Off
2.  Laser LED
3.  Laser Button
4.  Enter/Mouse Left Click
5.  PC/Mouse Control
6.  Mouse Right Click
7.  Brightness
8.  Re-Sync
9.  Enter
10.   Zoom
11.  Freeze
12.  S-Video Source
13.  Video Source
14.  Number Buttons
15.  Page Down
16.  VGA Source
17.  Blank
18.  HDMI Source
19.  Menu
20.    Four Directional Select 
Keys
21.  Source
22.  Keystone +/-
23.  Page Up
5
6
8
11
12
18
21
123
19
22
15
7
23
920
17
16
10
13
14
4 
						

							
2English

Installation

 VGA,DVI

DVD player, Set-top BoxHDTV receiver

S-Video Output

Video Output

E62405SPR

MOLEX

Connecting the Projector
	Due to the  difference in applications for each country, some regions may have different accessories.
1...............................................................................................................Power Cord2.................................................................................................................USB Cable3................................................................................................................VGA Cable 4.......................................................................HDMI Cable (Optional Accessory) 5.....................................................................S-Video Cable (Optional Accessory) 6....................................................Composite Video Cable (Optional Accessory) 7.......................................SCART RGB/S-Video Adapter (Optional Accessory) 8.............................................................DVI/HDMI Cable (Optional Accessory) 
1
23
4
5
6
7
8  
						

							
3English

Installation

Powering On the Projector
1. Open the lens cap. 
2.  Ensure that the power cord and signal cable are securely 
connected.  The Power LED will be Amber.
3.  Turn on the lamp by pressing “Power” button either on 
the top of the projector or pressing “Power” button on the 
remote. The Power LED will flash green.
  The startup screen will display in approximately 10 seconds. 
The first time you use the projector, you can select your 
preferred language from quick menu after the startup screen 
display.
4.  Turn on your source (computer, notebook, video player, 
etc.). The projector will detect your source automatically.
	If the screen displays “No Signal”, please make sure the signal 
cables are securely connected.
	If you connect multiple sources at the same time, press the 
“Source” button on the control panel or direct source key on the 
remote control to switch between inputs.
Powering On/Off the Projector
	Turn on the projector first and then select the signal sources.
2Power
Lens Cap1
Power LED 
						

							
4English

Installation

Warning Indicator
 When the “LAMP” indicator lights red, it indicates prob-
lem with the lamp and the projector will automatically shut 
down by itself. Please contact your local reseller or service 
center. See pages 50-51. 
  When the “TEMP” indicator lights red, it indicates the pro-
jector has overheated. The projector will automatically shut 
itself down.
  Under normal conditions, the projector can be switched on 
again after it has cooled down. If the problem persists, you 
should contact your local dealer or our service center. 
See pages 50-51. 
 When the “TEMP” indicator flashes red, it indicates the fan 
has failed. Please contact your local dealer or our service 
center. See pages 50-51. 
Powering Off the Projector
1.   Press the “Power” button to turn off the projector lamp, 
you will see a message displayed on the projector’s screen. 
2.  Press the “Power” button again to confirm, otherwise the 
message will disappear after 15 seconds.
  When you press “Power” button a second time, the sys
-
tem will show the countdown timer on the screen. 
3.  The cooling fans continue to operate for about 10 seconds 
for cooling cycle. When the Power LED turns to Amber, 
the projector has entered standby mode.
	If you wish to turn the projector back on, you must wait until 
the projector has completed the cooling cycle and has entered 
standby mode. Once in standby mode, simply press “Power” 
button to restart the projector.
4.  Disconnect the power cord from the electrical outlet and 
the projector.
5.  Do not turn on the projector immediately following a 
power off procedure. 
						

							
5English

Installation

Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with tilt-adjustment foot for  
adjusting the image height.
 To raise the image:
 Use screw in foot to raise the image to the desired height 
angle and fine-tune the display angle .
 To lower the image:
   Use screw in foot to lower the image to the desired height 
angle and fine-tune the display angle .
Tilt-Adjustment Feet
1 
						

