Optoma Projector Ep910 User Manual

11English

Installation

Connect the Video
 Due to the differ-   ence in applica-     tions for each      country, some      regions may have    different      accessories.
1. .............................................................................................................Power Cord2. ......................................................................RCA Component Cable for YPbPr3. ...........................................................................SCART RGB/S-Video Adaptor 4....

12English

Installation

Powering On the Projector
1.  Remove the lens cap. 
2.  Ensure that the power cord and signal cable are securely 
connected.  The Power LED will turn green.
3.  Turn on the lamp by pressing “” button on the control 
panel. And the Power LED will turn blue.
4.  Turn on your source (computer, notebook, video player,etc.).  
The projector will detect your source automatically within  
“Management-II” menu, check that “Source Detect” has 
been set to “Auto”.
 If the screen...

13English

Installation

Warning Indicator
  When the “LAMP” indicator lights solid red, the projector 
will automatically shut itself down. Please contact your local 
reseller or service centre. See page 40. 
  When the “TEMP” indicator lights solid red, it indicates the 
projector has overheated. The projector will automatically 
shut itself down.
  Under normal conditions, the projector can be switched on 
again after it has cooled down.  If the problem persists, you 
should contact your local...

14English

Installation

Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt Adjusting Feet
Elevator Foot
Elevator Button
The projector is equipped with elevator feet for adjusting the 
image height.
 To raise the image:
1.  Press the elevator button .
2.  Raise the image to the desired height angle , then release  
  the button to lock the elevator foot into position.
3.  Use screw in feet  to fine-tune the display angle. 
 To lower the image:
1.  Press the elevator button.
2....

15English

Installation

61.5"
(156.3cm) 102.5"
(260.4cm) 143.5"
(364.6cm) 184.5"
(468.8cm) 246.1"
(625.0cm)
36.9" 
(93.8cm) 73.8"
(187.5cm) 123.0"
(312.5cm) 172.2"
(437.5cm) 221.5"
(562.5cm) 295.3"
(750.0cm)
4.9'
39.4' 29.5' 23.0' 16.4' 9.8'
(1.5m)
(12.0m) (9.0m) (7.0m) (5.0m)
(3.0m) 30.8"
(78.1cm)

Diagonal
Focus Ring
Zoom Lever
Adjusting the Projector Zoom / Focus
You may turn the zoom lever to zoom in or out.  To focus the im-...

16English

User Controls

Remote ControlControl Panel
Control Panel & Remote Control
There are two ways for you to control the functions: Remote 
Control and Control Panel.
Using the Control Panel
PowerRefer to the “Power On/Off the Projector” section 
on pages 12-13.
SourcePress “Source” to select an input signal.
MenuTurns the menu On or Off.
Four Direc-
tional Select 
Keys
Use        to navigate through the menus.
EnterConfirm your item selection.
Re-Sync Automatically synchronizes the projector to...

17English

User Controls

Using the Remote Control
PowerRefer to the “Power On/Off the Projector” section 
on pages 12-13.
Re-Sync Automatically synchronizes the projector to the 
input source.
KeystoneAdjusts image distortion caused by tilting the 
projector (±16 degrees).
Zoom InZoom in to magnify the image.
Zoom OutZoom out to reduce the image.
Page UpUse this button to page up.
Page DownUse this button to page down.
Mouse Right 
Click
Mouse right click.
Mouse Left 
Click
Mouse left click....

18English

User Controls

S-VideoChoose S-video source.
ComponentChoose component source.
DVIChoose DVI-I source.
VGAChoose VGA source. 

19English

User Controls

The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.  To open the OSD menu, press “Menu” on the Remote Control  
  or Control Panel.
2. When OSD is displayed, use     keys to select any item in the  
  main menu.  While making a selection on a particular page, press  
  key to enter sub menu.
3. Use      keys to select the...

20English

User Controls

Menu Tree