Optoma Projector Eh1060i User Manual

English

User Controls
On the PC (Laptop), select Start -> Control Panel ->  
Network Connections. 
                               
 
                               
Right click on your Local Area Connection and select Properties.  
                              
In the Properties window, select the General tab, and select  
Internet Protocol (TCP/IP).
Click Properties. 
                              
2.
3.
4.
5.      


User Controls
6. Fill in the IP address and Subnet mask, then press OK.  
7. Press the Menu button on the projector.
8. Select OSD-> SETUP-> Network-> Enabled.
9. Input the following:
 IP Address:  10.10.10.10
 Subnet Mask:  255.255.255.0
 Gateway:  0.0.0.0
 DNS:  0.0.0.0
10. Press Apply (Enter) to confirm settings. 11. Open a web browser.
12. In the Address bar, input the IP address: 10.10.10.10. 
13. Press Apply.
The projector is setup for remote management. The Network function...

English

User Controls
14. Based on network web-page for the input-string in [tools] tab, the 
limitation for Input-Length is in the below list (“space” and the other 
punctuation key included): 
CategoryItemInput-Length (characters)
Crestron Control IP Address
15
IP ID 2
Port 5
Projector Projector Name 10
Location
9
Assigned To 9
Network Configuration DHCP (Enabled) (N/A)
IP Address
15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User Password Enabled
(N/A)
New Password 15
Confirm 15
Admin...


User Controls
 Language
Choose the multilingual OSD menu. Press  t or u into the sub 
menu and then use the 	p or q	key to select your preferred  
language. Press "Select (Enter)" to finalize the selection.
  Input Filter
Enable the input filter. Press  t or u	into the next menu as below 
and then use 	p or q	to select. Press "Select (Enter)" to finalize 
the selection. The projector will not search inputs that are  
de-selected.
Setup      

English

User Controls
 Source Lock
When this function is turned off, the projector will search for other 
signals if the current input signal is lost. When this function is 
turned on, it will search for a specified connection port.
 High Altitude
Choose "On" to turn on High Altitude mode. Operates the fans at 
full speed continuously to allow for proper high altitude cooling of 
the projector.
 Information Hide
Suppress informational messages on the projected screen.
	On: No status...


User Controls
	Automatic: Enable or disable Automatic to automatically select 
the appropriate settings.
Enabled - the projector will automatically select the  
appropriate settings.
Disabled - the projector won’t automatically select the  
appropriate settings.
Frequency: Change the display data frequency to match the frequency of your computer's graphic card. When you  
experience a vertical flickering bar, use this function to make an 
adjustment.
Phase: Synchronize the signal timing...

English

Appendices
 Security

Security Timer: Enter the Security Timer sub menu to change the settings. 
Enter the Months, Days, and hours that the projector can be 
used without entering the password. Exiting to the Setup menu 
activates the Security Timer. 
Once activated, the projector requires a password on the 
specified dates and times to allow power on and access to the 
security menu. 
If the projector is in use and the Security Timer is active, the 
Password screen displays 60...


Appendices
Image
	No image appears on-screen
	Ensure all the cables and power connections are correctly and 
securely connected as described in the "Installation" section.
	 Ensure the pins of connectors are not crooked or broken.
	Check if the projection lamp has been securely installed. Please 
refer to the "Replacing the Lamp" section.
	 Make sure you have removed the lens cap and the projector is 
switched on.
 Image is out of focus
	 Make sure the Lens cap is...

English

Appendices
 Image is too small or too large
	Adjust the zoom lever from the lens.
	Move the projector closer to or further from the screen.
	 Press [Menu] on the projector panel, go to "Display->Format".  
Try the different settings.
 Image has slanted sides:
	If possible, reposition the projector so that it is centered on the 
screen and below the bottom of the screen and use PureShift to 
make adjustments to the image position.
	Use "Display->V Keystone" from the...

0
Appendices
Projector LED Status Indicator
Message
Power LED
 
(Green)Temp LED
 
(Red)Lamp LED
 
(Red)
Standby State (Input power cord)
Slow Flashing 
2 sec off  
2  sec on
Power on (Warming)Flashing 
0.5 sec off  
0.5 sec on
Power on & Lamp lighting
Power off (Cooling)
Flashing 
1 sec off   
1 sec on 
< 10 sec to off
Error (Lamp fail)Flashing 
0.5 sec off  
0.5 sec on
Error (Fan fail)Flashing 
0.5 sec off  
0.5 sec on Flashing 0.5 sec off 
0.5 sec on
Error (Over Temp)Flashing 
0.5 sec off  
0.5...