Optoma Projector Eh500 User Manual

							English
31
User Controls
Display | 3D
 3D Mode
 
DLP Link: Select DLP Link to use optimized settings for DLP Link 3D Glasses.
 
VESA 3D: Select VESA 3D to use optimized settings for IR-based 3D images.
 3D2D
Press ◄ or ► to select projector display 3D content in 2D (Left) 
or 2D(Right) without using 3D glasses to enjoy 3D content. 
This setting can also be used for dual projector passive 3D 
installations.
 3D Format
 
Auto: When a 3D identification signal is detected, the 3D format is selected automatically. (For HDMI 1.4 3D sources only)
 
SBS: Display 3D signal in Side-by-Side format.
 
Top and Bottom: Display 3D signal in Top and Bottom format.
 
Frame Sequential: Display 3D signal in Frame Sequential format.
 3D Sync. Invert
Press ◄ or ► to enable or disable the 3D Sync invert function to 
invert images.      
						

							32
User Controls
 Language
Enter the Language menu. Select the multilingual OSD menu.  
See page 34 for more information.
 Projection
Select projection method:
  Front Desktop
The factory default setting.
  Rear Desktop
When you select this function, the projector reverses the image 
so you can project from behind a translucent screen.
  Front Ceiling
When you select this function, the projector turns the image 
upside down for ceiling-mounted projection.
  Rear Ceiling
When you select this function, the projector reverses and turns 
the image upside down at same time. You can project from 
behind a translucent screen with ceiling mounted projection.
 Menu Location
Choose the menu location on the display screen.
 Security
Enter the Security menu. Access the projector’s security features.  
See pages 35-37 for more information.
Setup     
						

							English
33
User Controls
 Projector ID
Select a two digit projector ID from 00 through 99.
 Audio Settings
Enter the Audio menu. Set audio level properties. See page 38 
for more information.
 Advanced
Enter the Advanced menu. Select the screen display during 
startup. See page 39 for more information.
 Network
Allows access to controls for web, PJ-Link, and IP commands. 
See page 40 for more information.      
						

							34
User Controls
 Language
Choose the multilingual OSD menu. Press “ENTER” into the sub 
menu and then use the Left (◄) or Right (►) key to select your 
preferred language.
Setup | Language     
						

							English
35
User Controls
Setup | Security
 Security Setting
Enable or disable the security password.
 
On—the current password is required to power on the projector and access the Security menu.
 
Off—no password is required after system power up.
When security is enabled, the following screen displays at startup 
and before access to the Security menu is allowed:NoteNote
The default password: 1, 2, 3, 4, 5.      
						

							36
User Controls
 Security Timer
Enter the Security Timer sub menu.
Enter the Months, Days, and hours that the projector can be 
used without entering the password. Exiting to the Setup menu 
activates the Security Timer.
Once activated, the projector requires a password on the 
specified dates and times to allow power on and access to the 
security menu.
If the projector is in use and the Security Timer is active, the 
following screen displays 60 seconds before the password is 
required.     
						

							English
37
User Controls
 Change Password
Use this submenu to change the security password for the 
projector.
1. Select Change Password from the Security submenu. The 
Confirm Change Password dialog box displays.
2. Select Yes.
3. Enter the default password     .
A second password screen displays.
4. Enter the new password twice for verification.
NoteNote
If the incorrect password is entered three times, the device auto shutdowns after 10 seconds.
NoteNote
If the new passwords do not match, the password screen redisplays.      
						

							38
User Controls
 Internal Speaker
Off—turn off the internal speaker.
On–turn on the internal speaker.
 Mute
Toggle the audio on or off.
Off—the speaker volume and audio out are turned on.
On–the speaker volume and audio out are turned off. 
 Volume
Press ◄ to decrease the volume.
Press ► to increase the volume.
 Audio Input
Press ◄► to select audio source input.
Setup |  
Audio Settings     
						

							English
39
User Controls
Setup | Advanced
 Logo
Select the screen to display during startup. 
Optoma—the supplied default startup screen.
Neutral— is Background Color.
User—customized screen capture using the Logo Capture function.
 Logo Capture
Capture a displayed screen to use as the startup screen.
1. Display the desired screen on the projector.
2. Select Logo Capture from the Advanced menu. 
A confirmation screen displays.
3. Select OK. Screen capture in progress will display.
When finished, Screen capture Succeeded will display.
The captured screen is saved as User in the logo menu.
 Closed Captioning
Select the screen to display closed captioning
Off–the supplied default setting.
CC1/CC2–closed captioning type select.
NoteNote
Only one startup screen can be saved at once. Subsequent captures  overwrite previous files limited in 1920 x 1200 (Refer Appendices Timing Table)      
						

							40
User Controls
 LAN Settings
Enter the LAN Settings menu. See page 41 for more 
information.
 Control Settings
Enter the Control Settings menu. See page 42 for more 
information.
Setup | Network