Optoma Projector Tx1080 User Manual

							
English


Introduction

Pg
Pg
F o r m at
DIVVi d eoV G A -1
S -Vi d eoH D MI
D i s p l ay
Vo l u me
1
234
567
890
M e nu
V G A -2
、、、、
E n t er
P IPS w apS RC
AVM u teR e - s y nc
S o u r ceL o ck
L a s er

Remote Control
1.	 Laser	Button
2.	 AV	Mute
3. Power (On/Off)
4.	 Re-Sync
5.	 Keystone
6.	 Page	Up
7.		
Page	Down
8. PC/Mouse Control
9.	 Mouse	Right	Click
10.	Enter
11.		
Four	Directional	Select	
Keys
12.	Display	Format
13.	Source
14.	VGA1
15.	VGA2
16.	Freeze
17.	Display	Mode
18.	Zoom	In
19.	Zoom	Out
20. Volume +/-
21.		
Mouse	Left	Click
22.	Menu
23.	Source	Lock
24.	Picture-In-Picture
25.	DVI
26.	HDMI
27.	Swap
28.	S-Video
29.	Video
3
17
4
5
6
7
8
9
10
21
22
23
24
25
26
11
12
14
15
18
19
13
21
282927
16
20
M o d elN o .:T S F N - I R 01T hed e v i cec o m p l i esw i thp a rt15oft heF CCR u l esS eei n s t r u c t i onm a n u a l.
L A S ERR A D IAT I O N-DON OTSTA REI NTOB E AM
L A S ERR A D IAT I ONDON OTSTA REI NTOB E AMC L A SSL A S ERP R O D U CTIIT h isp r o d u ctc o m p l i esw i th21C FR       
						

							


Installation

E62405SPR

DVD player, Set-top BoxHDTV receiver

 VGA,DVI

DVD player, Set-top BoxHDTV receiver

Video Output

S-Video Output

 VGA,DVI

m o l e x

MOLEX

DVD player, Set-top BoxHDTV receiver

SCE

SCE

Connecting the Projector
7
1
5
9
12
11
8
62
3
4
13
14
10        
						

							
English


Installation

Due	to	the	difference	in	applications	for	each	country,	some	regions	may	have	different	ac-cessories.
1...................................................................Network Cable (Optional Accessory)
2....................................................Audio L/R Input Cable (Optional Accessory)
3............................................................VGA Output Cable (Optional Accessory)
4.........................................................Audio Output Cable (Optional Accessory)
5.............................................................Audio Input Cable (Optional Accessory)
6.........................................................................\
.....................................RS232	Cable
7.........................................................................\
........................................USB	Cable
8....................................................Composite Video Cable (Optional Accessory)
9.....................................................................S-Video Cable (Optional Accessory)
10.....................................SCART RGB/S-Video Adapter (Optional Accessory)
11.........................................................................\
..........................VGA	Input	Cable
12.........................................................................\
DVI Cable (Optional Accessory)
13.........................................................................\
....................................Power	Cord
14.....................................................................HDMI Cable (Optional Accessory)
NoteNote        
						

							


Installation

Powering On the Projector
1.	 Remove	the	lens	cap.	
2.	 Securely	connect	the	power	cord	and	signal	cable.	When	
connected,	the	power	led	will	turn	red.
3.	 Turn	on	the	lamp	by	pressing	“	”	button	on	the	control	
panel. The power led will now flash blue.	
	 The	startup	screen	will	display	in	approximately	30	seconds.	
The first time you use the projector, you can select your 
preferred	language	from	quick	menu	after	the	startup	screen	
display.
4.	 Turn	on	your	source	that	you	want	to	display	on	the	screen	
(computer, notebook, video player, etc). The projector will 
detect	the	source	automatically	and	will	display	on	the	
screen.	If	not,	push	menu	button	and	go	to	“Options”.		Make	
sure	that	the	“Source	Lock”	has	been	set	to	“Off”.
▀■	If	you	connected	multiple	sources	at	the	same	time,	press	the	
“Source”	button	on	the	control	panel	or	direct	source	key	on	
the	remote	control	to	switch	between	inputs.
Powering On/Off the Projector
Turn	on	the	projector	first and then select the signal	sources.
////
////
21
NoteNote         
						

