Optoma Projector Tx650 User Manual

							
English
Introduction

Wireless Remote Control
1.	 IR	LED
2.	 Power
3.	 Re-Sync	
4.	 Display	Mode
5.	 Keystone	Correction
6.	 Number	Buttons
7.	 Clear
8.	 Sleep	Timer
9.	 Video
10.	 S-Video	Source
11.	 Source	Lock	
12.	 VGA	Source
13.	 Color	Setting
14.	 Menu
15.	 Enter
16.	 Four	Directional	
Select	Keys
17.	 Brightness
18.	 Zoom
19.	 Display	Format
20.	 Hide
21.	 Freeze	
	21
1
	4
	5
	6
	9
2
	7
	8
	3
	15
	13
	12
	16
	14
	17
	18
	19
	20
	10	11  
						

							
English2
Installation

	To	ensure	the	projector	works	well	with	your	computer,	
please	set	the	display	mode	of	your	graphic	card	less	than	or	
equal	to	1024	X	768	resolution.	Make	sure	the	timing	of	the	
display	mode	is	compatible	with	the	projector.		Refer	to	the	
“Compatibility	Modes”	section	on	page	36.
S-Video	Output
Video	Output
DVD	Player,	Settop	Box,	HDTV	receiver5
1
6
RGB
1.........................................................................\
......................................Power	Cord2.........................................................................\
.......................................VGA	Cable3...............................................................DVI to  DVI Cable(Optional Accessory)4.....................................................Composite Video Cable(Optional Accessory) 5.....................................................................S-Video Cable (Optional Accessory) 6.....................................D-15 to RCA Adapter for YPbPr (Optional Accessory)7........................................................................RS232 Cable (Optional Accessory)
4
23
Connecting the Projector
	Due	to	the	differ-ence	in	applications	for	each	country,	some	regions	may	have	different	ac-cessories.
7   
						

							
English3
Installation

Powering On the Projector
1.	 Remove	the	lens	cap.	
2.	 Ensure	that	the	power	cord	and	signal	cable	are	securely	
connected.		The	Power	LED	will	Flash Green.
3.	 Turn	on	the	lamp	by	pressing	“Power/Standby”	button	on	
the	control	panel.	And	the	Power	LED	will	turn	Green.
The first time you use the projector, you can select your 
preferred	language	from	quick	menu	after	the	startup	screen	
display.
4. Turn on your source (computer, notebook, video player,etc.).  
The	projector	will	detect	your	source	automatically.
	If	you	connect	multiple	sources	at	the	same	time,	use	the	
“Source”	button	on	the	control	panel	or	remote	control	to	
switch.
Powering On/Off the Projector
Turn	on	the	projector	first and then the signal sources.
Power/Standby2
Lens	Cap1   
						

							
English
Installation

Warning Indicator
	 When	the	“LAMP”	indicator	lights	solid	red,	the	projector	
will	automatically	shut	itself	down.	Please	contact	your	local	
reseller	or	service	center.	See	page	38.	
	 When	the	“TEMP”	indicator	lights	solid	red	for	about	60	
seconds,	it	indicates	the	projector	has	been	overheated.	The	
projector	will	automatically	shut	itself	down.
	 Under	normal	conditions,	the	projector	can	be	switched	on	
again	after	it	has	cooled	down.		If	the	problem	persists,	you	
should	contact	your	local	dealer	or	our	service	center.	See	
page	38.	
 When the “TEMP” indicator flashes red for about 5 seconds, 
it	indicates	the	fan	failed.	Please	contact	your	local	dealer	or	
our	service	center.	See	page	38.	
Powering Off the Projector
1.		 Press	the	“Power/Standby”	button	to	turn	off	the	projector	
lamp,	you	will	see	a	message	“”	
displayed	on	the	projector’s	screen.	Press	the	“Power/
Standby” button again to confirm, otherwise the message 
will	disappear	after	5	seconds.
	 Please	note	that	if	the		key	is	pressed	instead,		the	projec-
tor	will	enter	the	“Picture	Mute”	mode	and	no	image	will	
be	displayed.		To	exit	the	“Picture	Mute”	mode,	press	the	
“Power/Standby”	button	again.	
2.	 The	cooling	fans	continue	to	operate	for	about	30	seconds	
for	cooling	cycle	and	the	Power	LED	will	turn	green.		When	
the Power LED begins flashing, the projector has entered 
standby	mode.
	 If	you	wish	to	turn	the	projector	back	on,	you	must	wait	
until	the	projector	has	completed	the	cooling	cycle	and	has	
entered	standby	mode.		Once	in	standby	mode,	simply	press	
“Power/Standby”	button	to	restart	the	projector.
3.	 Disconnect	the	power	cord	from	the	electrical	outlet	and	the	
projector.
4.	 Do	not	turn	on	the	projector	immediately	following	a	power	
off	procedure.   
						

							
English
Installation

Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt	Adjusting	
Feet
Elevator	Foot
23
Elevator	Button
The projector is equipped with an elevator foot for adjusting the 
image height.
	To	raise	the	image:
1.	 Press	the	elevator	button	.
2.	 Raise	the	image	to	the	desired	height	angle	,	then	release	
the	button	to	lock	the	elevator	foot	into	position.
3.	 Use	 to fine-tune the display angle. 
	To	lower	the	image:
1.	 Press	the	elevator	button.
2.	 Lower	the	image,	then	release	the	button	to	lock	the	eleva-
tor	foot	into	position.
3.	 Use	 to fine-tune the display angle.
3
	1  
						

