Optoma Tw1692 Projector User Manual

							English
Rear View
1. AC IN (Power)
2. USB Connector
3. Audio Input Connector
4. S-Video Input Connector
5. Video Input Connector
6. VGA/SCART Input Connector
7. HDMI Connector
8. Kensington™ Lock Port
9. Ventilation Opening
AC  I N
I I II
8
1234567
9
Introduction 
						

							English
Remote Control
 
HDMI
1
3
5
2
4
9
7
23
20
19
1415
24
8
12
11
10
13
16
17
18
21
226
1. Button LED
2. Power On/Off
3. Laser Button
4. Page Up
5. Mouse Right Click
6. Four Directional  Select Keys
7. Re-Sync
8. Page Down
9. Volume +/-
10. Menu
11. Zoom
12. AV mute
13. Video Source
14. VGA Source
15. Freeze
16. S-Video Source
17. HDMI
18. Brightness
19.
Number Buttons
(for password input)
20. Keystone +/- 
21. Source
22. Enter
23. Mouse Left Click
24. PC/Mouse control
Introduction 
						

							English
Connecting the Projector
Connect to Computer / Notebook
1. Power Cord
2. USB Cable
3. Audio-in (mini jack)
4. S-Video Cable
5. Video Cable
6. VGA Cable
7. HDMI Cable
v Due to the  difference in  
applications 
for each  
country, some 
regions may 
have different 
accessories.
Installation
I III1
4
5
2
3
6
7 
						

							English
Connect to Video Sources
1. Power Cord
2. Component Cable (optional)
3. RGB to Component Adapter (optional)
4. Stereo system cable (optional)
5. RCA Video Cable
6. SCART to RGB & S-Video Adapter (optional)
7. VGA Cable
8. S-Video Cable (optional)
9. HDMI Cable
I I II
4
DVD Player, Set-top Box,
HDTV receiver
4
6
8
2
3
7
5
9
1
v Due to the difference in 
applications for 
each country, 
some regions 
may have  
different  
accessories.
Installation 
						

							English
Powering On / Off the Projector
Powering On the Projector
1. Connect the power cord to the projector.
2. Turn On the connected devices.
3. Ensure the Power LED is steady (flashing) and then press the Power button to turn On the projector.  
 
The projector splash screen displays and connected devices are 
detected. If the connected device is a PC, press the appropriate 
keys on the computer keyboard to switch the display output to 
the projector. (Check the user manual of the PC to determine the 
appropriate Fn key combination to change display output.)  
 
See Setting an Access Password (Security Lock) on page 37  
if security lock is enabled.
4. If more than one input device is connected, press the “Source” \
button to switch between devices sequentially.  
For direct source selection, see page 21.  
(DVD and HDTV are supported through the VGA connector)
v Turn on the  projector first 
and then  
select the  
signal sources.
Installation 
						

							English
Powering Off the Projector
1. Press POWER  to turn off the projector lamp, a message displays on the 
projector’s screen.
2. Press  POWER again to confirm, otherwise the message disappears 
after 15 seconds. 
3. 
The cooling fans continue to operate for about 10 seconds for cooling  cycle
.
(If you wish to turn the projector back on, you must wait until the 
projector has completed the cooling cycle and has entered standby 
mode. Once in standby mode, simply press  POWER to restart the 
projector.)
4. Turn off the main power switch. Disconnect the power cord from  the electrical outlet and the projector.
5.  Do  not  turn  on  the  projector  immediately  following  a  power  off  procedure.
Warning Indicator
v When the POWER LED indicator repeatedly blinks five (5) times,  the projector will automatically shut itself down. Please contact 
your local reseller or service center. See pages 54-55.
v When the TEMP LED is on a steady (not flashing) orange, the  projector will automatically shut itself down. Under normal  
conditions, the projector can be switched on again after it has 
cooled down. If the problem persists, you should contact your  
local dealer or our service center. See pages 54-55.
v When the POWER LED repeatedly blinks six (6) times in   conjunction with the LAMP LED blinking a single time, it  
indicates the fan has failed. Please contact your local dealer or 
our service center. See pages 54-55.
Installation 
						

							English
Adjusting the Projected Image
Adjusting the Projector’s Height
Take note of the following when setting up the projector:• The projector table or stand should be level and sturdy.
• Position the projector so that it is perpendicular to the screen.•  Ensure  the  cables  are  in  a  safe  location.  You  could  trip  over  them.
Fo cus
Zo om
A V -M uteK ey st
o
n e 
+
Re-S y ncP
owe rP owe r Lam p T
em p
E
n te r
M
en
uK eys ton e -
S
o ur
c e
C
D
B
A
1. To raise the level of the projector, lift the projector [A] and press 
the height-adjuster button  [B]. 
 
The height adjuster drops down  [C].
2. To lower the level of the projector, press the height-adjuster   button and push down on the top of the projector.
3. To adjust the angle of the picture, turn the tilt adjuster  [D] right or 
left until desired angle achieved.
Installation 
						

							English
Adjusting the Zoom / Focus
1. Use the Image-zoom control (on the projector only) to  
resize the projected image 
and screen size  [B].
2. Use the Image-focus control  (on the projector only) to 
sharpen the projected image 
[A].A
B
3. Use the keystone buttons to correct image distortion. They can be found on the remote control and on the projector’s control 
panel.
Installation 
						

							English
Control Panel
Using the Control Panel
PowerRefer to the “Power On/Off the Projector”  
section on page 15. 
Menu Press Menu to launch the on-screen display 
(OSD) menu. To exit OSD, Press 
Menu again.
▲/Keystone+ 
(Up arrow)•Adjust the image Keystone positively.
•
Navigates and changes settings in the OSD.
►/Re-Sync 
(Right arrow)•Automatically synchronizes the projector to 
the input source.
•
Navigates and changes settings in the OSD.
▼/Keystone - 
(Down arrow)•Adjust the image Keystone negatively.
•
Navigates and changes settings in the OSD.
◄/Source  
(Left arrow) •Press Source to select an input signal.
•Navigates and changes settings in the OSD.
AV-MuteMomentarily turns off / on the audio and video.
Enter
Confirm your item selection.
Power LED Green
Unit is powered on and working 
correctly
.
F l a s h i n g 
GreenUnit is on stand-by/cooling down.
Off Unit is powered off.
Lamp LED On
Lamp  not  ready—do  not  press  the 
power button.
Off Lamp is in normal state.
Temp LED On System over temperature
Off Normal state
User Controls 
						

							English0
Remote Control
Using the Remote Control
PowerRefer  to  the  “Power  On/Off  the 
Projector” section on page 15.
Laser Aim  the  remote  at  the  viewing  screen, 
press  and  hold  this  button  to  activate 
the laser pointer.
Four 
Directional 
Select Keys Use  ▲▼◄►  to  select  items  or  make 
adjustments to your selection.
PC / Mouse 
control The PC/Mouse control can be used to 
control mouse movement. The mouse 
function is enabled using the USB  
cable to connect your computer and 
the projector.
L Button Mouse left click.
R Button Mouse right click.
Page + Use this button to page up.
Page - Use this button to page down.
8Confirm your item selection.
Source Press  Source to select an input signal.
Re-Sync Automatically synchronizes the  
projector to the input source.
Keystone +/- Adjusts image distortion caused by  
tilting the projector. (±30 degrees)
Volume +/- Adjusts to increase/decrease the  
volume.
HDMI
User Controls