Optoma Projector Eh2060 User Manual

							English

User Controls
On the PC (Laptop), select Start -> Control Panel ->  
Network Connections. 
                               
 
                               
Right click on your Local Area Connection and select Properties.  
                              
In the Properties window, select the General tab, and select  
Internet Protocol (TCP/IP).
Click Properties. 
                              
2.
3.
4.
5.      
						

							
User Controls
6. Fill in the IP address and Subnet mask, then press OK.  
7. Press the Menu button on the projector.
8. Select OSD-> SETUP-> Network-> Enabled.
9. Input the following:
 IP Address:  10.10.10.10
 Subnet Mask:  255.255.255.0
 Gateway:  0.0.0.0
 DNS:  0.0.0.0
10. Press Apply (Enter) to confirm settings. 11. Open a web browser.
12. In the Address bar, input the IP address: 10.10.10.10. 
13. Press Apply.
The projector is setup for remote management. The Network function 
displays as follows.
       
						

							English

User Controls
14. Based on network web-page for the input-string in [tools] tab, the 
limitation for Input-Length is in the below list (“space” and the other 
punctuation key included): 
CategoryItemInput-Length (characters)
Crestron Control IP Address
15
IP ID 2
Port 5
Projector Projector Name 10
Location
9
Assigned To 9
Network Configuration DHCP (Enabled) (N/A)
IP Address
15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User Password Enabled
(N/A)
New Password 15
Confirm 15
Admin Password Enabled
(N/A)
New Password 15
Confirm 15
 
For more  
information, please visit 
http://www.crestron.
com
NoteNote      
						

							
User Controls
 Language
Choose the multilingual OSD menu. Press  t or u into the sub 
menu and then use the 	p or q	key to select your preferred  
language. Press "Select (Enter)" to finalize the selection.
  Input Filter
Enable the input filter. Press  t or u	into the next menu as below 
and then use 	p or q	to select. Press "Select (Enter)" to finalize 
the selection. The projector will not search inputs that are  
de-selected.
Setup      
						

							English

User Controls
 Source Lock
When this function is turned off, the projector will search for other 
signals if the current input signal is lost. When this function is 
turned on, it will search for a specified connection port.
 High Altitude
Choose "On" to turn on High Altitude mode. Operates the fans at 
full speed continuously to allow for proper high altitude cooling of 
the projector.
 Information Hide
Suppress informational messages on the projected screen.
	On: No status messages appear on screen during operation.
	Off: Status messages appear as normal on screen during  
operation.
  Auto Power Off
Set the time interval (in minutes) to power off the system if there is 
no input signal detected.
 Signal
      VGA Source                                      Video Source
     HDMI Source      
						

							
User Controls
	Automatic: Enable or disable Automatic to automatically select 
the appropriate settings.
Enabled - the projector will automatically select the  
appropriate settings.
Disabled - the projector won’t automatically select the  
appropriate settings.
Frequency: Change the display data frequency to match the frequency of your computer's graphic card. When you  
experience a vertical flickering bar, use this function to make an 
adjustment.
Phase: Synchronize the signal timing of the display with the graphics card. If you experience an unstable or flickering  
image, use this function to correct it.
H Position: Adjust the horizontal position.
V Position: Adjust the vertical position.
White Level: Allow user to adjust White Level when inputting SVideo or Video/CVBS signals.
Black Level: Allow user to adjust Black Level when inputting SVideo or Video/CVBS signals.
Saturation: Adjust a video image from black and white to fully 
saturated color. Press the t to decrease the amount of color in 
the image. Press the u to increase the amount of color in the 
image.
Hue: Adjust the color balance of red and green. Press the  t 
to increase the amount of green in the image. Press the  u to 
increase the amount of red in the image.
  IRE:  Adjust measurement of composite video signals.
 Black Level (for HDMI): Allows user to adjust the Black Level 
for HDMI signals.
Signal Power On

 Off:  Projector can only be turned on by pressing the "Power" 
button.
  On: Projector turns on automatically when an active signal is 
detected. 