							
English


Installation

Warning Indicator
▀■	When	the	“LAMP”	indicator	led	is	lit	red,	the	projector	will	
automatically	shut	down.	Please	call	the	nearest	Optoma	
facility	for	assistance.	
▀■ When the “TEMP” indicator flashes red, it indicates the 
projector	has	overheated.	The	projector	will	shut	down	auto-
matically.	
Under	normal	conditions,	the	projector	can	be	switched	on	
again	after	it	has	cooled	down.
▀■ When the “LAMP” indicator flashes red, it indicates the fan 
has	failed.
Powering Off the Projector
1.	 Press	the	“”	button	to	turn	off	the	projector.	The	following	
message	will	be	displayed	on	the	screen.	
Press	the	“” button again to confirm the shut down. If 
the	button	is	not	pressed,	the	message	will	disappear	in	5	
seconds.
2.	 The	cooling	fans	continue	to	operate	for	about	60	seconds	for	
cooling cycle and the Power LED will flash blue.  When the 
lights	solid	red,	the	projector	has	entered	standby	mode.
If	you	wish	to	turn	the	projector	back	on,	you	must	wait	
until	the	projector	has	completed	the	cooling	cycle	and	has	
entered	standby	mode.		Once	in	standby	mode,	simply	press	
“”	button	to	restart	the	projector.
3.	 Disconnect	the	power	cord	from	the	electrical	outlet	and	the	
projector.
4.	 Do	not	turn	on	the	projector	immediately	following	a	power	
off	procedure.
Contact	the	nearest	service	center	if	the	projector	displays	these	symptoms.	See	page	55	for	more	information.
NoteNote       
						

							


Installation

Adjusting the Projected Image
Adjusting the Projector’s Height
Tilt-Adjustment	Feet
Elevator	Feet
The projector is equipped with elevator feet for adjusting the 
image height.
	To raise the image:
1.	 Press	the	elevator	button	.	
2.		
Raise	the	image	to	the	desired	height	angle	,	then	release		
the	button	to	lock	the	elevator	feet	into	position.
3.	 Use	screw	in	feet	 to fine-tune the display angle. 
	To lower the image:
1.	 Press	the	elevator	button.
2.		
Lower	the	image,	then	release	the	button	to	lock	the	eleva-
tor	feet	into	position.
3.	 Use	screw	in	feet	 to fine-tune the display angle.
Elevator	Button1
3
2       
						

							
English


Installation

///
/

Focus	Ring
Zoom	Lever
Adjusting the Projector’s Zoom / Focus
Turn	the	Zoom	Lever	to	zoom	in	or	zoom	out.	To	focus	the	
image,	turn	the	focus	ring	until	you	see	a	clear	image.	The	
projector will focus at distances from 4.9 to 41.0 feet (1.5 to 
12.5 meters) and the projection screen size from 0.68m~7.75m 
(26.77”~305.22”) at 16:9 mode with mechanical travel.
Adjusting Projection Image Size
WidthHeight
Diagonal
Screen
Screen
Projection Distance (D)
Projection Distance (D)
Screen (W)
Screen (H)
Offset (Hd)
Top View
	This	graph	is	for	user’s	reference	only.
Diagonallength (inch) size of 16:9 Screen
Screen Size W X H (16:9)Projection distance (D)Offset(Hd)(m)(feet)(m)(feet)widetelewidetelewidetelewidetele(m)(feet)270.600.341.971.111.111.333.644.370.120.40370.810.462.661.501.501.804.925.910.160.54501.110.623.642.042.052.466.738.070.220.74601.340.754.382.462.472.968.109.720.270.89701.550.875.092.862.873.449.4211.300.311.03801.781.005.853.293.283.9410.7612.910.361.18901.991.126.533.683.694.4312.1114.530.401.331002.221.257.274.094.104.9213.4516.140.451.471202.661.508.724.914.925.9016.1419.370.541.771503.321.8710.906.146.157.3820.1824.210.672.212004.322.4914.178.188.209.8426.9032.280.902.943006.653.7421.8112.2712.3014.7640.3548.431.354.42       
						

							


User Controls

Control Panel & Remote Control
There are two ways for you to control the functions: Control 
Panel and Remote Control.
Using	the	Control	Panel
////
 PowerRefer to the “Power On/Off the Projector” section	on	pages	14-15.
SourcePress	“Source”	to	select	the	input	signal	
source.
MenuPress	“Menu”	to	launch	the	on-screen	
display (OSD) menu. To exit OSD, Press 
“Menu”	again.
KeystoneAdjust	image	distortion	caused	by	tilting	
the	projector.
Four Direc-
tional Select 
Keys
Use								to	select	items	or	make	
adjustments	to	your	selection.
EnterConfirm your item selection.
Re-Sync	Automatically	synchronize	the	projector	to	
the	input	source.       
						

