Optoma Projector Hd8600 User Manual

English

Introduction
Backup Remote Control
1. Power Off
2. Power On
3. Enter
4.  
Four Directional Select 
Keys
5. Source
6. Menu
1
3
56
2
4
Before using the 
remote control for the 
first time, remove the 
transparent insulation 
tape.
NoteNote
3VOLTSCR2025
Coin Cell Battery Replacement
MnO2-LiCELL3VOLTSJAPANHCR2025
3VOLTSCR2025
M3VOLTSCR2025
12
34
NoteNote
Backup remote  
control is  
magnetically attached 
to the back I/O of the 
projector.      


Installation
Due to the difference 
in applications for each 
country, some regions 
may have different  
accessories.
1.................................................................... VGA Input Cable (Europe Only)
2. ......................................................... DVI/HDMI Cable (Optional Accessory)
3. ........................................................................\
........................... Power Cord
4. .................................................................

English

Installation
Due to the difference in applications for each 
country, some regions 
may have different  
accessories.
1....................... Composite Video Cable (Not Available in European Version)
2. .............................. RCA Component Cable for YPbPr (Optional Accessory)
3. ........................................................................\
... HDMI Cable (Europe Only)
4. ........................................................................\...

14
Installation
Caution 
• Do not shake or place excessive pressure on the  
projector or the lens components as the projector and 
lens components contain precision parts.
• Before removing or installing the lens, be sure to turn off  the projector, wait until the cooling fans stop, and turn 
off the main power switch.
• Do not touch the lens surface when removing or   
installing the lens.
• Keep fingerprints, dust or oil off the lens surface.   Do not scratch the lens surface.
• Work on a level...

English
15
Installation
3. Pull out the existing 
lens slowly.
Installing the New Lens
1. Align the notches and  
correctly position 
the electrical contact 
pad as shown in the 
picture.
2. Rotate the lens  
clockwise until you 
feel it click into place.
Pin of 
IRIS
Pin of IRIS should be in 
the direction as shown 
in the picture.
NoteNote      


Installation
Powering On the Projector
1. Remove the lens cap. 
2. Securely connect the power cord and signal cable. When 
connected, the power led will turn red.
3. Turn on the lamp by pressing “” button on the rear of 
the projector or  “
” on the remote control.  
The power led  “
” will now flash blue.  
 The startup screen will display in approximately 30 seconds. 
The first time you use the projector, you can select your 
preferred language from quick menu after the startup screen...

English

Installation
Warning Indicator
▀■ When the “LAMP” indicator led “” is lit orange, the  
projector will automatically shut down. Please call the   
nearest Optoma facility for assistance. 
▀■
  When the “TEMP” indicator “” turns red, it indicates the  
projector has overheated. The projector will shut down   
automatically.  Under normal conditions, the projector can be switched on 
again after it has cooled down.
▀■
  When the “TEMP” indicator “” flashes red, it indicates the 
fan has...


Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
Tilt-Adjustment Feet
The projector is equipped with elevator feet for adjusting 
the image height.
 To raise the image:
Use screw in foot to raise the image to the desired height 
angle and fine-tune the display angle 
. 
 To lower the image:
Use screw in foot to lower the image to the desired height 
angle and fine-tune the display angle 
. 
1      

English
19
Installation
Horizontal Lens 
Shift Lever
Adjusting Projected Image Position 
Using PureShift
The PureShift feature provides a lens shift function that can be 
used to adjust the position of the projected image either  
horizontally or vertically within the range detailed below.   
PureShift is a unique system that provides lens shift while   
maintaining a much higher ANSI contrast ratio than traditional 
lens shift systems.
Vertical Lens 
Shift Lever
▀■ Adjusting the vertical image position...

20
Installation
Screen Height(H)
100%
H x 10% H x 30%
H x 20%
H x 60%
Distance (L)
Screen
▀■	
Adjusting the horizontal image position
With	the	lens	in	the	center	position	the	horizontal	image		
position	can	be	adjusted	to	the	left	or	right	by	up	to	a	maximum	
of	10%	of	the	half	image	width.	Note	that	the	maximum		
horizontal	image	height	adjustment	can	be	limited	by	the		
vertical	image	position.	For	example	it	is	not	possible	to	achieve	
the	maximum	horizontal	image	position	if	the	vertical	image...