Optoma Hd806 Isf Projector User Manual

							English
21
User Controls
Menu Tree1 EnglishExit
Brite Mode
Lam
p Reset Yes/NoOn/Off
Lam
p Reminder
Off(0)/(1~10)
Off(0)/(1~2)On(1)/Off(0)
On/Off Mid
User:Red Gain/Green Gain/
Blue Gain/Red Bias/
Green Bias/Blue BiasCold
Test Pattern Grid/White Pattern/Non
e
SYSTEM|Lamp Setting Lamp Hour
Format
White Level/Black Level/Saturation/Hue/IRE16:9/4:3/LBX/Native
In
put Source
Back
ground
Dark Blue/Black/Gray/Start Logo
H Ima
ge Shift
SuperWide
Ed
ge Mask
V Image Shift
Language
Source Lock
SETUP 12V Tri
gger
Lamp Setting 
Projection Overscan
Color Tem
p
DISPLAY
Warm
True Vivid
Ed
ge EnhanceB/W Extension Gamma
Film/Video/Gra
phics/PC
Degamma Cinema/Bri
ght/TV/sRGB/UserContrast
Brightness
Color
Noise Reduction
IMAGE
Mode
Tint
IMAGE|Advanced Advanced
Shar
pness
Phase/Trackin
g/H Position/V Position
Hi
gh Altitude
On/Off
Si
gnal On/Off
English/Deutsch/Français/Italiano/Español/ Português/Polski/Nederlands/ 

						

							22
User Controls
Image
 Mode
There are many factory presets optimized for various types of im-
ages.
 Cinema: For home theater.
 Bright: For the brightest possible image, Use if ambient light is 
present.
 TV: For watching analogue or digital TV images.
 sRGB: For standard color.
 User: Memorize user’s settings.
  Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. Adjusting the contrast changes the 
amount of black and white in the image.
 Press the  to decrease the contrast.
 Press the  to increase the contrast.
  Brightness
Adjust the brightness of the image.
 Press the  to darken image.
 Press the  to lighten the image.
 Color
Adjusts a video image from black and white to fully saturated color.
 Press the  to decrease the amount of color in the image.
 Press the  to increase the amount of color in the image. 
“Image mode-->TV” will support automati-cally “Overscan” with step “2” as default.
NoteNote       
						

							English
23
User Controls
 Tint 
Adjusts the color balance of red and green.
 Press the  to increase the amount of green in the image.
 Press the  to increase the amount of red in the image.
 Sharpness 
Adjusts the sharpness of the image.
 Press the  to decrease the sharpness.
 Press the  to increase the sharpness.       
						

							24
User Controls
 Noise Reduction
The motion Adaptive Noise Reduction reduces the amount of vis-
ible noise interlaced signals. The range is from “0” to “10”. (0:Off)
 Gamma
This unit comes with 10 preset gamma curves. After the initial setup 
and fine tuning is completed, utilize the Gamma Adjustment steps 
to optimize your image output.
 Degamma
This allows you to choose a degamma table that has been fine-tuned 
to bring out the best image quality for the input.
 Film: For home theater.
 Video: For video or TV source.
 Graphics: For image source.
 PC: For PC or computer source.
  True Vivid
This adjustable item utilizes a new color-processing algorithm and 
enhancements to enable the picture’s vividness to be significantly 
increased. The range is from “0” to “5”.
 Edge Enhance
There are 3 pre-set modes and one user mode for advanced edge 
enhancement filter. You can easily switch between the modes to 
achieve different effects. (0:Off)
 B/W Extension
Black and White Extension can stretch the black and white levels to 
automatically  increase  the  contrast  of  input  image.  This  unit  has  2 
Image | Advance
“B/W Extension” can’t support when source is HDMI, analog or digi-tal RGB via DVI port.
NoteNote       
						

							English
25
User Controls
pre-set modes that allow the user to switch among the pre-sets to 
obtain different image effects. (0:Off/1:On)
 Color Temp.
Adjust the color temperature. At cold temperature, the screen 
looks colder; at warm temperature, the screen looks warmer. 
1)   For User mode adjustment, put cursor on “User”, and press 
“Enter” to select this adjustment item.
2)  Use “”, “” to highlight the desired adjustment items, then 
press “Enter” or “” to select it. The Menu disappears and 
only an adjustment bar appears.
3)  Use “”, “” arrow keys to adjust image.
        
