Optoma Projector Eh2060 User Manual

English

Installation
Due to the difference 
in applications for each 
country, some regions 
may have different  
accessories.
NoteNote
12V OUT
HDMI 2
HDMI 1
IRL-AUDIO IN-R
VGA / SCART / YPbPr
VGA OUT
AUDIO OUT AUDIO IN
RS-232
VIDEO
S-VIDEO
Y
Pb
PrUSB
E62405SPR
 VGA, DVI, HDMI
Connecting the Projector
6
13
5
Connect to Notebook
24
1.................................................................Audio Cable (Optional Accessory)...


Installation
Due to the difference 
in applications for each 
country, some regions 
may have different  
accessories.
1.............................. RCA Component Cable for YPbPr (Optional Accessory)
2.............................................. Composite Video Cable (Optional Accessory)
3.................................... SCART RGB/S-Video Adapter (Optional Accessory)
4.................................................................HDMI Cable (Optional Accessory)...

English

Installation
Powering On the Projector
1. Remove the lens cover.
2.  Connect the power cord to the projector.
3.  Turn On the connected devices.
4.  Ensure the Power LED is flashing and then press the power 
button to turn On the projector. 
 
The projector's startup logo screen displays and connected 
devices are detected. If the connected device is a laptop, 
press the appropriate keys on the computer keyboard to 
switch the display output to the projector. (Check the user...


Installation
Warning Indicator
▀■ When the Lamp LED indicator lights red, the projector will 
automatically shut itself down. Please contact your local 
reseller or service center. See pages 40.
▀■  When the Temp LED is on a steady (not flashing) red, the 
projector will automatically shut itself down. Under normal 
conditions, the projector can be switched on again after it 
has cooled down. If the problem persists, you should contact 
your local dealer or our service center. See pages 40....

English

Installation
Adjusting the Projected Image
Adjusting the Projector's Height
The projector is equipped with elevator feet for adjusting the image height.
	 To raise the image:
Lift the projector
and press the height-adjuster button. 
The height adjuster drops down
. 
  To lower the image:
Press the height-adjuster button and gently push down the 
projector.
The projector 
table or stand 
should be level 
and sturdy.
Position the  
projector so that 
it is perpendicular 
to the...


Installation
Diagonallength (inch) size of 16:9 Screen
Screen Size W X H (16:9)Projection distance (D)Offset(A)(m)(feet)(m)(feet)WidthHeightWidthHeightwidetelewidetele(m)(feet)
30.00  0.66  0.37  2.18  1.23  - 1.27  - 4.16  0.06  0.18 
40.00  0.89  0.50  2.91  1.63  1.41  1.69  4.62  5.54  0.07  0.25 
60.00  1.33  0.75  4.36  2.45  2.11  2.53  6.93  8.31  0.11  0.37 
80.00  1.77  1.00  5.81  3.27  2.82  3.38  9.24  11.09  0.15  0.49 
100.00  2.21  1.25  7.26  4.09  3.52  4.22  11.55  13.86...

English

User Controls
Using the Remote Control
Power On/Off
Refer to the "Power On the Projector" 
section on page 13.
Refer to the "Power Off the Projector" 
section on page 14.
LaserPress to operate the on-screen pointer.
UpUp arrow when connected through USB 
to a PC.
LeftLeft arrow when connected through USB 
to a PC.
DownDown arrow when connected through 
USB to a PC.
RightRight arrow when connected through 
USB to a PC.
EnterEnter key when connected through USB 
to a PC....


User Controls
Using the Remote Control
Re-SyncAutomatically synchronize the projector 
to the input source.
Right  
Directional
Select Key
Use directional select keys to select 
items or make adjustments to your selec-
tion.
qDown selection when OSD on.
Page-Page Down key for emulation of USB 
keyboard via USB when OSD off.
Keystone +/-
Press "Keystone +/-" to correct  
image-trapezoid (wider top/bottom)  
effect.
Volume +/-Press "Volume +/-" to adjust volume....

English

User Controls
The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect 
the source. 
How to operate 
1.    To open the OSD menu, press "Menu" on the Remote Control or 
Control Panel.
2    When OSD is displayed, use  p q keys to select any item in the 
main menu.  While making a selection on a particular page, press 
t u or " 
 " key on the Remote Control or...

0
User Controls
Menu Tree