Optoma Projector Pro360w User Manual

							21English
User Controls
The Projector has multilingual On-screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1. To open the OSD menu, press “Menu” on the Remote Control or 
Projector Keypad.
2  When OSD is displayed, use   keys to select any item in the 
main menu. While making a selection on a particular page, press 
 or “Enter” key to enter sub menu.
3. Use   keys to select the desired item and adjust the settings 
using   key.
4. Select the next item to be adjusted in the sub menu and adjust as 
described above.
5. Press “Enter” to confirm, and the screen will return to the main 
menu.
6. To exit, press “MENU” again. The OSD menu will close and the 
projector will automatically save the new settings.
On-screen Display Menus
Main Menu
Sub Menu
Settings        
						

							22English
User Controls
Menu Tree
Main Menu Sub MenuSettings
ImageDisplay Mode
Brightness-50~50
Contrast -50~50
Sharpness 1~15
Color -50~50
Tint -50~50
Advanced Gamma Film / Video / Graphics / Standard
0~10
Color Temp. Warm / Medium / Cold
Color Settings
Color Space AUTO / RGB / YUV
AUTO / RGB (0-255) / RGB (16-235) / YUV
Input Source VGA / Video / S-Video / HDMI
Exit
DisplayFormat 4:3 / 16:9-I / 16:9-II / Native / AUTO
4:3 / 16:9 or 16:10 / LBX / Native / AUTO
Edge Mask 0~10
Zoom -5~25
H Image Shift -50~50
V Image Shift -50~50
V Keystone -40~40
3D 3D Mode Off / DLP-Link / IR
3D Sync. Invert On / Off
Exit
SetupLanguage
Projection
Menu Location
Screen Type 16:10 / 16:9
Signal Automatic On / Off
Phase (VGA) 0~31
Frequency (VGA) -5~5
H. Position (VGA) -5~5
V. Position (VGA) -5~5
Exit ³
Security Security On / Off
Security Timer Month / Day / Hour
Change Password ³
Exit Presentation / Bright / Movie / sRGB / 
Blackboard / Classroom / User / 3D
#1
#1
BrilliantColor™ 
Red Gain / Green Gain / Blue Gain / Red 
Bias / Green Bias / Blue Bias / Cyan / 
Magenta / Yellow / Reset / Exit
#6
#2
#3
#4
English / Deutsch / Français / Italiano / 
Español / Português / Svenska / 
Nederlands / Norsk/ Dansk / Polski / 
Suomi /  Jmkkdbc  / 
0  / Magyar / 
ý eština /  6
						

							23English
User Controls
	Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are using.
	(#1) “Color” and “Tint” are only supported in Video mode. 
	(#2) For XGA model only.
	(#3) For WXGA model only. 16:9 or 16:10 depend on “Screen Type” setting.
	(#4)  “3D Sync Invert” is only available when 3D is enabled and this mode 3D is for DLP link glass only. 
	(#5) “Signal” is only supported in Analog VGA (RGB) signal.
	(#6) For HDMI Source only.
Main Menu Sub Menu Settings
SetupProjector ID0~99
Mute On / Off
Volume 0~10
Advanced Logo
Logo Capture
Closed Captioning Off / CC1 / CC2
Exit
OptionsSource Lock On / Off
High Altitude On / Off
Information Hide On / Off
Keypad Lock On / Off
Background Color Black / Red / Blue / Green / White
Test Pattern None / Grid / White Pattern
Advanced Direct Power On On / Off
Auto Power Off (min.) 0~180
Sleep Timer (min.) 0~995
Power Mode (Standby) Eco. / Active
Exit
Lamp Settings Lamp Hours
Lamp Reminder On / Off
Brightness Mode STD/Bright
Lamp Reset Yes / No
Exit
Reset Optoma / Neutral / User 
						

							24English
User Controls
IMAGE
 Display Mode
There are many factory presets optimized for various types of  
images.
 Presentation: Good color and brightness from PC input.
 Bright: Maximum brightness from PC input.
 Moive: For home theater.
 sRGB: Standardised accurate color.
 Blackboard: This mode should be selected to achieve optimum 
color settings when projecting onto a blackboard (green).
 Classroom: This mode is recommended for projecting in a 
classroom.
 User: User’s settings.
 3D: Recommand setting for 3D mode enabled. Any further ad-
justments by the user in 3D will be saved in this mode for further 
use.
  Brightness
Adjust the brightness of the image.
  Press the  to darken image.
  Press the  to lighten the image.
 Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. 
  Press the  to decrease the contrast.
  Press the  to increase the contrast.     
						