"IRE" is only supported 
on NTSC signal.
NoteNote      
						

							English

Appendices
 Security

Security Timer: Enter the Security Timer sub menu to change the settings. 
Enter the Months, Days, and hours that the projector can be 
used without entering the password. Exiting to the Setup menu 
activates the Security Timer. 
Once activated, the projector requires a password on the 
specified dates and times to allow power on and access to the 
security menu. 
If the projector is in use and the Security Timer is active, the 
Password screen displays 60 seconds before the password is 
required.
 Security Setting: Enable or disable the security password.
Enabled -  the current password is required to power on the 
projector and access the Security menu.
Disabled -  Disabled-no password is required for any  
function.
When security is enabled, the Password screen displays at 
startup and before access to the Security menu is allowed:
  Reset
Return the adjustments and settings to factory default values.
Current: Return the current menu's settings to factory default .
 All: Return the settings for all menus to factory default values .


No password is 
required to access 
Setup | Security unless 
the Security Timer or 
Security Settings are 
enabled.
NoteNote      
						

							
Appendices
Image
	No image appears on-screen
	Ensure all the cables and power connections are correctly and 
securely connected as described in the "Installation" section.
	 Ensure the pins of connectors are not crooked or broken.
	Check if the projection lamp has been securely installed. Please 
refer to the "Replacing the Lamp" section.
	 Make sure you have removed the lens cap and the projector is 
switched on.
 Image is out of focus
	 Make sure the Lens cap is removed.
	Adjust the Focus Ring on the projector lens.  
	 Make sure the projection screen is between the required distance 
from the projector. See pages 16.
  The image is stretched when displaying 16:9 DVD title
	When you play anamorphic DVD or 16:9 DVD, the projector will 
show the best image in 16: 9 format on projector side.
	If you play the LBX format DVD title, please change the format as 
LBX in projector OSD.
	If you play 4:3 format DVD title, please change the format as 4:3 in 
projector OSD.
	If the image is still stretched, you will also need to adjust the aspect 
ratio by referring to the following:
	Please setup the display format as 16:9 (wide) aspect ratio type on 
your DVD player.
Troubleshooting
 If you experience a problem with your projector, 
please refer to the following information. If a  problem persists, please contact your local reseller or service center.       
						

							English

Appendices
 Image is too small or too large
	Adjust the zoom lever from the lens.
	Move the projector closer to or further from the screen.
	 Press [Menu] on the projector panel, go to "Display->Format".  
Try the different settings.
 Image has slanted sides:
	If possible, reposition the projector so that it is centered on the 
screen and below the bottom of the screen and use PureShift to 
make adjustments to the image position.
	Use "Display->V Keystone" from the OSD to make an adjustment.
 Image is reversed
	Select "System->Projection" from the OSD and adjust the  
projection direction.
Other
 The projector stops responding to all controls
	If possible, turn off the projector, then unplug the power cord and 
wait at least 20 seconds before reconnecting power.
 Lamp burns out or makes a popping sound
	When the lamp reaches its end of life, it will burn out and may 
make a loud popping sound.  If this happens, the projector will not 
turn on until the lamp module has been replaced. To replace the 
lamp, follow the procedures in the "Replacing the Lamp" section on 
page 48.      
						

							0
Appendices
Projector LED Status Indicator
Message
Power LED
 
(Green)Temp LED
 
(Red)Lamp LED
 
(Red)
Standby State (Input power cord)
Slow Flashing 
2 sec off  
2  sec on
Power on (Warming)Flashing 
0.5 sec off  
0.5 sec on
Power on & Lamp lighting
Power off (Cooling)
Flashing 
1 sec off   
1 sec on 
< 10 sec to off
Error (Lamp fail)Flashing 
0.5 sec off  
0.5 sec on
Error (Fan fail)Flashing 
0.5 sec off  
0.5 sec on Flashing 0.5 sec off 
0.5 sec on
Error (Over Temp)Flashing 
0.5 sec off  
0.5 sec on
Steady light => No light => 
NoteNote