							
6English

Installation
Adjusting the Projector’s Zoom / Focus
Adjusting Projection Image Size
You  may  turn  the  zoom  lever  to  zoom  in  or  out.  To  focus  the  
image,  rotate  the  focus  ring  until  the  image  is  clear.  The  pro-
jector  will  focus  at  distances  from  3.3  to  39.4  feet  (1.00  to  12.0 
meters). 
Zoom Lever
Focus Ring
Screen(Diagonal)
Max.30" (76.1cm)90" (228.2cm)150" (380.4cm)210" (532.6cm)270" (684.7cm)359" (913.0cm)
Min.27" (69.4cm)82" (208.1cm)137" (346.8cm)191" (485.6cm)246" (624.3cm)328" (832.4cm)
ScreenSize
Max.(WxH)25.4” x 15.9”65 x 40cm76.2” x 47.6”194 x 121cm127.0” x 79.4”323 x 202cm177.8” x 111.1”452 x 282cm228.6” x 142.9”581 x 363cm304.8” x 190.5”774 x 484cm
Min.(WxH)23.2” x 14.5”59 x 37cm69.5” x 43.4”177 x 110cm115.8” x 72.4”294 x 184cm162.1” x 101.3”412 x 257cm208.4” x 130.3”529 x 331cm277.9” x 173.7”706 x 441cm
HdMax.1.97” (5.0cm)5.91” (15.0cm)9.84” (25.0cm)13.78” (35.0cm)17.72” (45.0cm)23.62” (60.0cm)
Min.1.79” (4.6cm)5.38” (13.7cm)8.97” (22.8cm)12.56” (31.9cm)16.15” (41.0cm)21.54” (54.7cm)
Distance3.3’ (1.0m)9.8’ (3.0m)16.4’ (5.0m)23.0’ (7.0m)29.5’ (9.0m)39.4’ (12.0m)
	This graph is for user’s reference only.
82(208.1cm)
137(346.8cm)
191(485.6cm)
246(624.3cm)
328(832.4cm)
30(76.1cm)
90(228.2cm)
150(380.4cm)
210(532.6cm)
270(684.7cm)
359(913.0cm)
3.3(1.0m)
39.4(12.0m)29.5(9.0m)23.0(7.0m)16.4(5.0m)9.8(3.0m)
27(69.4cm)
Width
Height
Diagonal
Hd 
						

							
7English

User Controls
Control Panel
Control Panel & Remote Control
There are two ways for you to control the functions:  
Control Panel and Remote Control.
Using the Control Panel
PowerRefer to the “Power On/Off the Projector” section 
on pages 13-14.
MenuPress “Menu” to launch the on-screen display 
(OSD) menu. To exit OSD, Press “Menu” again.
EnterConfirm your item selection.
SourcePress “Source” to select the input signal source.
Re-SyncAutomatically synchronize the projector to the 
input source.
Keystone /Adjust image distortion caused by tilting the 
projector (±18 degrees)
Four Directional 
Select Keys
Use     to select items or make adjustments 
to your selection.
  Power LEDIndicate the projector’s status.
  Lamp LEDIndicate the projector’s lamp status.
   Temp LEDIndicate the projector’s temperature status.  
						

							
8English

User Controls

Remote ControlUsing the Remote Control
PowerRefer to the “Power On/Off the Projector” section on pages 13-14.
Laser 
Button
Aim the remote at the viewing screen, 
press and hold this button to activate the 
laser pointer.
PC/ Mouse 
Control
The PC/ Mouse Control can be used to 
control mouse movement. The mouse 
function is enabled using the USB cable to 
connect your computer and the projector.
EnterConfirm your item selection/Mouse Left 
Click
Keystone 
+/-
Adjust  image  distortion  caused by  tilting 
the projector. 
R ButtonMouse Right Click
Page +Use the button to page up.
BrightnessAdjust the brightness of the image.
SourcePress “Source” to select the input signal 
source at the next terminal.
EnterConfirm your item selection.
Re-SyncAutomatically synchronize the projector to 
the input source.
MenuPress “Menu” to launch the on-screen 
display (OSD) menu. To exit OSD, Press 
”Menu” again.
Page -Use the button to page down.
ZoomZoom the projector display in or out. 
						

							
9English

User Controls

Remote ControlHDMI Press “HDMI” to choose source from 
HDMI connector.
FreezePress “Freeze” to pause the screen image. 
Press this button again to unlock.
BlankMomentarily turn off the video. Press this 
button again to unlock.
S-VideoPress “S-Video” to choose S-Video source.
VGAPress “VGA” to choose VGA source.
Four Direc-
tional Select 
Keys
Use        to select items or make 
adjustments to your selection.
VideoPress “Video” to choose Composite video   
source. 
						

							
20English

User Controls

The Projector has multilingual On-screen Display menus 
that allow you to make image adjustments and change a 
variety of settings. The projector will automatically detect  
the source. 
How to operate 
1. To open the OSD menu, press “Menu” on the Remote Control or 
Projector Keypad.
2  When OSD is displayed, use   keys to select any item in the 
main menu. While making a selection on a particular page, press 
 or “Enter” key to enter sub menu.
3. Use   keys to select the desired item and adjust the settings 
by   key.
4. Select the next item to be adjusted in the sub menu and adjust as 
described above.
5. Press “Enter” to confirm, and the screen will return to the main 
menu.
6. To exit, press “Menu” again. The OSD menu will close and the 
projector will automatically save the new settings.
On-screen Display Menus
Main Menu
Sub MenuSetting