Optoma Projector Ep1080 User Manual

English


Introduction

Pg
Pg
F o r m at
DIVVi d eoV G A -1
S -Vi d eoH D MI
D i s p l ay
Vo l u me
1
234
567
890
M e nu
V G A -2
、、、、
E n t er
P IPS w apS RC
AVM u teR e - s y nc
S o u r ceL o ck
L a s er

Remote Control
1.	 Laser	Button
2.	 AV	Mute
3. Power (On/Off)
4.	 Re-Sync
5.	 Keystone
6.	 Page	Up
7.		
Page	Down
8. PC/Mouse Control
9.	 Mouse	Right	Click
10.	Enter
11.		
Four	Directional	Select	
Keys
12.	Display	Format
13.	Source
14.	VGA1
15.	VGA2
16.	Freeze
17.	Display	Mode
18.	Zoom	In...



Installation

E62405SPR

DVD player, Set-top BoxHDTV receiver

 VGA,DVI

DVD player, Set-top BoxHDTV receiver

Video Output

S-Video Output

 VGA,DVI

m o l e x

MOLEX

DVD player, Set-top BoxHDTV receiver

SCE

SCE

Connecting the Projector
7
1
5
9
12
11
8
62
3
4
13
14
10        

English


Installation

Due	to	the	difference	in	applications	for	each	country,	some	regions	may	have	different	ac-cessories.
1...................................................................Network Cable (Optional Accessory)
2....................................................Audio L/R Input Cable (Optional Accessory)
3............................................................VGA Output Cable (Optional Accessory)
4.........................................................Audio Output...



Installation

Powering On the Projector
1.	 Remove	the	lens	cap.	
2.	 Securely	connect	the	power	cord	and	signal	cable.	When	
connected,	the	power	led	will	turn	red.
3.	 Turn	on	the	lamp	by	pressing	“	”	button	on	the	control	
panel. The power led will now flash blue.	
	 The	startup	screen	will	display	in	approximately	30	seconds.	
The first time you use the projector, you can select your 
preferred	language	from	quick	menu	after	the	startup	screen	
display.
4.	 Turn	on	your	source	that	you...

English


Installation

Warning Indicator
▀■	When	the	“LAMP”	indicator	led	is	lit	red,	the	projector	will	
automatically	shut	down.	Please	call	the	nearest	Optoma	
facility	for	assistance.	
▀■ When the “TEMP” indicator flashes red, it indicates the 
projector	has	overheated.	The	projector	will	shut	down	auto-
matically.	
Under	normal	conditions,	the	projector	can	be	switched	on	
again	after	it	has	cooled	down.
▀■ When the “LAMP” indicator flashes red, it indicates the fan 
has	failed.
Powering...



Installation

Adjusting the Projected Image
Adjusting the Projector’s Height
Tilt-Adjustment	Feet
Elevator	Feet
The projector is equipped with elevator feet for adjusting the 
image height.
	To raise the image:
1.	 Press	the	elevator	button	.	
2.		
Raise	the	image	to	the	desired	height	angle	,	then	release		
the	button	to	lock	the	elevator	feet	into	position.
3.	 Use	screw	in	feet	 to fine-tune the display angle. 
	To lower the image:
1.	 Press	the	elevator	button.
2.		
Lower	the	image,...

English


Installation

///
/

Focus	Ring
Zoom	Lever
Adjusting the Projector’s Zoom / Focus
Turn	the	Zoom	Lever	to	zoom	in	or	zoom	out.	To	focus	the	
image,	turn	the	focus	ring	until	you	see	a	clear	image.	The	
projector will focus at distances from 4.9 to 41.0 feet (1.5 to 
12.5 meters) and the projection screen size from 0.68m~7.75m 
(26.77”~305.22”) at 16:9 mode with mechanical travel.
Adjusting Projection Image Size
WidthHeight
Diagonal
Screen
Screen
Projection Distance (D)
Projection...



User Controls

Control Panel & Remote Control
There are two ways for you to control the functions: Control 
Panel and Remote Control.
Using	the	Control	Panel
////
 PowerRefer to the “Power On/Off the Projector” section	on	pages	14-15.
SourcePress	“Source”	to	select	the	input	signal	
source.
MenuPress	“Menu”	to	launch	the	on-screen	
display (OSD) menu. To exit OSD, Press 
“Menu”	again.
KeystoneAdjust	image	distortion	caused	by	tilting	
the	projector.
Four Direc-
tional Select 
Keys
Use...

English


User Controls

Pg
Pg
F o r m at
DIVVi d eoV G A -1
S -Vi d eoH D MI
D i s p l ay
Vo l u me
1
234
567
890
M e nu
V G A -2
、、、、
E n t er
P IPS w apS RC
AVM u teR e - s y nc
S o u r ceL o ck
L a s er

Using	the	Remote	Control
 PowerRefer to the “Power On/Off the Projector” section	on	pages	14-15.
Laser	Aim	the	remote	at	the	viewing	screen,	press	
and	hold	this	button	to	activate	the	laser	
pointer.
AV Mute Momentarily turn on/off the audio and 
video.
Re-syncAutomatically	synchronize...

0

User Controls

Source LockSelect	auto	detection	all	connector	ports	or	
lock	current	connector	port.
FormatDisplay	the	“Aspect	Ratio”	section	of	the	
on-screen	display	menu	to	select	the	desired	
aspect	ratio.
PIPPress	“PIP”	to	open	the	PIP	window.	Main	
screen	is	large;	PIP	screen	is	small	and	dis-
playes	in	the	corner	of	the	main	screen.
SwapPress	“Swap”	to	swap	the	main	screen	and	
PIP	screen.
SRCSelect	the	input	signal	source	at	the	next	
terminal.
DVIPress	“DVI”	to	choose	digital	signal...