							
English6
Installation
6.3"(176.1cm)
.6"(293.5cm)
6."(410.9cm)
."(469.6cm)
277.3"(704.4cm)
3." (96.8cm)
76.2"(193.6cm)
27."(322.7cm)
77."(451.8cm)
203.3"(516.3cm)
30."(774.5cm)
.'
3.'
26.3'
23.0'
6.'
.'
(1.5m)
(12.0m)
(8.0m)
(7.0m)
(5.0m)
(3.0m)
3.7"(88.1cm)
Max.38.1(96.8cm)76.2(193.6cm)127.1(322.7cm)177.9(451.8cm)203.3(516.3cm)304.9(774.5cm)Min.34.7(88.1cm)69.3(176.1cm)115.6(293.5cm)161.8(410.9cm)184.9(469.6cm)277.3(704.4cm)
Max.(WxH)30.5 x 22.9(77.4 x 58.1cm)61.0 x 45.7(154.9 x 116.2cm)101.7 x 76.3(258.2 x 193.6cm)142.3 x 106.7(361.4 x 271.1cm)162.6 x 122.0(413.0 x 309.8cm)243.9 x 182.9(619.6 x 464.7cm)
Min.(WxH)27.8 x 20.8(70.5 x 52.9cm)55.4 x 41.6(140.9 x 105.7cm)92.5 x 69.4(234.8 x 176.1cm)129.4 x 97.1(328.7 x 246.5cm)147.9 x 110.9(375.7 x 281.8cm)221.8 x 166.4(563.5 x 422.6cm)4.9(1.5m)9.8(3.0m)16.4(5.0m)23.0(7.0m)26.3(8.0m)39.4(12.0m)
Screen(Diagonal)
Screen	Size
Distance
Diagonal
Focus	Ring
Zoom	Lever
Adjusting the Projector Zoom / Focus
You	may	 turn	the	zoom	 lever	to	zoom	 in	or	 out.		 To	focus	 the	im-
age,	 rotate	 the		focus	 ring	until	 the	image	 is	clear.	 The	projector	
will  focus  at  distances  from  4.9  to  39.4  feet  (1.5  to  12.0  meters) 
with	mechanical	travel.
Adjusting Projection Image Size
This	graph	is	for	user’s	reference	only.   
						

							
English7
User Controls
Control	Panel
Control Panel & Remote Control
There are two ways for you to control the functions: Remote 
Control and Control Panel.
	Using	the	Control	Panel
	Power/Standby		
	Refer	to	the	“Power	On/Off	the	Projector”	section	on	pages	13-
14.
	Source		
	Press	“Source”	to	choose	RGB,	Component-p,	Component-i,	S-
Video,	Composite	Video	and	HDTV	sources.
	Menu	
	Press “Menu” to launch the on screen display (OSD) menu. To 
exit	OSD,	press	“Menu”	again.
	 Keystone	/
	Adjusts	image	distortion	caused	by	tilting	the	projector	(±15	
degrees).
	Four	Directional	Select	Keys
	Use								to	select	items	or	make	adjustments	to	your	
selection.
	Enter	
	Confirm your selection of items.
	Re-Sync	
	Automatically	synchronizes	the	projector	to	the	input	source.  
						

							
English
User Controls

	Using	the	Remote	Control
	 Power		
		Refer	to	the	“Power	On/Off	the	Projector”	section	on	pages	13-14.
	Re-Sync
		Automatically	synchronizes	the	projector	to	the	input	source.
	Hide
		Press	“Hide”	 to	hide	 image,	 press	again	 to	restore	 display	 of	the	image.
	 Display	Format
	Display	 the	“Display	 Format”	section	of	the	 on	screen	 display	
menu	to	select	the	desired	aspect	ratio.
	 Freeze
		Press	“Freeze”	to	pause	the	screen	image.
	 Display	Mode
		Select	the	display	mode	from	PC,	Movie,	Game,	sRGB	and	User.
	Keystone			/	
		Adjusts	image	distortion	caused	by	tilting	the	projector	(±15	
degrees).
	 Brightness
	Adjust	the	brightness	of	the	image.
	 Zoom
		Press	“D-Zoom”	button	to	zoom	in	of	an	image.
	 Four	Directional	Select	Keys	
		Use									to	select	items	or	make	adjustments	to	your	selection.
	 Enter
		Confirm your selection of items.
	 Menu		
		Press	“Menu”	to	launch	the	on	screen	display	menu.		To	exit	OSD,	press	“Menu”	again.
	 Clear
	Clear	your	selection.
	 Color	Setting
	Adjust	the	Red,	Green,	Blue,	Yellow,	Cyan	and	Magenta	colors	
for	advanced	adjustment	of	the	individual	colors.
	 Source	Lock
	Select	auto	detection	all	connector	ports	or	lock	current	connector	
port.
Remote	Control   
						

							
English
User Controls

	 Sleep	Timer
	Sets	the	countdown	timer	interval.
	 VGA
		Press	“VGA”	to	choose	VGA	connector.
	 S-Video
		Press	“S-Video”	to	choose	S-Video	source.
	 Video
		Choose	composite	video	source.  
						

							
English20
User Controls

The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.	 To	open	the	OSD	menu,	press	“Menu	”	on	the	Remote	Control	
or	Control	Panel.
2.	When	OSD	is	displayed,	use					keys	to	select	any	item	in	the	
main	menu.		While	making	a	selection	on	a	particular	page,	press	
	or	“Enter”	key	to	enter	sub	menu.
3.	Use						keys	to	select	the	desired	item	and	adjust	the	settings	
by					key.
4.	Select	the	next	item	to	be	adjusted	in	the	sub	menu	and	adjust	as	
described	above.
5.	Press	“Menu	” to confirm, and the screen will return to the main 
menu.
6.	 To	exit,	press	“Menu	”again.		The	OSD	menu	will	close	and	the	
projector	will	automatically	save	the	new	settings.
On Screen Display Menus
Main	Menu
Sub	MenuSetting