							
English


User Controls

Pg
Pg
F o r m at
DIVVi d eoV G A -1
S -Vi d eoH D MI
D i s p l ay
Vo l u me
1
234
567
890
M e nu
V G A -2
、、、、
E n t er
P IPS w apS RC
AVM u teR e - s y nc
S o u r ceL o ck
L a s er

Using	the	Remote	Control
 PowerRefer to the “Power On/Off the Projector” section	on	pages	14-15.
Laser	Aim	the	remote	at	the	viewing	screen,	press	
and	hold	this	button	to	activate	the	laser	
pointer.
AV Mute Momentarily turn on/off the audio and 
video.
Re-syncAutomatically	synchronize	the	projector	to	
the	input	source.
DisplaySelect	the	display	mode	from	Presentation,
Bright,	Movie,	sRGB,	User1	and	User2.
FreezePress	“Freeze”	to	pause	the	screen	image.	
Press	this	button	again	to	unlock.
KeystoneAdjust	image	distortion	caused	by	tilting	
the	projector.
 Zoom InZoom	in	to	magnify	the	image.
 Zoom OutZoom	out	to	reduce	the	image.
Volume +/-Adjust to increase/decrease the volume.
Pg Page UpUse	this	button	to	page	up.
Pg Page 
Down
Use	this	button	to	page	down.
Mouse 
Control
The PC/Mouse control can be used to con-
trol	mouse	movement.	The	mouse	function	
is	enabled	using	the	USB	cable	to	connect	
your	computer	and	the	projector.
、、 L ButtonMouse	left	click.
、、 R ButtonMouse	right	click.
MenuDisplay	or	exit	the	on-screen	display	menus	
for	projector.
EnterConfirm your item selection.
Four Direc-
tional Select 
Keys
Use	to	select	items	or	make	
adjustments	to	your	selection.
M o d elN o .:T S F N - I R 01T hed e v i cec o m p l i esw i thp a rt15oft heF CCR u l esS eei n s t r u c t i onm a n u a l.
L A S ERR A D IAT I O N-DON OTSTA REI NTOB E AM
L A S ERR A D IAT I ONDON OTSTA REI NTOB E AMC L A SSL A S ERP R O D U CTIIT h isp r o d u ctc o m p l i esw i th21C FR       
						

							
0

User Controls

Source LockSelect	auto	detection	all	connector	ports	or	
lock	current	connector	port.
FormatDisplay	the	“Aspect	Ratio”	section	of	the	
on-screen	display	menu	to	select	the	desired	
aspect	ratio.
PIPPress	“PIP”	to	open	the	PIP	window.	Main	
screen	is	large;	PIP	screen	is	small	and	dis-
playes	in	the	corner	of	the	main	screen.
SwapPress	“Swap”	to	swap	the	main	screen	and	
PIP	screen.
SRCSelect	the	input	signal	source	at	the	next	
terminal.
DVIPress	“DVI”	to	choose	digital	signal	source	
from	DVI	connector.
VideoPress	“Video”	to	choose	Composite	video	
source.
VGA-1Press	“VGA1”	to	choose	source	from
VGA1-In/SCART connector.
VGA-2Press	“VGA2”	to	choose	source	from
VGA2-In/SCART connector.
S-VideoPress	“S-Video”	to	choose	S-video	source.
HDMIPress	“HDMI”	to	choose	HDMI1	source.
	
Pg
Pg
F o r m at
DIVVi d eoV G A -1
S -Vi d eoH D MI
D i s p l ay
Vo l u me
1
234
567
890
M e nu
V G A -2
、、、、
E n t er
P IPS w apS RC
AVM u teR e - s y nc
S o u r ceL o ck
L a s er
M o d elN o .:T S F N - I R 01T hed e v i cec o m p l i esw i thp a rt15oft heF CCR u l esS eei n s t r u c t i onm a n u a l.
L A S ERR A D IAT I O N-DON OTSTA REI NTOB E AM
L A S ERR A D IAT I ONDON OTSTA REI NTOB E AMC L A SSL A S ERP R O D U CTIIT h isp r o d u ctc o m p l i esw i th21C FR