Optoma Hd83 Projector User Manual

English

Introduction

MnO2-LiCELL3VOLTSJAPANHCR2025
M3VOLTSCR2025

3VOLTSCR2025

PowerOnOff
MENU
Re-SyncSourceSBSMode

Backup Remote Control
Power Off
Power On
Enter
Four Directional Select Keys
SBS Mode
Source
Re-Sync
Menu
.
2.
3.
4.
5.
6.
7.
8.
1
3
5
6
8
7
2
4
When using the remote control for the first time, remove the trans-parent insulation tape.

Coin Cell Battery Replacement
12
34
Backup remote control is mag-netically attached on the bottom of the projector.
...

English2

Installation

R

Due to the difference in ap-plications for each country, some regions may have different acces-sories.* Optional Acces-sory


RS232 Cable *
VGA Input Cable *
HDMI Cable *
Power Cord
.
2.
3.
4.
34
12
Connect to Computer/Notebook
NOTE 

English3

Installation

R

Composite Video Cable
Emitter cable *
RCA Component Cable for YPbPr *
VGA to RCA Component Cable for YPbPr *
HDMI Cable *
Power Cord
.
2.
3.
4.
5.
6.
45
1
2
Connect to Video
6Due to the difference in ap-plications for each country, some regions may have different acces-sories.2V Trigger B is programmable trigger.For more detailed information about connecting to the 3D emitter and 3D glasses, please refer to their user’s guides.Use high speed HDMI cable to...

English4

Installation

Connect to 3D Video Devices
The 3D video source device must be powered on before the 3D projector.

If input video is normal 2D, please press “SBS Mode” and switch to “Off”.If “SBS Mode” is active, 2D video content will not display correctly.


NOTE
NOTEOnce you have connected your devices together with HDMI 
cables, as shown in the diagram, you are ready to begin. 
Power ON your 3D video source and your 3D projector.
PlayStation® 3 GamesMake sure that you have updated...

English5

Installation

POWERTEMPLAMPSTAND BY

3D Broadcast3D Blu-ray™ Disc3D Console Games
SKY+HD, cable/satellite boxBlu-ray 3D™ PlayerPlayStation® 3
3D Glasses
Full 3D 080p DLP® Projector
All other product names, company names and trade names used herein are for identifi  cations purposes only and may be trademarks or registered trademarks of their respective \
owners. All images have been simulated. 

English6

Installation

To turn ON 3D glasses: Press the “Power” button and the LED will flash one time indicating the glasses are ready to use 3D mode.Verify that 3D content is being sent to the projector and signal is compa\
t-ible with projector specifications.Turn on the “3D Mode” (DLP-Link/VESA 3D) of the 3D projector. The op-tion is located in the “Display” section of the projector OSD menu\
.Turn on 3D glasses and verify image appears in 3D without eyestrain.If the image does not appear in...

English7

Installation

POWER
TEMP
LAMPSTANDBY

POWERTEMPLAMPSTANDBY

Powering On the Projector
.  Remove the lens cap. 
2.  Securely connect the power cord and signal cable. When con-
nected, the Power LED will turn red.
3.  Turn on the lamp by pressing “” button on the side of the projec-
tor or on the remote control. The Power LED will fl ash blue. 
The startup screen will display in approximately 30 seconds. The 
fi rst time you use the projector, you can select your preferred lan-
guage...

English8

Installation

Powering Off the Projector
. Press the “  ” button on the remote control or “” button on the 
side of the projector two times with one second interval to turn off 
the projector. First time to push the button will display the follow-
ing message on the screen.
Press the “  ” button again to confirm the shut down. If the button 
is not pressed, the message will disappear after 5 seconds.
2. The cooling fans continue to operate for about 60 seconds for 
cooling cycle...

English9

Installation

Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting the 
image height.
To raise the image:
Use screw in foot to raise the image to the desired height angle 
and fine-tune the display angle. 
To lower the image:
Use screw in foot to lower the image to the desired height angle 
and fine-tune the display angle. 


Tilt-Adjustment Feet

Adjusting the Projected Image 

English20

Installation

Horizontal Lens 
Shift Lever
Adjusting Projected Image Position 
Using PureShift
The PureShift feature provides a lens shift function that can be 
used to adjust the position of the projected image either horizontally 
or vertically within the range detailed below. PureShift is a unique 
system that provides lens shift while maintaining a much higher ANSI 
contrast ratio than traditional lens shift system.
Adjusting the vertical image position
The minimum vertical image offset...