							25English
User Controls
 Sharpness
Adjust the sharpness of the image.
  Press the  to decrease the sharpness.
  Press the  to increase the sharpness. 
  Color
Adjust a video image from black and white to fully saturated color .
  Press the  to decrease the amount of saturation in the image.
  Press the  to increase the amount of saturation in the image. 
  Tint
Adjust the color balance of red and green.
  Press the  to increase the amount of green in the image.
  Press the  to increase the amount of red in the image. 
	“Color” and “Tint” functions are only supported under Video mode.       
						

							26English
User Controls
IMAGE | Advanced
 Gamma
This allows you to choose a degamma table that has been  
fine-tuned to bring out the best image quality for the input.
  Film: for home theater.
  Video: for video or TV source.
  Graphics: for image source.
  Standard: for PC or computer source.
  BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and 
system level enhancements to enable higher brightness while 
providing true, more vibrant colors in picture. The range is from 
“0” to “10”. If you prefer a stronger enhanced image, adjust toward 
the maximum setting. For a smoother, more natural image, adjust 
toward the minimum setting.
 Color Temp
If set to cold temperature, the image looks more blue. (cold image)
If set to warm temperature, the image looks more red.
(warm image)
 Color Settings
Press  into  the  next  menu  as  below  and  then  use  or    to 
select item.
   Red/Green/Blue/Cyan/Magenta/Yellow: Use  or  to select 
Red, Green, Blue, Cyan, Magenta and Yellow Colors.
   Reset: Choose “Yes” to return the factory default settings for 
color adjustments.     
						

							27English
User Controls
 Color Space
Select an appropriate color matrix type from AUTO, RGB or YUV.
 Input Source
Use this option to enable / disable input sources. Press  to enter 
the sub menu and select which sources you require. Press “Enter” 
to finalize the selection. The projector will not search for inputs that 
are not selected. 
						

							28English
User Controls
DISPLAY
 Format
Use this function to choose your desired aspect ratio.
SVGA/XGA
  4:3: This format is for 4×3 input sources.
  16:9-I: This format is for 16×9 input sources, like HDTV and 
DVD enhanced for Wide screen TV. (576i/p)
  16:9-II: This format is for 16×9 input sources, like HDTV and 
DVD enhanced for Wide screen TV. (480i/p)
  Native: This format displays the original image without any 
scaling.
  AUTO: Automatically selects the appropriate display format. 
When input is 4:3, the image is displayed as 4:3. When input is 
16:9 above, the image is displayed as 16:9- I
Aspect ratio
(source detected) Resize image (SVGA)Resize image (XGA)
4:3800 x 600 center1024 x 768 center
16:9-I800 x 450 center1024 x 576 center
16:9-II800 x 480 center854 x 480 center
Native
No resize image, 1:1 mapping and 
centered. This format shows the 
original image without scaling. 
  
						

							29English
User Controls
WXGA
  4:3: This format is for 4×3 input sources.
  16:9: This format is for 16×9 input sources, like HDTV and DVD 
enhanced for Wide screen TV. 
  16:10: This format is for 16×10 input sources, like widescreen 
laptops.
  LBX: This format is for non-16x9, letterbox source and for users 
who use external 16x9 lens to display 2.35:1 aspect ratio using 
full resolution.
  Native: This format displays the original image without any 
scaling.
  AUTO: Automatically selects the appropriate display format.
16:10 Screen480i/p576i/p1080i/p720pPC
4:31066 x 800 center
16:101280 x 800 center
LBX1280 x 960 center, then get the central 1280 x 800 image to display
Native1:1 mapping centered.
1:1 map-ping display 1280 x 800
1280 x 720 center
1:1 mapping centered.
16:9 Screen480i/p576i/p1080i/p720pPC
4:3960 x 720 center
16:91280 x 720 center
LBX1280 x 960 center, then get the central 1280 x 720 image to display
Native1:1 mapping centered.
1:1 map-ping display 1280 x 720
1280 x 720 center
1:1 mapping centered.
	16:9 or 16:10 depend on “Screen Type” setting. 
						

							30English
User Controls
	Each I/O has different setting of “Edge Mask”.
	“Edge Mask” and “Zoom” can’t work at same time.
 Edge Mask
Edge mask function removes the noise in a video image. Edge 
mask the image to remove video encoding noise on the edge of 
video source.
 Zoom
  Press the  to reduce the size of an image.
  Press the  to magnify an image on the projection screen.
  H Image Shift
Shift the projected image position horizontally. 
 V Image Shift
Shift the projected image position vertically. 
 V Keystone
Press the  or  to adjust image distortion vertically. If the image 
looks trapezoidal, this option can help make the image rectangular .