						

							26
User Controls
 Format
Use this function to choose your desired aspect ratio.
 4:3: This format is for 4x3 input sources not enhanced for Wide-
screen TV.
 16:9: This format is for 16x9 input sources, like HDTV and DVD 
enhanced for Widescreen TV.
 Native: This format displays the original image without any scal-
ing.
Display
Input Signal
Display area
Picture area
Display on Screen       
						

							English
27
User Controls
 LBX: This format is for non-16x9, letterbox source and for 
users who use external 16x9 lens to display 2.35:1 aspect ratio 
using full resolution. 
Detail informations about LBX mode :
1.  Some Letter-Box DVDs are not enhanced for 16x9 TVs. In 
this situation, the image will not look right when dis-
played in 16:9 mode. 
In this situation, please try to using the 4:3 mode to view 
the DVD.
But if the content itself is not 4:3, it will have black bars 
around the image in a 16:9 display. For this kind of con-
tent, you can use LBX mode to fill the image in the 16x9 
display as much as possible. 
2.  If you use an external 16x9 lens, this LBX mode also allows 
you to watch a 2.35:1 content (include Anamorphic DVD 
and HDTV film source) that support anamorphic wide is 
enhanced for 16x9 Display in a wide 2.35:1 image. 
In this case, there are no black bars, the full lamp power 
and vertical resolution is fully utilized for maximum view-
ing effects.
Other than these two occasions, one should stay with 16:9 
and 4:3 modes for most viewing experiences. 
 Overscan
Overscan function removes the noise in a video image. Overscan 
the image to remove video encoding noise on the edge of video 
source.
 Edge Mask
 Press the  to reduce the size of an image.
 Press the  to magnify an image on the projection screen.
 H Image Shift
Shifts the projected image position horizontally. 
 V Image Shift
Shifts the projected image position vertically. 
(*) Each I/O has differ-ent setting of “Over-scan”.
(*) “Image mode-->TV” will support automati-cally “Overscan” with step “2” as default.
(*) “Overscan” and “Edge mask” can’t work at same time.
(*) “H Image shift” only support in format “4:3” and “Native”. If source is 1080i/p, “H Image shift” only support in format “4:3”.
NoteNote       
						

							28
User Controls
 V Keystone
Press the  or  to adjust image distortion vertically and makes a 
squarer image.
 SuperWide
 Off: The format can be chosen your desired aspect ratio includ-
ing 4:3, 16:9, LBX and Native.
 On: The format only can be chosen 4:3 and 16:9.
 Auto: To solve the differences of the film formats, the option can 
keep the format in the same ratio.
  “SuperWide“ is “Off“ as default.
  How to use “Super-Wide”
1. Use a 2.0:1 screen that buy from Op-toma 
2. Enable SuperWide feature to Auto
3. Use zoom ring in top of projector to fit the image width to the screen width
NoteNote       
						

							English
29
User Controls
 Language
Choose the multilingual OSD menu. Press  or   into the sub 
menu and then use the   or  key to select your preferred lan-
guage. Press “Select (Enter)” to finalize the selection.
 Input Source
Enable input sources. Press  or  into the next menu as below and 
then use  or  to select. Press “Select (Enter)” to finalize the selec-
tion. The projector will not search inputs that are de-selected.
 Source Lock
When this function is turned off, the projector will search for other 
signals if the current input signal is lost. When this function is 
turned on, it will search for a specified connection port.
Setup       
						

							30
User Controls
 High Altitude
Choose “On” to turn on High Altitude mode. Operates the fans at 
full speed continuously to allow for proper high altitude cooling of 
the projector.
 Auto Power Off
Sets the interval of power-off of the system, if there is no signal 
input. (In minutes)
RGB/HDTV SourceVideo Source
 Signal
 Phase: Changes the display data frequency to match the fre-
quency of your computer’s graphic card. When you experience a 
vertical flickering bar, use this function to make an adjustment.
 Tracking : Synchronizes the signal timing of the display with the 
graphics card. If you experience an unstable or flickering image, 
use this function to correct it.
 H Position: Adjusts the horizontal position.
 V Position: Adjusts the vertical position.
 White Level : Allow user adjust White Level when inputting S-
Video or Video/CVBS signals.
 Black Level : Allow user adjust Black Level when inputting S-
Video or Video/CVBS signals.
 Saturation : Adjusts a video image from black and white to fully 
saturated color. Press the  to decrease the amount of color in 
the image. Press the  to increase the amount of color in the im-
age.
“Signal” don’t support when source is HDMI or DVI-D.
NoteNote